diff --git a/board/samsung/common/Makefile b/board/samsung/common/Makefile
index 5fb01ce783..6cbd90661b 100644
--- a/board/samsung/common/Makefile
+++ b/board/samsung/common/Makefile
@@ -11,4 +11,5 @@ obj-$(CONFIG_MISC_COMMON) += misc.o
 
 ifndef CONFIG_SPL_BUILD
 obj-$(CONFIG_BOARD_COMMON)	+= board.o
+obj-$(CONFIG_EXYNOS5_DT)	+= exynos5-dt.o
 endif
diff --git a/board/samsung/common/exynos5-dt.c b/board/samsung/common/exynos5-dt.c
new file mode 100644
index 0000000000..7d1b88a9b8
--- /dev/null
+++ b/board/samsung/common/exynos5-dt.c
@@ -0,0 +1,362 @@
+/*
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <dwc3-uboot.h>
+#include <fdtdec.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <samsung-usb-phy-uboot.h>
+#include <spi.h>
+#include <usb.h>
+#include <video_bridge.h>
+#include <asm/gpio.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dwmmc.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
+#include <asm/arch/sromc.h>
+#include <power/pmic.h>
+#include <power/max77686_pmic.h>
+#include <power/regulator.h>
+#include <power/s5m8767.h>
+#include <tmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void board_enable_audio_codec(void)
+{
+	int node, ret;
+	struct gpio_desc en_gpio;
+
+	node = fdtdec_next_compatible(gd->fdt_blob, 0,
+		COMPAT_SAMSUNG_EXYNOS5_SOUND);
+	if (node <= 0)
+		return;
+
+	ret = gpio_request_by_name_nodev(gd->fdt_blob, node,
+					 "codec-enable-gpio", 0, &en_gpio,
+					 GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+	if (ret == -FDT_ERR_NOTFOUND)
+		return;
+
+	/* Turn on the GPIO which connects to the codec's "enable" line. */
+	gpio_set_pull(gpio_get_number(&en_gpio), S5P_GPIO_PULL_NONE);
+
+#ifdef CONFIG_SOUND_MAX98095
+	/* Enable MAX98095 Codec */
+	gpio_request(EXYNOS5_GPIO_X17, "max98095_enable");
+	gpio_direction_output(EXYNOS5_GPIO_X17, 1);
+	gpio_set_pull(EXYNOS5_GPIO_X17, S5P_GPIO_PULL_NONE);
+#endif
+}
+
+int exynos_init(void)
+{
+	board_enable_audio_codec();
+
+	return 0;
+}
+
+static int exynos_set_regulator(const char *name, uint uv)
+{
+	struct udevice *dev;
+	int ret;
+
+	ret = regulator_get_by_platname(name, &dev);
+	if (ret) {
+		debug("%s: Cannot find regulator %s\n", __func__, name);
+		return ret;
+	}
+	ret = regulator_set_value(dev, uv);
+	if (ret) {
+		debug("%s: Cannot set regulator %s\n", __func__, name);
+		return ret;
+	}
+
+	return 0;
+}
+
+int exynos_power_init(void)
+{
+	struct udevice *dev;
+	int ret;
+
+	ret = pmic_get("max77686", &dev);
+	if (!ret) {
+		/* TODO(sjg@chromium.org): Move into the clock/pmic API */
+		ret = pmic_clrsetbits(dev, MAX77686_REG_PMIC_32KHZ, 0,
+				MAX77686_32KHCP_EN);
+		if (ret)
+			return ret;
+		ret = pmic_clrsetbits(dev, MAX77686_REG_PMIC_BBAT, 0,
+				MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V);
+		if (ret)
+			return ret;
+	} else {
+		ret = pmic_get("s5m8767-pmic", &dev);
+		/* TODO(sjg@chromium.org): Use driver model to access clock */
+#ifdef CONFIG_PMIC_S5M8767
+		if (!ret)
+			s5m8767_enable_32khz_cp(dev);
+#endif
+	}
+	if (ret == -ENODEV)
+		return 0;
+
+	ret = regulators_enable_boot_on(false);
+	if (ret)
+		return ret;
+
+	ret = exynos_set_regulator("vdd_mif", 1100000);
+	if (ret)
+		return ret;
+
+	/*
+	 * This would normally be 1.3V, but since we are running slowly 1V
+	 * is enough. For spring it helps reduce CPU temperature and avoid
+	 * hangs with the case open.
+	 */
+	ret = exynos_set_regulator("vdd_arm", 1000000);
+	if (ret)
+		return ret;
+	ret = exynos_set_regulator("vdd_int", 1012500);
+	if (ret)
+		return ret;
+	ret = exynos_set_regulator("vdd_g3d", 1200000);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+int board_get_revision(void)
+{
+	return 0;
+}
+
+#ifdef CONFIG_LCD
+
+static int board_dp_bridge_init(struct udevice *dev)
+{
+	const int max_tries = 10;
+	int num_tries;
+	int ret;
+
+	debug("%s\n", __func__);
+	ret = video_bridge_attach(dev);
+	if (ret) {
+		debug("video bridge init failed: %d\n", ret);
+		return ret;
+	}
+
+	/*
+	 * We need to wait for 90ms after bringing up the bridge since there
+	 * is a phantom "high" on the HPD chip during its bootup.  The phantom
+	 * high comes within 7ms of de-asserting PD and persists for at least
+	 * 15ms.  The real high comes roughly 50ms after PD is de-asserted. The
+	 * phantom high makes it hard for us to know when the NXP chip is up.
+	 */
+	mdelay(90);
+
+	for (num_tries = 0; num_tries < max_tries; num_tries++) {
+		/* Check HPD. If it's high, or we don't have it, all is well */
+		ret = video_bridge_check_attached(dev);
+		if (!ret || ret == -ENOENT)
+			return 0;
+
+		debug("%s: eDP bridge failed to come up; try %d of %d\n",
+		      __func__, num_tries, max_tries);
+	}
+
+	/* Immediately go into bridge reset if the hp line is not high */
+	return -EIO;
+}
+
+static int board_dp_bridge_setup(const void *blob)
+{
+	const int max_tries = 2;
+	int num_tries;
+	struct udevice *dev;
+	int ret;
+
+	/* Configure I2C registers for Parade bridge */
+	ret = uclass_get_device(UCLASS_VIDEO_BRIDGE, 0, &dev);
+	if (ret) {
+		debug("video bridge init failed: %d\n", ret);
+		return ret;
+	}
+
+	if (strncmp(dev->driver->name, "parade", 6)) {
+		/* Mux HPHPD to the special hotplug detect mode */
+		exynos_pinmux_config(PERIPH_ID_DPHPD, 0);
+	}
+
+	for (num_tries = 0; num_tries < max_tries; num_tries++) {
+		ret = board_dp_bridge_init(dev);
+		if (!ret)
+			return 0;
+		if (num_tries == max_tries - 1)
+			break;
+
+		/*
+		* If we're here, the bridge chip failed to initialise.
+		* Power down the bridge in an attempt to reset.
+		*/
+		video_bridge_set_active(dev, false);
+
+		/*
+		* Arbitrarily wait 300ms here with DP_N low.  Don't know for
+		* sure how long we should wait, but we're being paranoid.
+		*/
+		mdelay(300);
+	}
+
+	return ret;
+}
+
+void exynos_cfg_lcd_gpio(void)
+{
+	/* For Backlight */
+	gpio_request(EXYNOS5_GPIO_B20, "lcd_backlight");
+	gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT);
+	gpio_set_value(EXYNOS5_GPIO_B20, 1);
+}
+
+void exynos_set_dp_phy(unsigned int onoff)
+{
+	set_dp_phy_ctrl(onoff);
+}
+
+static int board_dp_set_backlight(int percent)
+{
+	struct udevice *dev;
+	int ret;
+
+	ret = uclass_get_device(UCLASS_VIDEO_BRIDGE, 0, &dev);
+	if (!ret)
+		ret = video_bridge_set_backlight(dev, percent);
+
+	return ret;
+}
+
+void exynos_backlight_on(unsigned int on)
+{
+	struct udevice *dev;
+	int ret;
+
+	debug("%s(%u)\n", __func__, on);
+	if (!on)
+		return;
+
+	ret = regulator_get_by_platname("vcd_led", &dev);
+	if (!ret)
+		ret = regulator_set_enable(dev, true);
+	if (ret)
+		debug("Failed to enable backlight: ret=%d\n", ret);
+
+	/* T5 in the LCD timing spec (defined as > 10ms) */
+	mdelay(10);
+
+	/* board_dp_backlight_pwm */
+	gpio_direction_output(EXYNOS5_GPIO_B20, 1);
+
+	/* T6 in the LCD timing spec (defined as > 10ms) */
+	mdelay(10);
+
+	/* try to set the backlight in the bridge registers */
+	ret = board_dp_set_backlight(80);
+
+	/* if we have no bridge or it does not support backlight, use a GPIO */
+	if (ret == -ENODEV || ret == -ENOSYS) {
+		gpio_request(EXYNOS5_GPIO_X30, "board_dp_backlight_en");
+		gpio_direction_output(EXYNOS5_GPIO_X30, 1);
+	}
+}
+
+void exynos_lcd_power_on(void)
+{
+	struct udevice *dev;
+	int ret;
+
+	debug("%s\n", __func__);
+	ret = regulator_get_by_platname("lcd_vdd", &dev);
+	if (!ret)
+		ret = regulator_set_enable(dev, true);
+	if (ret)
+		debug("Failed to enable LCD panel: ret=%d\n", ret);
+
+	ret = board_dp_bridge_setup(gd->fdt_blob);
+	if (ret && ret != -ENODEV)
+		printf("LCD bridge failed to enable: %d\n", ret);
+}
+
+#endif
+
+#ifdef CONFIG_USB_DWC3
+static struct dwc3_device dwc3_device_data = {
+	.maximum_speed = USB_SPEED_SUPER,
+	.base = 0x12400000,
+	.dr_mode = USB_DR_MODE_PERIPHERAL,
+	.index = 0,
+};
+
+int usb_gadget_handle_interrupts(void)
+{
+	dwc3_uboot_handle_interrupt(0);
+	return 0;
+}
+
+int board_usb_init(int index, enum usb_init_type init)
+{
+	struct exynos_usb3_phy *phy = (struct exynos_usb3_phy *)
+		samsung_get_base_usb3_phy();
+
+	if (!phy) {
+		error("usb3 phy not supported");
+		return -ENODEV;
+	}
+
+	set_usbdrd_phy_ctrl(POWER_USB_DRD_PHY_CTRL_EN);
+	exynos5_usb3_phy_init(phy);
+
+	return dwc3_uboot_init(&dwc3_device_data);
+}
+#endif
+#ifdef CONFIG_SET_DFU_ALT_INFO
+char *get_dfu_alt_system(char *interface, char *devstr)
+{
+	return getenv("dfu_alt_system");
+}
+
+char *get_dfu_alt_boot(char *interface, char *devstr)
+{
+	struct mmc *mmc;
+	char *alt_boot;
+	int dev_num;
+
+	dev_num = simple_strtoul(devstr, NULL, 10);
+
+	mmc = find_mmc_device(dev_num);
+	if (!mmc)
+		return NULL;
+
+	if (mmc_init(mmc))
+		return NULL;
+
+	if (IS_SD(mmc))
+		alt_boot = CONFIG_DFU_ALT_BOOT_SD;
+	else
+		alt_boot = CONFIG_DFU_ALT_BOOT_EMMC;
+
+	return alt_boot;
+}
+#endif