Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
This pull request adds support for the last CPU board from
CS GROUP France (previously CSSI).
That CPU board called CMPCPRO has a mpc8321E CPU (Family PQII PRO hence
its name) and can be plugged in place of the CMPC885 board.
In order to support that new board, the following changes are included
in this series:
- Make the mpc8xx watchdog driver more generic for reusing it
with mpc83xx
- Fix various small problems on mpc83xx platform
- Add a GPIO Driver for QE GPIOs
- Add support for mpc832x into mpc83xx SPI driver
- Refactor existing board code that will be shared with new board
- Add the new board
Currently doing 'reset' command in sandbox with tracing enabled causes
SIGSEV
```
Hit any key to stop autoboot: 0
=>
=>
=> reset
resetting ...
Segmentation fault (core dumped)
```
Tracing callback uses RAM buffer for storing tracing reports, but
state_uninit() function unmaps whole RAM, which causes SIGSEV on umapped
memory inside tracing subsystem.
Fix it by disabling tracing before unmapping memory
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add missing check for CONFIG_TRACE:
Signed-off-by: Simon Glass <sjg@chromium.org>
arch/arm/include/asm/posix_types.h and
arch/sandbox/include/asm/posix_types.h should use different defines.
Add SPDX header.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Given a file ../img of size 4294967296 with GPT partition table and
partitions:
=> host bind 0 ../img
=> part list host 0
Disk host-0.blk not ready
The cause is os_filesize() returning int. File sizes must use off_t.
Correct all uses of os_filesize() too.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix a -Wimplicit-fallthrough warning in sandbox_sysreset_request().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CSSI has another CPU board, similar to the CMPC885 board
that get plugged on the two base boards MCR3000_2G and MIAE.
That CPU board is called CMPCPRO because it has a MPC8321E CPU,
also known as Power QUICC II PRO.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
On sunxi boards, SPL looks for U-Boot at a 32 KiB offset, unless SPL is
larger than 32 KiB, in which case U-Boot immediately follows SPL. See
the logic in spl_mmc_get_uboot_raw_sector() and spl_spi_load_image().
In two cases, the existing binman description mismatches the SPL code.
For 64-bit boards, binman would place U-Boot immediately following SPL,
even if SPL is smaller than 32 KiB. This can happen when SPL MMC support
is disabled (i.e. when booting from SPI flash).
In contrast, for 32-bit boards, binman would place U-Boot at 32 KiB,
even if SPL is larger than that. This happens because the 'offset'
property does not consider the size of previous entries.
Fix both issues by setting a minimum size for the SPL entry, which
exactly matches the logic in the SPL code. Unfortunately, this size must
be provided as a magic number, since none of the relevant config symbols
(SPL_PAD_TO, SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR, and SYS_SPI_U_BOOT_OFFS)
are guaranteed to be defined in all cases.
Fixes: cfa3db602c ("sunxi: Convert 64-bit boards to use binman")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
make readq return unsigned long
readq should return 64-bit data
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit de39dc7162 ("arm: armv7-a: Compile and tune for armv7-a
instead of armv5") is used -march=armv7-a option for Omap3 platforms.
With directive ".arch_extension sec" it is possible for -march=armv7-a to
directly use ARM SMC instruction.
So enable ".arch_extension sec" in Omap3 lowlevel_init.S and replace hand
assembled ".word 0xe1600071" by "SMC #1".
Since commit 51d0638650 ("arm: omap-common: add secure smc entry") same
pattern is already used in arch/arm/cpu/armv7/omap-common/lowlevel_init.S.
Signed-off-by: Pali Rohár <pali@kernel.org>
XEN config can be enabled by other platforms (even it doesn't need to make
sense) that's why fix dependencies. XEN (xenbus.c) requires sscanf (also
pvblock needs it). And PVBLOCK is inside drivers/xen folder which requires
XEN to be enabled.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Toolchains which do not directly support using "isb" and "dsb" directly
are no longer functionally supported in U-Boot. Furthermore, clang has
for a long time warned about using the alternate form that we were.
Update the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building for ARM64, we need to pass -ffixed-x18 and otherwise pass
-ffixed-r9. Rather than having this logic in two places, we can do this
once in arch/arm/config.mk. Further, while gcc will ignore being passed
both -ffixed-r9 and -ffixed-x18 and simply use -ffixed-x18, clang will
note that -ffixed-r9 is not used. Remove this duplication to also remove
the warning.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today, only gcc has __builtin_aarch64_crc32b (clang-16 does not, for
example). Make this option depend on CC_IS_GCC.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Default synchronous exceptions handler prints only esr and register
dump. Sometimes it requiers to see an address which caused exceptions
to understand what's going on
ARM ARM in section D13.2.41 states that FAR_EL2 will contain meanfull
value in case of ESR.EC holds 0x20, 0x21, 0x24, 0x25, 0x22, 0x34 or
0x35. Same applies for EL1.
This patch adds function whivh determine current EL, gets correct FAR
register and prints it on panic.
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Some firewalls enabled by ROM are still left on. So some
address space is inaccessible to the bootloader. For example,
in OSPI boot mode we get an exception and the system hangs.
Therefore, disable all the firewalls left on by the ROM.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
u-boot could be run at EL1/EL2/EL3. so we set it as same as EL1 does.
otherwise it will hang when enable mmu, that is what we encounter
in our SOC.
Signed-off-by: meitao <meitaogao@asrmicro.com>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: 3bf38943ae
In order to make invalidation by VA more efficient, set the largest
block mapping to 2MB, mapping it onto level-2. This has no material
impact on u-boot's runtime performance, and allows a huge speedup
when cleaning the cache.
Signed-off-by: Marc Zyngier <maz@kernel.org>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: 417a73581a
Some recent arm64 cores have a facility that allows the page
table walker to track the dirty state of a page. This makes it
really efficient to perform CMOs by VA as we only need to look
at dirty pages.
Signed-off-by: Marc Zyngier <maz@kernel.org>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: 3c433724e6
Makes it possible to use e.g mcu_spi0 for custom board detection.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
For setting up the master firewalls present in the K3 SoCs, the arm64
clusters need to be powered on.
Re-locates the code for atf/optee authentication.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
This matches AM64 and J721e and removes the need to forward
declare k3_spl_init(), k3_mem_init(), and check_rom_loaded_sysfw()
in sys_proto.h.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
These probably should be in some system wide header given their use.
Until then move them out of K3 sys_proto.h so we can finish cleaning
that header out.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This matches how it was done for pre-K3 TI platforms and it allows
us to move the forward declaration out of sys_proto.h.
It also removes the need for K3_BOARD_DETECT as one is free to simply
override the weak function in their board files as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This header is only used locally by K3 init files, no need to have it
up with the global mach includes. Move into local includes.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This function is the same for each device when it needs to shutdown
the R5 core. Move this to the common section and move the remaining
device specific ID list to the device hardware include.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This belongs in the J721e specific file as it is the only place
this is used. Any board level users should use the SOC driver.
While here, move the J721e and J7200 SoC IDs out of sys_proto.h
and into hardware.h. Use a macro borrowed from Rockchip and add
the rest of the SoC IDs for completeness and later use.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The MSMC fixup is something we do based on SoC, not based on the board.
So this fixup does not belong in the board files. Move this to the
mach-k3 common file so that it does not have to be done in each board
that uses these SoCs.
We use ft_system_setup() here instead of ft_board_setup() since it is no
longer board level. Enable OF_SYSTEM_SETUP in the configurations that use
this to keep functionality the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This reverts commit 5717294230. This
does not exist in upstream kernel.org and breaks boot on DRA7-EVMs.
Drop the same.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
