Supported boot device types in iMX8MM: MMC, DHCP.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is
for command fstype.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mm_evk.h is
deleted because "run distro_bootcmd" is required to be the default boot
mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to.
Delete unnecessary environment variables.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
i.MX8M series includes support for high speed modes in uSDHC controllers.
Turn on corresponding configuration options for EVK boards, which would
enable high speed modes to be included in U-Boot.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the watchdog driver is not selected, which causes the following
warnings in both SPL and U-Boot proper:
U-Boot SPL 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300)
Normal Boot
WDT: Started without servicing (60s timeout)
Trying to boot from MMC1
U-Boot 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300)
CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz
Reset cause: POR
Model: FSL i.MX8MM EVK board
DRAM: 2 GiB
WDT: Started without servicing (60s timeout)
....
System reboots after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
It is safe to run SPL with caches enabled on i.MX8, so
remove such restriction.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Adjust the environment for booting a mainline kernel by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for
DRAM and linux suspend voltage requirement.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
