Merge with git+ssh://sr@pollux.denx.org/home/sr/git/u-boot/denx/.git

This commit is contained in:
Stefan Roese 2006-12-28 19:09:07 +01:00
commit cce2adfb93
23 changed files with 2333 additions and 34 deletions

View file

@ -1539,6 +1539,9 @@ TQM8265_AA_config: unconfig
fi
@$(MKCONFIG) -a TQM8260 ppc mpc8260 tqm8260
TQM8272_config: unconfig
@$(MKCONFIG) -a TQM8272 ppc mpc8260 tqm8272
VoVPN-GW_66MHz_config \
VoVPN-GW_100MHz_config: unconfig
@mkdir -p $(obj)include

View file

@ -31,6 +31,8 @@ DECLARE_GLOBAL_DATA_PTR;
extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
ulong flash_get_size (ulong base, int banknum);
int board_early_init_f(void)
{
unsigned long sdr0_cust0;
@ -152,6 +154,11 @@ int misc_init_r(void)
*/
/* Re-do sizing to get full correct info */
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
gd->bd->bi_flashoffset = 0;
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
mtdcr(ebccfga, pb3cr);
#else
@ -192,9 +199,10 @@ int misc_init_r(void)
#endif
mtdcr(ebccfgd, pbcr);
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
gd->bd->bi_flashoffset = 0;
/*
* Re-check to get correct base address
*/
flash_get_size(gd->bd->bi_flashstart, 0);
#ifdef CFG_ENV_IS_IN_FLASH
/* Monitor protection ON by default */

View file

@ -105,7 +105,7 @@ static int ppchameleonevb_device_ready(struct mtd_info *mtdinfo)
* Members with a "?" were not set in the merged testing-NAND branch,
* so they are not set here either.
*/
void board_nand_init(struct nand_chip *nand)
int board_nand_init(struct nand_chip *nand)
{
nand->hwcontrol = ppchameleonevb_hwcontrol;
@ -113,5 +113,6 @@ void board_nand_init(struct nand_chip *nand)
nand->eccmode = NAND_ECC_SOFT;
nand->chip_delay = NAND_BIG_DELAY_US;
nand->options = NAND_SAMSUNG_LP_OPTIONS;
return 0;
}
#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */

View file

@ -448,7 +448,7 @@ static void dfc_gpio_init(void)
* Members with a "?" were not set in the merged testing-NAND branch,
* so they are not set here either.
*/
void board_nand_init(struct nand_chip *nand)
int board_nand_init(struct nand_chip *nand)
{
unsigned long tCH, tCS, tWH, tWP, tRH, tRP, tRP_high, tR, tWHR, tAR;
@ -576,6 +576,7 @@ void board_nand_init(struct nand_chip *nand)
nand->cmdfunc = dfc_cmdfunc;
nand->autooob = &delta_oob;
nand->badblock_pattern = &delta_bbt_descr;
return 0;
}
#else

View file

@ -106,12 +106,13 @@ static void nc650_hwcontrol(struct mtd_info *mtd, int cmd)
* Members with a "?" were not set in the merged testing-NAND branch,
* so they are not set here either.
*/
void board_nand_init(struct nand_chip *nand)
int board_nand_init(struct nand_chip *nand)
{
nand->hwcontrol = nc650_hwcontrol;
nand->eccmode = NAND_ECC_SOFT;
nand->chip_delay = 12;
/* nand->options = NAND_SAMSUNG_LP_OPTIONS;*/
return 0;
}
#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */

View file

@ -55,12 +55,13 @@ static int netstar_nand_ready(struct mtd_info *mtd)
}
***/
void board_nand_init(struct nand_chip *nand)
int board_nand_init(struct nand_chip *nand)
{
nand->options = NAND_SAMSUNG_LP_OPTIONS;
nand->eccmode = NAND_ECC_SOFT;
nand->hwcontrol = netstar_nand_hwcontrol;
/* nand->dev_ready = netstar_nand_ready; */
nand->chip_delay = 18;
return 0;
}
#endif

View file

@ -148,7 +148,7 @@ static int pdnb3_nand_dev_ready(struct mtd_info *mtd)
return 1;
}
void board_nand_init(struct nand_chip *nand)
int board_nand_init(struct nand_chip *nand)
{
pdnb3_ndfc = (struct pdnb3_ndfc_regs *)CFG_NAND_BASE;
@ -167,5 +167,6 @@ void board_nand_init(struct nand_chip *nand)
nand->read_buf = pdnb3_nand_read_buf;
nand->verify_buf = pdnb3_nand_verify_buf;
nand->dev_ready = pdnb3_nand_dev_ready;
return 0;
}
#endif

40
board/tqm8272/Makefile Normal file
View file

@ -0,0 +1,40 @@
#
# (C) Copyright 2001
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
include $(TOPDIR)/config.mk
LIB = lib$(BOARD).a
OBJS = $(BOARD).o ../tqm8xx/load_sernum_ethaddr.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
#########################################################################
.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
sinclude .depend
#########################################################################

34
board/tqm8272/config.mk Normal file
View file

@ -0,0 +1,34 @@
#
# (C) Copyright 2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
#
# TQM8272 boards
#
# This should be equal to the CFG_FLASH_BASE define in config_TQM8260.h
# for the "final" configuration, with U-Boot in flash, or the address
# in RAM where U-Boot is loaded at for debugging.
#
TEXT_BASE = 0x40000000
PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)

1234
board/tqm8272/tqm8272.c Normal file

File diff suppressed because it is too large Load diff

126
board/tqm8272/u-boot.lds Normal file
View file

@ -0,0 +1,126 @@
/*
* (C) Copyright 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
OUTPUT_ARCH(powerpc)
SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
/* Do we need any of these for elf?
__DYNAMIC = 0; */
SECTIONS
{
/* Read-only sections, merged into text segment: */
. = + SIZEOF_HEADERS;
.interp : { *(.interp) }
.hash : { *(.hash) }
.dynsym : { *(.dynsym) }
.dynstr : { *(.dynstr) }
.rel.text : { *(.rel.text) }
.rela.text : { *(.rela.text) }
.rel.data : { *(.rel.data) }
.rela.data : { *(.rela.data) }
.rel.rodata : { *(.rel.rodata) }
.rela.rodata : { *(.rela.rodata) }
.rel.got : { *(.rel.got) }
.rela.got : { *(.rela.got) }
.rel.ctors : { *(.rel.ctors) }
.rela.ctors : { *(.rela.ctors) }
.rel.dtors : { *(.rel.dtors) }
.rela.dtors : { *(.rela.dtors) }
.rel.bss : { *(.rel.bss) }
.rela.bss : { *(.rela.bss) }
.rel.plt : { *(.rel.plt) }
.rela.plt : { *(.rela.plt) }
.init : { *(.init) }
.plt : { *(.plt) }
.text :
{
cpu/mpc8260/start.o (.text)
*(.text)
common/environment.o(.text)
*(.fixup)
*(.got1)
. = ALIGN(16);
*(.rodata)
*(.rodata1)
*(.rodata.str1.4)
*(.eh_frame)
}
.fini : { *(.fini) } =0
.ctors : { *(.ctors) }
.dtors : { *(.dtors) }
/* Read-write section, merged into data segment: */
. = (. + 0x0FFF) & 0xFFFFF000;
_erotext = .;
PROVIDE (erotext = .);
.reloc :
{
*(.got)
_GOT2_TABLE_ = .;
*(.got2)
_FIXUP_TABLE_ = .;
*(.fixup)
}
__got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
__fixup_entries = (. - _FIXUP_TABLE_) >> 2;
.data :
{
*(.data)
*(.data1)
*(.sdata)
*(.sdata2)
*(.dynamic)
CONSTRUCTORS
}
_edata = .;
PROVIDE (edata = .);
. = .;
__u_boot_cmd_start = .;
.u_boot_cmd : { *(.u_boot_cmd) }
__u_boot_cmd_end = .;
. = .;
__start___ex_table = .;
__ex_table : { *(__ex_table) }
__stop___ex_table = .;
. = ALIGN(4096);
__init_begin = .;
.text.init : { *(.text.init) }
.data.init : { *(.data.init) }
. = ALIGN(4096);
__init_end = .;
__bss_start = .;
.bss :
{
*(.sbss) *(.scommon)
*(.dynbss)
*(.bss)
*(COMMON)
}
_end = . ;
PROVIDE (end = .);
}

View file

@ -448,7 +448,7 @@ static void dfc_gpio_init(void)
* Members with a "?" were not set in the merged testing-NAND branch,
* so they are not set here either.
*/
void board_nand_init(struct nand_chip *nand)
int board_nand_init(struct nand_chip *nand)
{
unsigned long tCH, tCS, tWH, tWP, tRH, tRP, tRP_high, tR, tWHR, tAR;
@ -576,6 +576,7 @@ void board_nand_init(struct nand_chip *nand)
nand->cmdfunc = dfc_cmdfunc;
nand->autooob = &delta_oob;
nand->badblock_pattern = &delta_bbt_descr;
return 0;
}
#else

View file

@ -49,6 +49,10 @@
DECLARE_GLOBAL_DATA_PTR;
#if defined(CONFIG_GET_CPU_STR_F)
extern int get_cpu_str_f (char *buf);
#endif
int checkcpu (void)
{
volatile immap_t *immap = (immap_t *) CFG_IMMR;
@ -81,7 +85,12 @@ int checkcpu (void)
if ((immr & IMMR_ISB_MSK) != CFG_IMMR)
return -1; /* whoops! someone moved the IMMR */
#if defined(CONFIG_GET_CPU_STR_F)
get_cpu_str_f (buf);
printf ("%s (HiP%d Rev %02x, Mask ", buf, k, rev);
#else
printf (CPU_ID_STR " (HiP%d Rev %02x, Mask ", k, rev);
#endif
/*
* the bottom 16 bits of the immr are the Part Number and Mask Number

View file

@ -28,6 +28,10 @@
DECLARE_GLOBAL_DATA_PTR;
#if defined(CONFIG_BOARD_GET_CPU_CLK_F)
extern unsigned long board_get_cpu_clk_f (void);
#endif
static void config_8260_ioports (volatile immap_t * immr)
{
int portnum;
@ -90,6 +94,7 @@ static void config_8260_ioports (volatile immap_t * immr)
}
}
#define SET_VAL_MASK(a, b, mask) ((a & mask) | (b & ~mask))
/*
* Breath some life into the CPU...
*
@ -101,6 +106,9 @@ void cpu_init_f (volatile immap_t * immr)
{
#if !defined(CONFIG_COGENT) /* done in start.S for the cogent */
uint sccr;
#endif
#if defined(CONFIG_BOARD_GET_CPU_CLK_F)
unsigned long cpu_clk;
#endif
volatile memctl8260_t *memctl = &immr->im_memctl;
extern void m8260_cpm_reset (void);
@ -119,10 +127,27 @@ void cpu_init_f (volatile immap_t * immr)
immr->im_clkrst.car_rmr = CFG_RMR;
/* BCR - Bus Configuration Register (4-25) */
#if defined(CFG_BCR_60x) && (CFG_BCR_SINGLE)
if (immr->im_siu_conf.sc_bcr & BCR_EBM) {
immr->im_siu_conf.sc_bcr = CFG_BCR_60x;
} else {
immr->im_siu_conf.sc_bcr = CFG_BCR_SINGLE;
}
#else
immr->im_siu_conf.sc_bcr = CFG_BCR;
#endif
/* SIUMCR - contains debug pin configuration (4-31) */
#if defined(CFG_SIUMCR_LOW) && (CFG_SIUMCR_HIGH)
cpu_clk = board_get_cpu_clk_f ();
if (cpu_clk >= 100000000) {
immr->im_siu_conf.sc_siumcr = CFG_SIUMCR_HIGH;
} else {
immr->im_siu_conf.sc_siumcr = CFG_SIUMCR_LOW;
}
#else
immr->im_siu_conf.sc_siumcr = CFG_SIUMCR;
#endif
config_8260_ioports (immr);
@ -157,7 +182,8 @@ void cpu_init_f (volatile immap_t * immr)
#endif
/* now restrict to preliminary range */
memctl->memc_br0 = CFG_BR0_PRELIM;
/* the PS came from the HRCW, don´t change it */
memctl->memc_br0 = SET_VAL_MASK(memctl->memc_br0 , CFG_BR0_PRELIM, BRx_PS_MSK);
memctl->memc_or0 = CFG_OR0_PRELIM;
#if defined(CFG_BR1_PRELIM) && defined(CFG_OR1_PRELIM)

View file

@ -274,7 +274,23 @@ void pci_mpc8250_init (struct pci_controller *hose)
| SIUMCR_CS10PC00
| SIUMCR_BCTLC00
| SIUMCR_MMR11;
#elif defined(CONFIG_TQM8272)
#if 0
immap->im_siu_conf.sc_siumcr = (immap->im_siu_conf.sc_siumcr &
~SIUMCR_LBPC11 &
~SIUMCR_CS10PC11 &
~SIUMCR_LBPC11) |
SIUMCR_LBPC01 |
SIUMCR_CS10PC01 |
SIUMCR_APPC10;
#else
#if 0
immap->im_siu_conf.sc_siumcr = (immap->im_siu_conf.sc_siumcr |
SIUMCR_APPC10);
#else
immap->im_siu_conf.sc_siumcr = 0x88000000;
#endif
#endif
#else
/*
* Setting required to enable IRQ1-IRQ7 (SIUMCR [DPPC]),
@ -288,6 +304,7 @@ void pci_mpc8250_init (struct pci_controller *hose)
SIUMCR_CS10PC01 |
SIUMCR_APPC10;
#endif
printf("%s siumcr: %x\n", __FUNCTION__, immap->im_siu_conf.sc_siumcr);
/* Make PCI lowest priority */
/* Each 4 bits is a device bus request and the MS 4bits

View file

@ -25,6 +25,10 @@
#include <mpc8260.h>
#include <asm/processor.h>
#if defined(CONFIG_BOARD_GET_CPU_CLK_F)
extern unsigned long board_get_cpu_clk_f (void);
#endif
DECLARE_GLOBAL_DATA_PTR;
/* ------------------------------------------------------------------------- */
@ -111,8 +115,12 @@ int get_clocks (void)
#if !defined(CONFIG_8260_CLKIN)
#error clock measuring not implemented yet - define CONFIG_8260_CLKIN
#else
#if defined(CONFIG_BOARD_GET_CPU_CLK_F)
clkin = board_get_cpu_clk_f ();
#else
clkin = CONFIG_8260_CLKIN;
#endif
#endif
sccr = immap->im_clkrst.car_sccr;

View file

@ -156,7 +156,7 @@ void board_nand_select_device(struct nand_chip *nand, int chip)
out32(base + NDFC_CCR, 0x00000000 | (cs << 24));
}
void board_nand_init(struct nand_chip *nand)
int board_nand_init(struct nand_chip *nand)
{
int cs = (ulong)nand->IO_ADDR_W & 0x00000003;
ulong base = (ulong)nand->IO_ADDR_W & 0xfffffffc;
@ -188,6 +188,7 @@ void board_nand_init(struct nand_chip *nand)
*/
board_nand_select_device(nand, cs);
out32(base + NDFC_BCFG0 + (cs << 2), 0x80002222);
return 0;
}
#endif

View file

@ -104,6 +104,7 @@
#define FLASH_OFFSET_DEVICE_ID2 0x0E
#define FLASH_OFFSET_DEVICE_ID3 0x0F
#define FLASH_OFFSET_CFI 0x55
#define FLASH_OFFSET_CFI_ALT 0x555
#define FLASH_OFFSET_CFI_RESP 0x10
#define FLASH_OFFSET_PRIMARY_VENDOR 0x13
#define FLASH_OFFSET_EXT_QUERY_T_P_ADDR 0x15 /* extended query table primary addr */
@ -154,6 +155,8 @@ typedef union {
#define NUM_ERASE_REGIONS 4 /* max. number of erase regions */
static uint flash_offset_cfi[2]={FLASH_OFFSET_CFI,FLASH_OFFSET_CFI_ALT};
/* use CFG_MAX_FLASH_BANKS_DETECT if defined */
#ifdef CFG_MAX_FLASH_BANKS_DETECT
static ulong bank_base[CFG_MAX_FLASH_BANKS_DETECT] = CFG_FLASH_BANKS_LIST;
@ -343,7 +346,7 @@ unsigned long flash_init (void)
if (flash_info[i].flash_id == FLASH_UNKNOWN) {
#ifndef CFG_FLASH_QUIET_TEST
printf ("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",
i, flash_info[i].size, flash_info[i].size << 20);
i+1, flash_info[i].size, flash_info[i].size << 20);
#endif /* CFG_FLASH_QUIET_TEST */
}
#ifdef CFG_FLASH_PROTECTION
@ -1136,6 +1139,7 @@ static void flash_read_jedec_ids (flash_info_t * info)
*/
static int flash_detect_cfi (flash_info_t * info)
{
int cfi_offset;
debug ("flash detect cfi\n");
for (info->portwidth = CFG_FLASH_CFI_WIDTH;
@ -1144,19 +1148,22 @@ static int flash_detect_cfi (flash_info_t * info)
info->chipwidth <= info->portwidth;
info->chipwidth <<= 1) {
flash_write_cmd (info, 0, 0, info->cmd_reset);
flash_write_cmd (info, 0, FLASH_OFFSET_CFI, FLASH_CMD_CFI);
if (flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP, 'Q')
&& flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 1, 'R')
&& flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 2, 'Y')) {
info->interface = flash_read_ushort (info, 0, FLASH_OFFSET_INTERFACE);
debug ("device interface is %d\n",
info->interface);
debug ("found port %d chip %d ",
info->portwidth, info->chipwidth);
debug ("port %d bits chip %d bits\n",
info->portwidth << CFI_FLASH_SHIFT_WIDTH,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
return 1;
for (cfi_offset=0; cfi_offset < sizeof(flash_offset_cfi)/sizeof(uint); cfi_offset++) {
flash_write_cmd (info, 0, flash_offset_cfi[cfi_offset], FLASH_CMD_CFI);
if (flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP, 'Q')
&& flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 1, 'R')
&& flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 2, 'Y')) {
info->interface = flash_read_ushort (info, 0, FLASH_OFFSET_INTERFACE);
info->cfi_offset=flash_offset_cfi[cfi_offset];
debug ("device interface is %d\n",
info->interface);
debug ("found port %d chip %d ",
info->portwidth, info->chipwidth);
debug ("port %d bits chip %d bits\n",
info->portwidth << CFI_FLASH_SHIFT_WIDTH,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
return 1;
}
}
}
}
@ -1193,7 +1200,7 @@ ulong flash_get_size (ulong base, int banknum)
info->vendor = flash_read_ushort (info, 0,
FLASH_OFFSET_PRIMARY_VENDOR);
flash_read_jedec_ids (info);
flash_write_cmd (info, 0, FLASH_OFFSET_CFI, FLASH_CMD_CFI);
flash_write_cmd (info, 0, info->cfi_offset, FLASH_CMD_CFI);
num_erase_regions = flash_read_uchar (info,
FLASH_OFFSET_NUM_ERASE_REGIONS);
info->ext_addr = flash_read_ushort (info, 0,

View file

@ -39,7 +39,7 @@ static ulong base_address[CFG_MAX_NAND_DEVICE] = CFG_NAND_BASE_LIST;
static const char default_nand_name[] = "nand";
extern void board_nand_init(struct nand_chip *nand);
extern int board_nand_init(struct nand_chip *nand);
static void nand_init_chip(struct mtd_info *mtd, struct nand_chip *nand,
ulong base_addr)
@ -47,13 +47,16 @@ static void nand_init_chip(struct mtd_info *mtd, struct nand_chip *nand,
mtd->priv = nand;
nand->IO_ADDR_R = nand->IO_ADDR_W = (void __iomem *)base_addr;
board_nand_init(nand);
if (nand_scan(mtd, 1) == 0) {
if (!mtd->name)
mtd->name = (char *)default_nand_name;
} else
if (board_nand_init(nand) == 0) {
if (nand_scan(mtd, 1) == 0) {
if (!mtd->name)
mtd->name = (char *)default_nand_name;
} else
mtd->name = NULL;
} else {
mtd->name = NULL;
mtd->size = 0;
}
}

754
include/configs/TQM8272.h Normal file
View file

@ -0,0 +1,754 @@
/*
* (C) Copyright 2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */
#define CONFIG_MPC8272_FAMILY 1
#define CONFIG_TQM8272 1
#define CONFIG_GET_CPU_STR_F 1 /* Get the CPU ID STR */
#define CONFIG_BOARD_GET_CPU_CLK_F 1 /* Get the CLKIN from board fct */
#define STK82xx_150 1 /* on a STK82xx.150 */
#define CONFIG_CPM2 1 /* Has a CPM2 */
#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_BOARD_EARLY_INIT_R 1
#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
#define CONFIG_BAUDRATE 230400
#else
#define CONFIG_BAUDRATE 115200
#endif
#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consdev=ttyCPM0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"hostname=tqm8272\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addcons=setenv bootargs ${bootargs} " \
"console=$(consdev),$(baudrate)\0" \
"flash_nfs=run nfsargs addip addcons;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addcons;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 300000 ${bootfile};" \
"run nfsargs addip addcons;bootm\0" \
"rootpath=/opt/eldk/ppc_82xx\0" \
"bootfile=/tftpboot/tqm8272/uImage\0" \
"kernel_addr=40080000\0" \
"ramdisk_addr=40100000\0" \
"load=tftp 300000 /tftpboot/tqm8272/u-boot.bin\0" \
"update=protect off 40000000 4003ffff;era 40000000 4003ffff;" \
"cp.b 300000 40000000 40000;" \
"setenv filesize;saveenv\0" \
"cphwib=cp.b 4003fc00 33fc00 400\0" \
"upd=run load;run cphwib;run update\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#define CONFIG_I2C 1
#if CONFIG_I2C
/* enable I2C and select the hardware/software driver */
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
#define ADD_CMD_I2C CFG_CMD_I2C | \
CFG_CMD_DATE |\
CFG_CMD_DTT |\
CFG_CMD_EEPROM
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
/*
* Software (bit-bang) I2C driver configuration
*/
#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
#define I2C_ACTIVE (iop->pdir |= 0x00010000)
#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
#define I2C_READ ((iop->pdat & 0x00010000) != 0)
#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
else iop->pdat &= ~0x00010000
#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
else iop->pdat &= ~0x00020000
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#define CONFIG_I2C_X
/* EEPROM */
#define CFG_I2C_EEPROM_ADDR_LEN 2
#define CFG_EEPROM_PAGE_WRITE_BITS 4
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE /* necessary for the LM75 chip */
#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */
/* I2C RTC */
#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */
#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/* I2C SYSMON (LM75) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
#define CFG_DTT_MAX_TEMP 70
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
#else
#undef CONFIG_HARD_I2C
#undef CONFIG_SOFT_I2C
#define ADD_CMD_I2C 0
#endif
/*
* select serial console configuration
*
* if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
* for SCC).
*
* if CONFIG_CONS_NONE is defined, then the serial console routines must
* defined elsewhere (for example, on the cogent platform, there are serial
* ports on the motherboard which are used for the serial console - see
* cogent/cma101/serial.[ch]).
*/
#define CONFIG_CONS_ON_SMC /* define if console on SMC */
#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
#undef CONFIG_CONS_NONE /* define if console on something else*/
#ifdef CONFIG_82xx_CONS_SMC1
#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
#endif
#ifdef CONFIG_82xx_CONS_SMC2
#define CONFIG_CONS_INDEX 2 /* which serial channel for console */
#endif
#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */
#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */
#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9 */
/*
* select ethernet configuration
*
* if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
* CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
* for FCC)
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
* defined elsewhere (as for the console), or CFG_CMD_NET must be removed
* from CONFIG_COMMANDS to remove support for networking.
*
* (On TQM8272 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the
* X.29 connector, and FCC2 is hardwired to the X.1 connector)
*/
#define CFG_FCC_ETHERNET
#if defined(CFG_FCC_ETHERNET)
#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
#undef CONFIG_ETHER_NONE /* define if ether on something else */
#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */
#else
#define CONFIG_ETHER_ON_SCC /* define if ether on SCC */
#undef CONFIG_ETHER_ON_FCC /* define if ether on FCC */
#undef CONFIG_ETHER_NONE /* define if ether on something else */
#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
#endif
#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1)
/*
* - RX clk is CLK11
* - TX clk is CLK12
*/
# define CFG_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12)
#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
/*
* - Rx-CLK is CLK13
* - Tx-CLK is CLK14
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
* - Enable Full Duplex in FSMR
*/
# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
# define CFG_CPMFCR_RAMTYPE 0
# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
#define CONFIG_MII /* MII PHY management */
#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
/*
* GPIO pins used for bit-banged MII communications
*/
#define MDIO_PORT 2 /* Port C */
#if STK82xx_150
#define CFG_MDIO_PIN 0x00008000 /* PC16 */
#define CFG_MDC_PIN 0x00004000 /* PC17 */
#endif
#if STK82xx_100
#define CFG_MDIO_PIN 0x00000002 /* PC30 */
#define CFG_MDC_PIN 0x00000001 /* PC31 */
#endif
#if 1
#define MDIO_ACTIVE (iop->pdir |= CFG_MDIO_PIN)
#define MDIO_TRISTATE (iop->pdir &= ~CFG_MDIO_PIN)
#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0)
#define MDIO(bit) if(bit) iop->pdat |= CFG_MDIO_PIN; \
else iop->pdat &= ~CFG_MDIO_PIN
#define MDC(bit) if(bit) iop->pdat |= CFG_MDC_PIN; \
else iop->pdat &= ~CFG_MDC_PIN
#else
#define MDIO_ACTIVE ({unsigned long tmp; tmp = iop->pdir; tmp |= CFG_MDIO_PIN; iop->pdir = tmp;})
#define MDIO_TRISTATE ({unsigned long tmp; tmp = iop->pdir; tmp &= ~CFG_MDIO_PIN; iop->pdir = tmp;})
#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0)
#define MDIO(bit) if(bit) {unsigned long tmp; tmp = iop->pdat; tmp |= CFG_MDIO_PIN; iop->pdat = tmp;}\
else {unsigned long tmp; tmp = iop->pdat; tmp &= ~CFG_MDIO_PIN; iop->pdat = tmp;}
#define MDC(bit) if(bit) {unsigned long tmp; tmp = iop->pdat; tmp |= CFG_MDC_PIN; iop->pdat = tmp;}\
else {unsigned long tmp; tmp = iop->pdat; tmp &= ~CFG_MDC_PIN; iop->pdat = tmp;}
#endif
#define MIIDELAY udelay(1)
/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
#define CONFIG_8260_CLKIN 66666666 /* in Hz */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_NAND | \
CFG_CMD_DHCP | \
CFG_CMD_PING | \
ADD_CMD_I2C | \
CFG_CMD_NFS | \
CFG_CMD_MII | \
CFG_CMD_PCI | \
CFG_CMD_SNTP )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if 0
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_LOAD_ADDR 0x300000 /* default load address */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CFG_RESET_ADDRESS 0x40000104 /* "bad" address */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* CAN stuff
*-----------------------------------------------------------------------
*/
#define CFG_CAN_BASE 0x51000000
#define CFG_CAN_SIZE 1
#define CFG_CAN_BR ((CFG_CAN_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_MS_UPMC |\
BRx_V)
#define CFG_CAN_OR (MEG_TO_AM(CFG_CAN_SIZE) |\
ORxU_BI)
/* What should the base address of the main FLASH be and how big is
* it (in MBytes)? This must contain TEXT_BASE from board/tqm8272/config.mk
* The main FLASH is whichever is connected to *CS0.
*/
#define CFG_FLASH0_BASE 0x40000000
#define CFG_FLASH0_SIZE 32 /* 32 MB */
/* Flash bank size (for preliminary settings)
*/
#define CFG_FLASH_SIZE CFG_FLASH0_SIZE
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
#define CFG_FLASH_CFI /* flash is CFI compat. */
#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */
#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/
#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
#define CFG_UPDATE_FLASH_SIZE
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x40000)
#define CFG_ENV_SIZE 0x20000
#define CFG_ENV_SECT_SIZE 0x20000
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SIZE)
#define CFG_ENV_SIZE_REDUND 0x20000
/* Where is the Hardwareinformation Block (from Monitor Sources) */
#define MON_RES_LENGTH (0x0003FC00)
#define HWIB_INFO_START_ADDR (CFG_FLASH_BASE + MON_RES_LENGTH)
#define HWIB_INFO_LEN 512
#define CIB_INFO_START_ADDR (CFG_FLASH_BASE + MON_RES_LENGTH + HWIB_INFO_LEN)
#define CIB_INFO_LEN 512
#define CFG_HWINFO_OFFSET 0x3fc00 /* offset of HW Info block */
#define CFG_HWINFO_SIZE 0x00000060 /* size of HW Info block */
#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
/*-----------------------------------------------------------------------
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
#define CFG_NAND_CS_DIST 0x80
#define CFG_NAND_UPM_WRITE_CMD_OFS 0x20
#define CFG_NAND_UPM_WRITE_ADDR_OFS 0x40
#define CFG_NAND_BR ((CFG_NAND0_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_MS_UPMB |\
BRx_V)
#define CFG_NAND_OR (MEG_TO_AM(CFG_NAND_SIZE) |\
ORxU_BI |\
ORxU_EHTR_8IDLE)
#define CFG_NAND_SIZE 1
#define CFG_NAND0_BASE 0x50000000
#define CFG_NAND1_BASE (CFG_NAND0_BASE + CFG_NAND_CS_DIST)
#define CFG_NAND2_BASE (CFG_NAND1_BASE + CFG_NAND_CS_DIST)
#define CFG_NAND3_BASE (CFG_NAND2_BASE + CFG_NAND_CS_DIST)
#define CFG_MAX_NAND_DEVICE 4 /* Max number of NAND devices */
#define NAND_MAX_CHIPS 1
#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \
CFG_NAND1_BASE, \
CFG_NAND2_BASE, \
CFG_NAND3_BASE, \
}
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)(adr)) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)(adr)))
#define WRITE_NAND_UPM(d, adr, off) do \
{ \
volatile unsigned char *addr = (unsigned char *) (adr + off); \
WRITE_NAND(d, addr); \
} while(0)
#endif /* CFG_CMD_NAND */
#define CONFIG_PCI
#ifdef CONFIG_PCI
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_PCI_PNP
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_PCI_SCAN_SHOW
#endif
/*-----------------------------------------------------------------------
* Hard Reset Configuration Words
*
* if you change bits in the HRCW, you must also change the CFG_*
* defines for the various registers affected by the HRCW e.g. changing
* HRCW_DPPCxx requires you to also change CFG_SIUMCR.
*/
#if 0
#define __HRCW__ALL__ (HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
# define CFG_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111)
#else
#define CFG_HRCW_MASTER (HRCW_BPS11 | HRCW_ISB111 | HRCW_BMS | HRCW_MODCK_H0111)
#endif
/* no slaves so just fill with zeros */
#define CFG_HRCW_SLAVE1 0
#define CFG_HRCW_SLAVE2 0
#define CFG_HRCW_SLAVE3 0
#define CFG_HRCW_SLAVE4 0
#define CFG_HRCW_SLAVE5 0
#define CFG_HRCW_SLAVE6 0
#define CFG_HRCW_SLAVE7 0
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CFG_IMMR 0xFFF00000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
#define CFG_INIT_RAM_END 0x2000 /* End of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE CFG_FLASH0_BASE
#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/
#define BOOTFLAG_WARM 0x02 /* Software reboot */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* HIDx - Hardware Implementation-dependent Registers 2-11
*-----------------------------------------------------------------------
* HID0 also contains cache control - initially enable both caches and
* invalidate contents, then the final state leaves only the instruction
* cache enabled. Note that Power-On and Hard reset invalidate the caches,
* but Soft reset does not.
*
* HID1 has only read-only information - nothing to set.
*/
#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
HID0_IFEM|HID0_ABE)
#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE)
#define CFG_HID2 0
/*-----------------------------------------------------------------------
* RMR - Reset Mode Register 5-5
*-----------------------------------------------------------------------
* turn on Checkstop Reset Enable
*/
#define CFG_RMR RMR_CSRE
/*-----------------------------------------------------------------------
* BCR - Bus Configuration 4-25
*-----------------------------------------------------------------------
*/
#define CFG_BCR_60x (BCR_EBM|BCR_NPQM0|BCR_NPQM2) /* 60x mode */
#define BCR_APD01 0x10000000
#define CFG_BCR_SINGLE (BCR_APD01|BCR_ETM) /* 8260 mode */
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 4-31
*-----------------------------------------------------------------------
*/
#if defined(CONFIG_BOARD_GET_CPU_CLK_F)
#define CFG_SIUMCR_LOW (SIUMCR_DPPC00)
#define CFG_SIUMCR_HIGH (SIUMCR_DPPC00 | SIUMCR_ABE)
#else
#define CFG_SIUMCR (SIUMCR_DPPC00)
#endif
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 4-35
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
*/
#if defined(CONFIG_WATCHDOG)
#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
#else
#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
SYPCR_SWRI|SYPCR_SWP)
#endif /* CONFIG_WATCHDOG */
/*-----------------------------------------------------------------------
* TMCNTSC - Time Counter Status and Control 4-40
*-----------------------------------------------------------------------
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
* and enable Time Counter
*/
#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 4-42
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
* Periodic timer
*/
#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
/*-----------------------------------------------------------------------
* SCCR - System Clock Control 9-8
*-----------------------------------------------------------------------
* Ensure DFBRG is Divide by 16
*/
#define CFG_SCCR SCCR_DFBRG01
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration 13-7
*-----------------------------------------------------------------------
*/
#define CFG_RCCR 0
/*
* Init Memory Controller:
*
* Bank Bus Machine PortSz Device
* ---- --- ------- ------ ------
* 0 60x GPCM 32 bit FLASH
* 1 60x SDRAM 64 bit SDRAM
* 2 60x UPMB 8 bit NAND
* 3 60x UPMC 8 bit CAN
*
*/
/* Initialize SDRAM
*/
#undef CFG_INIT_LOCAL_SDRAM /* No SDRAM on Local Bus */
#define SDRAM_MAX_SIZE 0x20000000 /* max. 512 MB */
/* Minimum mask to separate preliminary
* address ranges for CS[0:2]
*/
#define CFG_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */
#define CFG_MPTPR 0x4000
/*-----------------------------------------------------------------------------
* Address for Mode Register Set (MRS) command
*-----------------------------------------------------------------------------
* In fact, the address is rather configuration data presented to the SDRAM on
* its address lines. Because the address lines may be mux'ed externally either
* for 8 column or 9 column devices, some bits appear twice in the 8260's
* address:
*
* | (RFU) | (RFU) | WBL | TM | CL | BT | Burst Length |
* | BA1 BA0 | A12 : A10 | A9 | A8 A7 | A6 : A4 | A3 | A2 : A0 |
* 8 columns mux'ing: | A9 | A10 A21 | A22 : A24 | A25 | A26 : A28 |
* 9 columns mux'ing: | A8 | A20 A21 | A22 : A24 | A25 | A26 : A28 |
* Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 |
*-----------------------------------------------------------------------------
*/
#define CFG_MRS_OFFS 0x00000110
/* Bank 0 - FLASH
*/
#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
BRx_PS_32 |\
BRx_MS_GPCM_P |\
BRx_V)
#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV4 |\
ORxG_SCY_8_CLK |\
ORxG_TRLX)
/* SDRAM on TQM8272 can have either 8 or 9 columns.
* The number affects configuration values.
*/
/* Bank 1 - 60x bus SDRAM
*/
#define CFG_PSRT 0x20 /* Low Value */
/* #define CFG_PSRT 0x10 Fast Value */
#define CFG_LSRT 0x20 /* Local Bus */
#ifndef CFG_RAMBOOT
#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
#define CFG_OR1_PRELIM CFG_OR1_8COL
/* SDRAM initialization values for 8-column chips
*/
#define CFG_OR1_8COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A7 |\
ORxS_NUMR_12)
#define CFG_PSDMR_8COL (PSDMR_PBI |\
PSDMR_SDAM_A15_IS_A5 |\
PSDMR_BSMA_A12_A14 |\
PSDMR_SDA10_PBI1_A8 |\
PSDMR_RFRC_7_CLK |\
PSDMR_PRETOACT_2W |\
PSDMR_ACTTORW_2W |\
PSDMR_LDOTOPRE_1C |\
PSDMR_WRC_2C |\
PSDMR_EAMUX |\
PSDMR_BUFCMD |\
PSDMR_CL_2)
/* SDRAM initialization values for 9-column chips
*/
#define CFG_OR1_9COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A5 |\
ORxS_NUMR_13)
#define CFG_PSDMR_9COL (PSDMR_PBI |\
PSDMR_SDAM_A16_IS_A5 |\
PSDMR_BSMA_A12_A14 |\
PSDMR_SDA10_PBI1_A7 |\
PSDMR_RFRC_7_CLK |\
PSDMR_PRETOACT_2W |\
PSDMR_ACTTORW_2W |\
PSDMR_LDOTOPRE_1C |\
PSDMR_WRC_2C |\
PSDMR_EAMUX |\
PSDMR_BUFCMD |\
PSDMR_CL_2)
#define CFG_OR1_10COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A4 |\
ORxS_NUMR_13)
#define CFG_PSDMR_10COL (PSDMR_PBI |\
PSDMR_SDAM_A17_IS_A5 |\
PSDMR_BSMA_A12_A14 |\
PSDMR_SDA10_PBI1_A4 |\
PSDMR_RFRC_6_CLK |\
PSDMR_PRETOACT_2W |\
PSDMR_ACTTORW_2W |\
PSDMR_LDOTOPRE_1C |\
PSDMR_WRC_2C |\
PSDMR_EAMUX |\
PSDMR_BUFCMD |\
PSDMR_CL_2)
#define PSDMR_RFRC_66MHZ_SINGLE 0x00028000 /* PSDMR[RFRC] at 66 MHz single mode */
#define PSDMR_RFRC_100MHZ_SINGLE 0x00030000 /* PSDMR[RFRC] at 100 MHz single mode */
#define PSDMR_RFRC_133MHZ_SINGLE 0x00030000 /* PSDMR[RFRC] at 133 MHz single mode */
#define PSDMR_RFRC_66MHZ_60X 0x00030000 /* PSDMR[RFRC] at 66 MHz 60x mode */
#define PSDMR_RFRC_100MHZ_60X 0x00028000 /* PSDMR[RFRC] at 100 MHz 60x mode */
#define PSDMR_RFRC_DEFAULT PSDMR_RFRC_133MHZ_SINGLE /* PSDMR[RFRC] default value */
#define PSDMR_PRETOACT_66MHZ_SINGLE 0x00002000 /* PSDMR[PRETOACT] at 66 MHz single mode */
#define PSDMR_PRETOACT_100MHZ_SINGLE 0x00002000 /* PSDMR[PRETOACT] at 100 MHz single mode */
#define PSDMR_PRETOACT_133MHZ_SINGLE 0x00002000 /* PSDMR[PRETOACT] at 133 MHz single mode */
#define PSDMR_PRETOACT_66MHZ_60X 0x00001000 /* PSDMR[PRETOACT] at 66 MHz 60x mode */
#define PSDMR_PRETOACT_100MHZ_60X 0x00001000 /* PSDMR[PRETOACT] at 100 MHz 60x mode */
#define PSDMR_PRETOACT_DEFAULT PSDMR_PRETOACT_133MHZ_SINGLE /* PSDMR[PRETOACT] default value */
#define PSDMR_WRC_66MHZ_SINGLE 0x00000020 /* PSDMR[WRC] at 66 MHz single mode */
#define PSDMR_WRC_100MHZ_SINGLE 0x00000020 /* PSDMR[WRC] at 100 MHz single mode */
#define PSDMR_WRC_133MHZ_SINGLE 0x00000010 /* PSDMR[WRC] at 133 MHz single mode */
#define PSDMR_WRC_66MHZ_60X 0x00000010 /* PSDMR[WRC] at 66 MHz 60x mode */
#define PSDMR_WRC_100MHZ_60X 0x00000010 /* PSDMR[WRC] at 100 MHz 60x mode */
#define PSDMR_WRC_DEFAULT PSDMR_WRC_133MHZ_SINGLE /* PSDMR[WRC] default value */
#define PSDMR_BUFCMD_66MHZ_SINGLE 0x00000000 /* PSDMR[BUFCMD] at 66 MHz single mode */
#define PSDMR_BUFCMD_100MHZ_SINGLE 0x00000000 /* PSDMR[BUFCMD] at 100 MHz single mode */
#define PSDMR_BUFCMD_133MHZ_SINGLE 0x00000004 /* PSDMR[BUFCMD] at 133 MHz single mode */
#define PSDMR_BUFCMD_66MHZ_60X 0x00000000 /* PSDMR[BUFCMD] at 66 MHz 60x mode */
#define PSDMR_BUFCMD_100MHZ_60X 0x00000000 /* PSDMR[BUFCMD] at 100 MHz 60x mode */
#define PSDMR_BUFCMD_DEFAULT PSDMR_BUFCMD_133MHZ_SINGLE /* PSDMR[BUFCMD] default value */
#endif /* CFG_RAMBOOT */
#endif /* __CONFIG_H */

View file

@ -51,6 +51,7 @@ typedef struct {
ushort device_id2; /* extended device id */
ushort ext_addr; /* extended query table address */
ushort cfi_version; /* cfi version */
ushort cfi_offset; /* offset for cfi query */
#endif
} flash_info_t;

View file

@ -35,7 +35,15 @@
#endif
#ifndef CPU_ID_STR
#if defined(CONFIG_MPC8272_FAMILY)
#ifdef CONFIG_MPC8247
#define CPU_ID_STR "MPC8247"
#elif defined CONFIG_MPC8248
#define CPU_ID_STR "MPC8248"
#elif defined CONFIG_MPC8271
#define CPU_ID_STR "MPC8271"
#else
#define CPU_ID_STR "MPC8272"
#endif
#else
#define CPU_ID_STR "MPC8260"
#endif
@ -66,6 +74,7 @@
#define BCR_EXDD 0x00000400 /* External Master Delay Disable*/
#define BCR_ISPS 0x00000010 /* Internal Space Port Size */
/*-----------------------------------------------------------------------
* PPC_ACR - 60x Bus Arbiter Configuration Register 4-28
*/
@ -168,6 +177,7 @@
#define SIUMCR_MMR10 0x00008000 /* - " - */
#define SIUMCR_MMR11 0x0000c000 /* - " - */
#define SIUMCR_LPBSE 0x00002000 /* LocalBus Parity Byte Select Enable*/
#define SIUMCR_ABE 0x00000400 /* Address output buffer impedance*/
/*-----------------------------------------------------------------------
* IMMR - Internal Memory Map Register 4-34

View file

@ -72,6 +72,10 @@
#include <keyboard.h>
#endif
#ifdef CFG_UPDATE_FLASH_SIZE
extern int update_flash_size (int flash_size);
#endif
#if (CONFIG_COMMANDS & CFG_CMD_DOC)
void doc_init (void);
#endif
@ -730,6 +734,13 @@ void board_init_r (gd_t *id, ulong dest_addr)
bd->bi_flashstart = CFG_FLASH_BASE; /* update start of FLASH memory */
bd->bi_flashsize = flash_size; /* size of FLASH memory (final value) */
#if defined(CFG_UPDATE_FLASH_SIZE)
/* Make a update of the Memctrl. */
update_flash_size (flash_size);
#endif
# if defined(CONFIG_PCU_E) || defined(CONFIG_OXC) || defined(CONFIG_RMU)
/* flash mapped at end of memory map */
bd->bi_flashoffset = TEXT_BASE + flash_size;
@ -876,6 +887,7 @@ void board_init_r (gd_t *id, ulong dest_addr)
#endif
#if defined(CONFIG_TQM8xxL) || defined(CONFIG_TQM8260) || \
defined(CONFIG_TQM8272) || \
defined(CONFIG_CCM) || defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
load_sernum_ethaddr ();
#endif