This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Maxim Sloyko <maxims@google.com>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The boot commands have changed in the environment. Add a note about the
incompatible change and how resolve the issue in the board's README.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit c4bd12a7da ("i2c: mux: Generate longer i2c mux name") changed
the naming scheme of i2c devices within a mux. This broke references to
i2c@0 in the Turris Omnia board initialization code.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit switches to DM USB for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The four x16 DDR3 are wired in T-topology. From NXP AN4467:
'Although not required, T-Topologies may also benefit from performing
Write Leveling as there are package delays on both the processor and DDR
devices that can be de-skewed by performing Write Leveling. Therefore,
Freescale recommends determining Write Leveling calibration parameters
for all boards, regardless of topology used.'
That is why write level calibration is also done.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
The existing calibration values were found to be incorrect
in comparison to newly determined values.
The new values were generated with the help of 5 boards. They have
been determined with the NXP Utility 'DDR Stress Test (2.9.0)'.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This patch is necessary for convert this board to dm driver model
DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate pinctrl and regulators to device tree resp. driver model:
Ethernet, NAND and UART.
Drop BOARD_EARLY_INIT_F as it is anyway no longer used.
Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Disable output driver of PAD CCM_PMIC_STBY_REQ. This prevents the
SOC to request for a lower voltage during sleep. This is necessary
because the voltage is changing too slow for the SOC to wake up
properly.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Just give the new Ethernet PHY power save mode circuitry time to settle.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Using CPU temperature grading as a discriminator if the Wi-Fi /
Bluetooth chip is populated is no longer possible due to upcoming
SKUs. Set variant to -wifi only if a valid config block is present
and the product id mentions a SKU with Wi-Fi / Bluetooth.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Use CONFIG_TARGET_... at compile time to differentiate between
Apalis iMX6, Colibri iMX6 and Colibri iMX6ULL. Avoid code
duplication by moving question about Wi-Fi / Bluetooth before
IT/non-IT decision.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add support for new Colibri iMX6ULL SKUs.
While at it also checkpatch fix the whole files.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Fix indentation using tab vs. spaces.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This setup is a bit special as Linux kernel (4.19) is not supporting
in-kernel NFS rootfs mount and Distributed Switch Architecture (DSA)
operation.
For that reason it was necessary to provide a bootarg to allow userspace
enable it afterwards if needed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
As EHCI on i.MX5 has been converted to driver model, the board specific
code, necessary for VBUS USB power supply setup is not needed anymore.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After commit efd0b79106 ("eth: dm: fec: Add gpio phy reset binding")
the in-board file definition of ETH PHY reset can be removed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All socfpga boards except for vining_fpga use DM_I2C. Enable
DM_I2C for this board and set the EEPROM defines via Kconfig
(enabling CONFIG_I2C_EEPROM from MISC).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Series-changes: 2
- added (this) patch to move socfpga_vining to DM_I2C
This patch makes the on-board RTC work on the socfpga_socrates board.
This rtc is present on the board, but it does not work (fails with a
timeout).
This patch adds a weak pull-up on the I2C0-SCL pin connected to the m41t82
RTC on this board. While the SDA line has a pull-up on the pcb, the pull-up
on the SCL line seems to be missing. To work around this, enable the
weak-pull-up feature on this pin.
After applying this patch, the rtc timeout is gone and the 'date' command
can access the rtc chip.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlzAfvkACgkQfxc6PpAI
reYu9AgAjaFmydXjE8DxkSB3rR7DHZFTs1erVKAAL2v+Tdf7LDmz+j6u1M3v55WY
6r54f/gZ1UX5TEmQgEAKLa7QvvRO/lNvSGQnLHhZhv2IVWo7uWCKAUPdQ6XVZnUK
zO5v+ucs9Ne4HxQJHMC509HUIIBbydiRvUm8W0SeBZy4kEyJDuub4L+rpARkXNks
IZfKuY+VS4FK73D4M9PIhoXSubZgVS4AEcapakU1DvEz0kjsN4wr4idGrp3lutPC
455imz83JBq2+mx1oxclOGedkIDzTCq+nWQAwSftMehrJpGrp7RLNo0v4QZZUf4V
LIXRqObIYse9yQLkYPpeBdePMc8/tQ==
=0NJ2
-----END PGP SIGNATURE-----
Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dm
Various minor sandbox iumprovements
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
These two buffers currently conflict if tracing is enabled. Move the
pre-console buffer and update the documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if one of the initcalls fails on sandbox the address printing
is not help, e.g.:
initcall sequence 0000557678967c80 failed at call 00005576709dfe1f (err=-96)
This is because U-Boot gets relocated high into memory and the relocation
offset (gd->reloc_off) does not work correctly for sandbox.
Add support for finding the base address of the text region (at least on
Linux) and use that to set the relocation offset. This makes the output
better:
initcall sequence 0000560775957c80 failed at call 0000000000048134 (err=-96)
Then you use can use grep to see which init call failed, e.g.:
$ grep 0000000000048134 u-boot.map
stdio_add_devices
Of course another option is to run it with a debugger such as gdb:
$ gdb u-boot
...
(gdb) br initcall.h:41
Breakpoint 1 at 0x4db9d: initcall.h:41. (2 locations)
Note that two locations are reported, since this function is used in both
board_init_f() and board_init_r().
(gdb) r
Starting program: /tmp/b/sandbox/u-boot
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/x86_64-linux-gnu/libthread_db.so.1".
U-Boot 2018.09-00264-ge0c2ba9814-dirty (Sep 22 2018 - 12:21:46 -0600)
DRAM: 128 MiB
MMC:
Breakpoint 1, initcall_run_list (init_sequence=0x5555559619e0 <init_sequence_f>)
at /scratch/sglass/cosarm/src/third_party/u-boot/files/include/initcall.h:41
41 printf("initcall sequence %p failed at call %p (err=%d)\n",
(gdb) print *init_fnc_ptr
$1 = (const init_fnc_t) 0x55555559c114 <stdio_add_devices>
(gdb)
Signed-off-by: Simon Glass <sjg@chromium.org>
With the migration to DM in SPL and the DT support, the
old legacy code is no longer neaded, so this patch removes it
Signed-off-by: Adam Ford <aford173@gmail.com>
This is needed to make ethernet work on stm32f746-eval which
uses MII mode.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Amlogic U200 board is based on the Amlogic S905D2 SoC
from the Amlogic G12A SoC family.
The board has the following specifications :
- Amlogic S905D2 ARM Cortex-A53 quad-core SoC
- XGB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
- MIPI DSI Connector
- Audio HAT Connector
- PCI-E M.2 Connector
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When fixing sandbox test for regmap_read_poll_timeout(), the
sandbox_timer_add_offset was introduced but only defined in sandbox code
thus generating warnings when used out of sandbox :
include/regmap.h:289:2: note: in expansion of macro 'regmap_read_poll_timeout_test'
regmap_read_poll_timeout_test(map, addr, val, cond, sleep_us, \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c:169:8: note: in expansion of macro 'regmap_read_poll_timeout'
ret = regmap_read_poll_timeout(spifc->regmap, REG_SLAVE, data,
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c: In function 'meson_spifc_txrx':
include/regmap.h:277:4: warning: implicit declaration of function 'sandbox_timer_add_offset' [-Wimplicit-function-declaration]
This fix adds a timer_test_add_offset() only defined in sandbox, and
renames the previous sandbox_timer_add_offset() to it.
Cc: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
Fixes: df9cf1cc08 ("test: dm: regmap: Fix the long test delay")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvW07AAoJEB6zHgIOrC/Iu4QH/1REDOTrsZPydd2yD/O81vPs
RiLC8wP2J4UmqtMcNTLyvxlYwrzqoR5J6SYdyBNU/+cLEp/gdzEI+rjsfSV2uRX1
Qb4Pk2FiI503JVjegxsbJqzASfiEP7rIg3HM5431xbhYH22MW2FH6le6yrtNxjBh
m1WFjQYX1bpbGb6zue8TgyLIeN1IqWuqnH9kUHixUEan+xrpEhN239LDFjdvGbvC
BvYyMtDddmMt4YDzNjgX36us993kylGZp6JijR3zgUao7I/JGVZAJrxw8MHDTnVy
UKv3VI9F5bGLSvzqTVL2MFU6XtJW26v+niGLhGzlUhb3TTKrdKOicm3VF7tO+JU=
=MamK
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2019.07 cycle
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
to check cable detection.
- the DWC2 driver to support a new dt property
"u-boot,force-b-session-valid" which forces B session and
device mode; it is a workaround because the VBUS sensing and
ID detection isn't available with stusb1600.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Use the DWC2 device driver with DM_USB_GADGET support and
cleanup the USB support in STM32MP1 board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SAMA5D2 ICP Board features the SAMA5D27 SoC,
together with QSPI Flash, Wilc3000 wireless device and
EtherCat support.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
