ARM1176: Coexist with other ARM1176 platforms

The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture.  The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.

Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.

1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.

2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM.  Added support for this capability in ARM1176 architecture.

3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.

4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include.  The presence
of this include prevents builds on other ARM1176 archs.

5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

arch/arm/cpu/arm1176/cpu.c

@@ -33,9 +33,6 @@
 
 #include <common.h>
 #include <command.h>
-#ifdef CONFIG_S3C64XX
-#include <asm/arch/s3c6400.h>
-#endif
 #include <asm/system.h>
 
 static void cache_flush (void);

arch/arm/cpu/arm1176/start.S

@@ -1,5 +1,5 @@
 /*
- *  armboot - Startup Code for S3C6400/ARM1176 CPU-core
+ *  armboot - Startup Code for ARM1176 CPU-core
  *
  * Copyright (c) 2007	Samsung Electronics
  *
@@ -35,9 +35,6 @@
 #ifdef CONFIG_ENABLE_MMU
 #include <asm/proc/domain.h>
 #endif
-#ifdef CONFIG_S3C64XX
-#include <asm/arch/s3c6400.h>
-#endif
 
 #if !defined(CONFIG_ENABLE_MMU) && !defined(CONFIG_SYS_PHY_UBOOT_BASE)
 #define CONFIG_SYS_PHY_UBOOT_BASE	CONFIG_SYS_UBOOT_BASE
@@ -172,14 +169,10 @@ cpu_init_crit:
 	bic	r0, r0, #0x00000087	@ clear bits 7, 2:0 (B--- -CAM)
 	orr	r0, r0, #0x00000002	@ set bit 2 (A) Align
 	orr	r0, r0, #0x00001000	@ set bit 12 (I) I-Cache
+
 	/* Prepare to disable the MMU */
-	adr	r1, mmu_disable_phys
+	adr	r2, mmu_disable_phys
-	/* We presume we're within the first 1024 bytes */
+	sub	r2, r2, #(CONFIG_SYS_PHY_UBOOT_BASE - TEXT_BASE)
-	and	r1, r1, #0x3fc
-	ldr	r2, _TEXT_PHY_BASE
-	ldr	r3, =0xfff00000
-	and	r2, r2, r3
-	orr	r2, r2, r1
 	b	mmu_disable
 
 	.align 5
@@ -189,14 +182,30 @@ mmu_disable:
 	nop
 	nop
 	mov	pc, r2
+mmu_disable_phys:
+
+#ifdef CONFIG_DISABLE_TCM
+	/*
+	 * Disable the TCMs
+	 */
+	mrc	p15, 0, r0, c0, c0, 2	/* Return TCM details */
+	cmp	r0, #0
+	beq	skip_tcmdisable
+	mov	r1, #0
+	mov	r2, #1
+	tst	r0, r2
+	mcrne	p15, 0, r1, c9, c1, 1	/* Disable Instruction TCM if present*/
+	tst	r0, r2, LSL #16
+	mcrne	p15, 0, r1, c9, c1, 0	/* Disable Data TCM if present*/
+skip_tcmdisable:
+#endif
 #endif
 
-mmu_disable_phys:
+#ifdef CONFIG_PERIPORT_REMAP
-#ifdef CONFIG_S3C64XX
 	/* Peri port setup */
-	ldr	r0, =0x70000000
+	ldr	r0, =CONFIG_PERIPORT_BASE
-	orr	r0, r0, #0x13
+	orr	r0, r0, #CONFIG_PERIPORT_SIZE
-	mcr	p15,0,r0,c15,c2,4       @ 256M (0x70000000 - 0x7fffffff)
+	mcr	p15,0,r0,c15,c2,4
 #endif
 
 	/*
@@ -204,7 +213,25 @@ mmu_disable_phys:
 	 */
 	bl	lowlevel_init		/* go setup pll,mux,memory */
 
-after_copy:
+#ifndef CONFIG_SKIP_RELOCATE_UBOOT
+relocate:				/* relocate U-Boot to RAM	    */
+	adr	r0, _start		/* r0 <- current position of code   */
+	ldr	r1, _TEXT_BASE		/* test if we run from flash or RAM */
+	cmp     r0, r1                  /* don't reloc during debug         */
+	beq     stack_setup
+
+	ldr	r2, _armboot_start
+	ldr	r3, _bss_start
+	sub	r2, r3, r2		/* r2 <- size of armboot            */
+	add	r2, r0, r2		/* r2 <- source end address         */
+
+copy_loop:
+	ldmia	r0!, {r3-r10}		/* copy from source address [r0]    */
+	stmia	r1!, {r3-r10}		/* copy to   target address [r1]    */
+	cmp	r0, r2			/* until source end addreee [r2]    */
+	ble	copy_loop
+#endif	/* CONFIG_SKIP_RELOCATE_UBOOT */
+
 #ifdef CONFIG_ENABLE_MMU
 enable_mmu:
 	/* enable domain access */
@@ -240,9 +267,9 @@ mmu_enable:
 	nop
 	nop
 	mov	pc, r2
+skip_hw_init:
 #endif
 
-skip_hw_init:
 	/* Set up the stack						    */
 stack_setup:
 	ldr	r0, =CONFIG_SYS_UBOOT_BASE	/* base of copy in DRAM	    */
@@ -310,6 +337,8 @@ phy_last_jump:
 	mov	r0, #0
 	mov	pc, r9
 #endif
+
+
 /*
  *************************************************************************
  *

include/configs/smdk6400.h

@@ -40,6 +40,12 @@
 #define CONFIG_S3C64XX		1	/* in a SAMSUNG S3C64XX Family  */
 #define CONFIG_SMDK6400		1	/* on a SAMSUNG SMDK6400 Board  */
 
+#define CONFIG_SKIP_RELOCATE_UBOOT
+
+#define CONFIG_PERIPORT_REMAP
+#define CONFIG_PERIPORT_BASE	0x70000000
+#define CONFIG_PERIPORT_SIZE	0x13
+
 #define CONFIG_SYS_SDRAM_BASE	0x50000000
 
 /* input clock of PLL: SMDK6400 has 12MHz input clock */
@@ -61,8 +67,6 @@
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
 
-#undef CONFIG_SKIP_RELOCATE_UBOOT
-
 /*
  * Size of malloc() pool
  */