Apple M2 devices have an MTP coprocessor in charge of keyboard/trackpad
handling, communicating over a DockChannel interface. Add a simple
driver for this.
The keyboard does not require any initialization messages, but we have a
problem: we cannot reset the MTP so Linux can start it fresh, and it
delivers a number of informative packets on startup. To work around
this, we buffer those messages and re-inject them into the FIFO (which
is big enough to hold all of them) on shutdown, so Linux finds them when
it initializes its driver. The actual MTP coprocessor is quiesced, which
does work properly.
Signed-off-by: Hector Martin <marcan@marcan.st>
Without this patch, there will be error indicating that
"Cannot use 64 bit addresses with SDMA", and the booting
process will stuck.
please see full boot log below
U-Boot 2022.04-g18185931 (Sep 11 2024 - 13:15:30 +0800)
SoC: LS1028AE Rev1.0 (0x870b0010)
Clock Configuration:
CPU0(A72):1500 MHz CPU1(A72):1500 MHz
Bus: 400 MHz DDR: 1600 MT/s
Reset Configuration Word (RCW):
00000000: 3c004010 00000030 00000000 00000000
00000010: 00000000 018f0000 0030c000 00000000
00000020: 020031a0 00002580 00000000 00003296
00000030: 00000000 00000010 00000000 00000000
00000040: 00000000 00000000 00000000 00000000
00000050: 00000000 00000000 00000000 00000000
00000060: 00000000 00000000 200e705a 00000000
00000070: bb580000 00000000
Model: LS1028A RDB Board
Board: LS1028AE Rev1.0-RDB, Version: C, boot from SD
FPGA: v8 (RDB)
SERDES1 Reference : Clock1 = 100.00MHz Clock2 = 100.00MHz
DRAM: 3.9 GiB
DDR 3.9 GiB (DDR4, 32-bit, CL=11, ECC on)
Using SERDES1 Protocol: 47960 (0xbb58)
PCIe1: pcie@3400000 Root Complex: no link
PCIe2: pcie@3500000 Root Complex: x1 gen2
Core: 45 devices, 22 uclasses, devicetree: separate
WDT: Started watchdog@c000000 with servicing (60s timeout)
WDT: Started watchdog@c010000 with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
EEPROM: Invalid ID (ff ff ff ff)
In: serial
Out: serial
Err: serial
SEC0: RNG instantiated
Net:
Warning: enetc-0 (eth0) using random MAC address - d2:9b:a5:37:7b:b5
eth0: enetc-0
Warning: enetc-2 (eth1) using random MAC address - ca:57:11🇩🇪de:cb
, eth1: enetc-2, eth2: swp0, eth3: swp1, eth4: swp2, eth5: swp3
Hit any key to stop autoboot: 0
Trying load HDP firmware from SD..
switch to partitions #0, OK
mmc0 is current device
Device: FSL_SDHC
Manufacturer ID: 9f
OEM: 5449
Name: SD32G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 28.9 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
MMC read: dev # 0, block # 18944, count 512 ... 512 blocks read: OK
Loading hdp firmware from 0x00000000a0000000 offset 0x0000000000002000
Loading hdp firmware Complete
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disk mmc@2140000.blk...
Scanning disk mmc@2150000.blk...
Found 7 disks
ERROR: invalid device tree
Found EFI removable media binary efi/boot/bootaa64.efi
981992 bytes read in 44 ms (21.3 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
WARNING could not find node vivante,gc: FDT_ERR_NOTFOUND.
Booting /efi\boot\bootaa64.efi
Cannot use 64 bit addresses with SDMA
Error reading cluster
** Unable to read file /efi/boot/grubaa64.efi **
Unexpected return from initial read: Device Error, buffersize 29D790
Failed to load image ¬ : Device Error
start_image() returned Device Error
EFI LOAD FAILED: continuing...
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
BootOrder not defined
EFI boot manager: Cannot load any image
Scanning mmc 1:2...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
BootOrder not defined
EFI boot manager: Cannot load any image
starting USB...
Bus usb@3100000: Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
Bus usb@3110000: Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus usb@3100000 for devices... 1 USB Device(s) found
scanning bus usb@3110000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
Trying load from SD ...
switch to partitions #0, OK
mmc0 is current device
Device: FSL_SDHC
Manufacturer ID: 9f
OEM: 5449
Name: SD32G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 28.9 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
MMC read: dev # 0, block # 32768, count 81920 ... 81920 blocks read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Signed-off-by: Wei Ming Chen <jj251510319013@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current A/B switching preparatory altbootcmd is confusing
to users, replace it with plain 'run bootcmd' which can be
replaced by proper A/B switching altbootcmd when the matching
updater is added on top of the platform. By default, keep the
boot counter incrementing, but do not do any A/B partition
switching.
Signed-off-by: Marek Vasut <marex@denx.de>
The x250 and SE250 are series of 10G L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
As things have been moved to Kconfig there are a number of dead comments
left over in x530.h. Remove them.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use standard boot instead of the distro boot scripts. Regenerate the
board defconfig now that some options are selected automatically.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Remove CFG_SYS_BAUDRATE_TABLE as there's no reason not to use the
defaults defined via config_fallbacks.h.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/23474
- UFS support is enabled for SC7280 and SM8150 platforms.
- Qualcomm dt-bindings headers are all dropped in favour of
dts/upstream.
- The SMMU driver now correctly handles stream ID 0 and is disabled in
EL2.
- Initial support for capsule updates (using the new dynamic UUIDs) is
added for the RB3 Gen 2 board alongside a new SCSI backend for DFU.
- CONFIG_PINCONF is enabled in qcom_defconfig.
- The vqmmc supply is now enabled for sdcard support on boards that need
it.
- A quirk is added for reading GPIOs on the PM8550 PMIC
Qualcomm boards flash U-Boot a variety of partitions, implement support
for determining which slot U-Boot is running from, finding the correct
partition for that slot and configuring the appropriate DFU string.
Initially, we only support the RB3 Gen 2 where U-Boot is flashed to the
UEFI partition, and ignore handling of slots. In the future we will
additionally support booting U-Boot from other partitions (e.g. boot)
and correct handling for A/B.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add manufacturing environment into STM32MP15xx DH electronics DHSOM
configuration. This environment is part of every board build, but only
takes effect on systems booted with the dh,stm32mp15xx-dhcor-testbench
device tree, i.e. systems populated with factory build of U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add support for Cool Pi GenBook, it works as a carrier board
connect with CM5 SOM.
Specification:
- Rockchip RK3588
- LPDDR5X 8/32 GB
- eMMC 64 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for RTL8852BE Wireless connection
- PCIE M.2 M Key for NVME connection
- eDP panel with 1920x1080
Tested by Armbian boot on USB disk.
Change-Id: I4d9b8572dc7c400077dde666633f3fea1b47dd03
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some board may want to have a different boot priority(a laptop
may want to usb has the highest boot priority for third-part
os installation). So let the board can define it's own
boot_targets.
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Qnap TS433 is a 4-bay NAS based around the RK3568.
Two SATA bays are connected to the RK3568's own SATA controllers while
the other two are connected to a JMicron SATA controller living on the
PCIe bus.
It provides one 2.5Gb and one 1Gb ethernet port as well as 3 usb ports.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Improve "mmcautodetect=yes" boot mode autodetection to able to use it
if CONFIG_ENV_IS_NOWHERE=y is used for i.MX9 SoCs and i.MX93 EVK board.
If both CONFIG_ENV_IS_IN_MMC=y and CONFIG_ENV_IS_NOWHERE=y are in the
defconfig, CONFIG_ENV_IS_IN_MMC=y will be overiden default
CONFIG_ENV_IS_NOWHERE settings.
Goal is in this patch to able to use the boot mode autodetection
if defconfig use only CONFIG_ENV_IS_NOWHERE=y option
(without CONFIG_ENV_IS_IN_MMC) for any i.MX9 SoC.
Signed-off-by: Benjamin Szőke <egyszeregy@freemail.hu>
Leo Yan <leo.yan@arm.com> says:
This patch series is to refine the booting on Arm Total Compuate
platform.
It changes to use the info passed in DTB for initialization DRAM info,
and dynamically initializes the booting envoironment variables.
Another big change is to use an envoironment file for boot commands,
based on it, the series extends to support multiple block devices
(MMC and virtio). And the env file is extended for booting Debian.
The last commit is to update memory mapping info based on the DRAM info
passed via DT binding.
Link: https://lore.kernel.org/r/20241025171821.624702-1-leo.yan@arm.com
The boot command for Total Compute has many aspects and changes from time
to time. So move it to an .env file where it can be a proper script.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
The whole DRAM bank is used for loading and U-boot can detect the
overlap between the kernel and initramfs. So it is safe to drop
bootm_size.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Initialize the environment variables 'fdt_addr_r' and 'kernel_addr_r'
during the misc init phase. The static configurations are not needed,
remove them.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
On Total Compute, TF-A passes the info via DT binding for the hardware
description - includes the serial, memory, and arm_ffa nodes.
This commit initializes the fdt base address based on the passed the
register x1.
The similar implementation has already been done for the raspberry pi,
so borrow a lot of it.
Co-developed-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com>
Signed-off-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com>
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
The Emcraft Systems NavQ+ kit is a mobile robotics platform
based on NXP i.MX8 MPlus SoC.
The following interfaces and devices are enabled:
- eMMC
- Gigabit Ethernet (through eQOS interface)
- SD-Card
- UART console
The device tree file is taken from upstream Linux Kernel
through OF_UPSTREAM
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Jan Kiszka <jan.kiszka@siemens.com> says:
This adds support for the new IOT2050 SM variant, introduces a sysinfo
driver which also permits SMBIOS support and switches the board to
OF_UPSTREAM. There are some further fixes for the boards included as well.
Not yet included is configuration support for DMA isolation via the PVU as
this depends on not yet merged DT bindings and another overlay.
[trini: This is just the first 10 patches in the series for now]
Link: https://lore.kernel.org/r/cover.1729577070.git.jan.kiszka@siemens.com
Due to new DDR size introduction, the current logic of determining the
DDR size is not able to get the correct size.
Instead, the DDR size is determined by the FSBL(SEBOOT) then passed to
u-boot through the scratchpad info.
The SEBoot version must be >= D/V01.04.01.02 to support this change.
Also now for some variants, the DDR size may > 2GB, so borrow some code
from the TI evm to iot2050 to support more than 2GB DDR.
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This prevented to set m2_manual_config - as evaluated by
m2_connector_setup - under strict configurations for secure boot.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
QEMU supports NVMe devices, but U-Boot only tries to boot from Virtio.
This is problematic when explicitly using NVMe, so fix that.
Additionally, RVVM virtual machine is almost fully compatible with QEMU,
except it only implements NVMe drives instead of VirtIO.
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Patrick Rudolph <patrick.rudolph@9elements.com> says:
Based on the existing work done by Simon Glass this series adds
support for booting aarch64 devices using ACPI only.
As first target QEMU SBSA support is added, which relies on ACPI
only to boot an OS. As secondary target the Raspberry Pi4 was used,
which is broadly available and allows easy testing of the proposed
solution.
The series is split into ACPI cleanups and code movements, adding
Arm specific ACPI tables and finally SoC and mainboard related
changes to boot a Linux on the QEMU SBSA and RPi4. Currently only the
mandatory ACPI tables are supported, allowing to boot into Linux
without errors.
The QEMU SBSA support is feature complete and provides the same
functionality as the EDK2 implementation.
The changes were tested on real hardware as well on QEMU v9.0:
qemu-system-aarch64 -machine sbsa-ref -nographic -cpu cortex-a57 \
-pflash secure-world.rom \
-pflash unsecure-world.rom
qemu-system-aarch64 -machine raspi4b -kernel u-boot.bin -cpu cortex-a72 \
-smp 4 -m 2G -drive file=raspbian.img,format=raw,index=0 \
-dtb bcm2711-rpi-4-b.dtb -nographic
Tested against FWTS V24.03.00.
Known issues:
- The QEMU rpi4 support is currently limited as it doesn't emulate PCI,
USB or ethernet devices!
- The SMP bringup doesn't work on RPi4, but works in QEMU (Possibly
cache related).
- PCI on RPI4 isn't working on real hardware since the pcie_brcmstb
Linux kernel module doesn't support ACPI yet.
Link: https://lore.kernel.org/r/20241023132116.970117-1-patrick.rudolph@9elements.com
Add support for Arm sbsa [1] v0.3+ that is supported by QEMU [2].
Unlike other Arm based platforms the machine only provides a minimal
FDT that contains number of CPUs, ammount of memory and machine-version.
The boot firmware has to provide ACPI tables to the OS.
Due to this design a full DTB is added here as well that allows U-Boot's
driver to properly function. The DTB is appended at the end of the U-Boot
image and will be merged with the QEMU provided DTB.
In addition provide documentation how to use, enable binman to fabricate both
ROMs that are required to boot and add ACPI tables to make it full compatible
to the EDK2 reference implementation.
The board was tested using Fedora 40 Aarch64 Workstation. It's able
to boot from USB and AHCI or network.
Tested and found working:
- serial
- PCI
- xHCI
- Bochs display
- AHCI
- network using e1000e
- CPU init
- Booting Fedora 40
1: Server Base System Architecture (SBSA)
2: https://www.qemu.org/docs/master/system/arm/sbsa.html
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/22989
- Remove unneeded USB board code and fix reset on mx6ul_14x14_evk.
- Update fastboot buffer size/address for verdin-imx8m{m|p}.
- Fix imxrt1050-evk boot and convert it to standard boot.
- Fix imx8qxp-mek and imx8qm-mek boot.
- Add support for the i.MX93 9X9 QSB board.
- Make livetree API to work on i.MX.
- Set sane default value for i.MX8M SPL_LOAD_FIT_ADDRESS.
- Deduplicate DH i.MX8MP/i.MX6 DHSOM defconfigs.
- Select default TEXT_BASE for i.MX6/i.MX7.
- Several updates for DH i.MX8MP DRC02.
The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
Features tested on a ODROID-M2 16GB rev1.0 20240611:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To enhance code organization, it is beneficial to consolidate all A/B
BCB management routines into a single super-command.
The 'bcb' command is an excellent candidate for this purpose.
This patch integrates the separate 'ab_select' command into the 'bcb'
group as the 'ab_select' subcommand, maintaining the same parameter list
for consistency.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3_android
Link: https://lore.kernel.org/r/20241017-android_ab_master-v5-3-43bfcc096d95@salutedevices.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/22796
- Switch to using upstream DT on DH i.MX8MP DHCOM PDK2/PDK3.
- Add ability to build fallback DTBOs from arch/$(ARCH)/dts.
- Remove fdt_high and initrd_high env variables from imx6-dhcom.
- Add dummy clk for imx8.
- Fix DT corruption in imx8_cpu.
- Improve DDR stability on pico-imx7d.
Remove both "fdt_high" and "initrd_high" environment variables
in favor of "bootm_size" to safely contain a kernel, device tree
and initrd for relocation inside of 256 MiB region of DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This is cosmetic change.
Remove the empty comment blocks remaining after conversion to Kconfig
of CONFIG_SYS_MAX_NAND_DEVICE and CONFIG_SERVERIP.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Make the dh_update_sd_to_sf script generic, rename it to dh_update_block_to_sf
and implement two specific dh_update_sd_to_sf and dh_update_emmc_to_sf scripts
which load U-Boot from either SD or eMMC and install it into SPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When populating BOOT_TARGET_DEVICES on Amlogic Meson platforms, verify
that the shell commands for accessing the relevant media have been
enabled in the build configuration.
This was already being done for USB, NVME and SCSI devices, but not
for MMC devices or network boot. This meant that configuring U-Boot
without the networking or MMC subsystems/drivers would cause an error
to be thrown during preprocessing.
Signed-off-by: Callum Parsey <callum@neoninteger.au>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241012080340.2596-1-callum@neoninteger.au
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The device tree overlays are not part of the
Android Common Kernel code [1]
Historically, they existed to enable some Android specific
features but they have been removed.
Remove the dtbos logic since these files do no longer exist.
[1] ac2ea0bb91/arch/arm64/boot/dts/amlogic/
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241011-yukawa-aosp-parts-v1-2-7d74aa13ff8e@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Assorted Tegra enhancements. Merged with the recent XPL_BUILD changes,
resolve some whitespace issues and fix the name of the new apalis-tk1
env file by Tom.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert boards to use text based env. This is the first stage of
conversion, common inclusions should be converted next.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Apalis TK1
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.