arch: arm: mach-k3: am642_init: Probe ESM nodes

On AM64x devices, it is possible to route Main ESM0 error events to MCU
ESM. MCU ESM high error output can trigger the reset logic to reset the
device. So, for these devices we expect two ESM device nodes in the
device tree, one for Main ESM and the another MCU ESM in the device tree.
 When these ESM device nodes are properly configired it is possible to
route the Main RTI0 WWDT output to the MCU ESM high output through Main
ESM and trigger a device reset when
CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RESET_EN_Z is set to '0'.

On K3 AM64x devices, the R5 SPL u-boot handles the ESM device node
configurations.

Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This commit is contained in:
Hari Nagalla 2022-03-09 14:42:30 -06:00 committed by Tom Rini
parent 3d64cffa91
commit 92e46092f2

View file

@ -24,12 +24,22 @@
#include <dm/root.h>
#if defined(CONFIG_SPL_BUILD)
#define MCU_CTRL_MMR0_BASE 0x04500000
#define CTRLMMR_MCU_RST_CTRL 0x04518170
static void ctrl_mmr_unlock(void)
{
/* Unlock all PADCFG_MMR1 module registers */
mmr_unlock(PADCFG_MMR1_BASE, 1);
/* Unlock all MCU_CTRL_MMR0 module registers */
mmr_unlock(MCU_CTRL_MMR0_BASE, 0);
mmr_unlock(MCU_CTRL_MMR0_BASE, 1);
mmr_unlock(MCU_CTRL_MMR0_BASE, 2);
mmr_unlock(MCU_CTRL_MMR0_BASE, 3);
mmr_unlock(MCU_CTRL_MMR0_BASE, 4);
mmr_unlock(MCU_CTRL_MMR0_BASE, 6);
/* Unlock all CTRL_MMR0 module registers */
mmr_unlock(CTRL_MMR0_BASE, 0);
mmr_unlock(CTRL_MMR0_BASE, 1);
@ -37,9 +47,6 @@ static void ctrl_mmr_unlock(void)
mmr_unlock(CTRL_MMR0_BASE, 3);
mmr_unlock(CTRL_MMR0_BASE, 5);
mmr_unlock(CTRL_MMR0_BASE, 6);
/* Unlock all MCU_PADCFG_MMR1 module registers */
mmr_unlock(MCU_PADCFG_MMR1_BASE, 1);
}
/*
@ -142,9 +149,20 @@ int fdtdec_board_setup(const void *fdt_blob)
}
#endif
#if defined(CONFIG_ESM_K3)
static void enable_mcu_esm_reset(void)
{
/* Set CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RST_EN_Z to '0' (low active) */
u32 stat = readl(CTRLMMR_MCU_RST_CTRL);
stat &= 0xFFFDFFFF;
writel(stat, CTRLMMR_MCU_RST_CTRL);
}
#endif
void board_init_f(ulong dummy)
{
#if defined(CONFIG_K3_LOAD_SYSFW) || defined(CONFIG_K3_AM64_DDRSS)
#if defined(CONFIG_K3_LOAD_SYSFW) || defined(CONFIG_K3_AM64_DDRSS) || defined(CONFIG_ESM_K3)
struct udevice *dev;
int ret;
#endif
@ -194,6 +212,20 @@ void board_init_f(ulong dummy)
/* Output System Firmware version info */
k3_sysfw_print_ver();
#if defined(CONFIG_ESM_K3)
/* Probe/configure ESM0 */
ret = uclass_get_device_by_name(UCLASS_MISC, "esm@420000", &dev);
if (ret)
printf("esm main init failed: %d\n", ret);
/* Probe/configure MCUESM */
ret = uclass_get_device_by_name(UCLASS_MISC, "esm@4100000", &dev);
if (ret)
printf("esm mcu init failed: %d\n", ret);
enable_mcu_esm_reset();
#endif
#if defined(CONFIG_K3_AM64_DDRSS)
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
if (ret)