Merge branch 'denx'

CREDITS

@@ -405,7 +405,8 @@ D: Atmel AT91CAP9ADK support
 
 N: Ricardo Ribalda Delgado
 E: ricardo.ribalda@uam.es
-D: PPC440x5 (Virtex5), ML507 Board, eeprom_simul, adt7460
+D: PPC440x5 (Virtex5), ML507 Board, eeprom_simul, adt7460, v5fx30teval
+D: Virtex ppc440 generic architecture
 W: http://www.ii.uam.es/~rribalda
 
 N: Stefan Roese

MAINTAINERS

@@ -314,6 +314,8 @@ Daniel Poirot <dan.poirot@windriver.com>
 Ricardo Ribalda <ricardo.ribalda@uam.es>
 
 	ml507 		PPC440x5
+	v5fx30teval	PPC440x5
+	xilinx-pp440-generic	PPC440x5
 
 Stefan Roese <sr@denx.de>
 

MAKEALL

@@ -230,12 +230,16 @@ LIST_4xx="		\
 	sequoia_nand	\
 	taihu		\
 	taishan		\
+	v5fx30teval	\
+	v5fx30teval_flash \
 	VOH405		\
 	VOM405		\
 	W7OLMC		\
 	W7OLMG		\
 	walnut		\
 	WUH405		\
+	xilinx-ppc440-generic \
+	xilinx-ppc440-generic_flash \
 	XPEDITE1K	\
 	yellowstone	\
 	yosemite	\

Makefile

@@ -295,7 +295,7 @@ $(obj)u-boot.hex:	$(obj)u-boot
 		$(OBJCOPY) ${OBJCFLAGS} -O ihex $< $@
 
 $(obj)u-boot.srec:	$(obj)u-boot
-		$(OBJCOPY) ${OBJCFLAGS} -O srec $< $@
+		$(OBJCOPY) -O srec $< $@
 
 $(obj)u-boot.bin:	$(obj)u-boot
 		$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
@@ -1242,12 +1242,15 @@ CMS700_config:	unconfig
 CPCI2DP_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx cpci2dp esd
 
-CPCI405_config	\
+CPCI405_config:		unconfig
+	@$(MKCONFIG) $(@:_config=) ppc ppc4xx cpci405 esd
+
 CPCI4052_config		\
 CPCI405DT_config	\
 CPCI405AB_config:	unconfig
+	@mkdir -p $(obj)board/esd/cpci405
+	@echo "TEXT_BASE = 0xFFFC0000" > $(obj)board/esd/cpci405/config.tmp
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx cpci405 esd
-	@echo "BOARD_REVISION = $(@:_config=)"	>> $(obj)include/config.mk
 
 CPCIISER4_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx cpciiser4 esd
@@ -1357,15 +1360,22 @@ ml300_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx ml300 xilinx
 
 ml507_flash_config: unconfig
+	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
 	@mkdir -p $(obj)include $(obj)board/xilinx/ml507
-	@cp $(obj)board/xilinx/ml507/u-boot-rom.lds  $(obj)board/xilinx/ml507/u-boot.lds
+	@echo "LDSCRIPT:=$(SRCTREE)/board/xilinx/ppc440-generic/u-boot-rom.lds"\
-	@echo "TEXT_BASE = 0xFE360000" > $(obj)board/xilinx/ml507/config.tmp
+		> $(obj)board/xilinx/ml507/config.tmp
-	@$(MKCONFIG) $(@:_flash_config=) ppc ppc4xx ml507 xilinx
+	@echo "TEXT_BASE := 0xFE360000" \
+		>> $(obj)board/xilinx/ml507/config.tmp
+	@$(MKCONFIG) ml507 ppc ppc4xx ml507 xilinx
 
 ml507_config: unconfig
+	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
 	@mkdir -p $(obj)include $(obj)board/xilinx/ml507
-	@cp $(obj)board/xilinx/ml507/u-boot-ram.lds  $(obj)board/xilinx/ml507/u-boot.lds
+	@echo "LDSCRIPT:=$(SRCTREE)/board/xilinx/ppc440-generic/u-boot-ram.lds"\
-	@$(MKCONFIG) $(@:_config=) ppc ppc4xx ml507 xilinx
+		> $(obj)board/xilinx/ml507/config.tmp
+	@echo "TEXT_BASE := 0x04000000"  \
+		>> $(obj)board/xilinx/ml507/config.tmp
+	@$(MKCONFIG) ml507 ppc ppc4xx ml507 xilinx
 
 ocotea_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx ocotea amcc
@@ -1461,6 +1471,24 @@ taihu_config:	unconfig
 taishan_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx taishan amcc
 
+v5fx30teval_config: unconfig
+	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
+	@mkdir -p $(obj)include $(obj)board/avnet/v5fx30teval
+	@echo "LDSCRIPT:=$(SRCTREE)/board/xilinx/ppc440-generic/u-boot-ram.lds"\
+		> $(obj)board/avnet/v5fx30teval/config.tmp
+	@echo "TEXT_BASE := 0x03000000" \
+		>> $(obj)board/avnet/v5fx30teval/config.tmp
+	@$(MKCONFIG) v5fx30teval ppc ppc4xx v5fx30teval avnet
+
+v5fx30teval_flash_config: unconfig
+	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
+	@mkdir -p $(obj)include $(obj)board/avnet/v5fx30teval
+	@echo "LDSCRIPT:=$(SRCTREE)/board/xilinx/ppc440-generic/u-boot-rom.lds"\
+		> $(obj)/board/avnet/v5fx30teval/config.tmp
+	@echo "TEXT_BASE := 0xFF1C0000" \
+		>> $(obj)/board/avnet/v5fx30teval/config.tmp
+	@$(MKCONFIG) v5fx30teval ppc ppc4xx v5fx30teval avnet
+
 VOH405_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx voh405 esd
 
@@ -1479,6 +1507,22 @@ sycamore_config: unconfig
 WUH405_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx wuh405 esd
 
+xilinx-ppc440-generic_flash_config: unconfig
+	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
+	@echo "LDSCRIPT:=$(SRCTREE)/board/xilinx/ppc440-generic/u-boot-rom.lds"\
+		> $(obj)board/xilinx/ppc440-generic/config.tmp
+	@echo "TEXT_BASE := 0xFE360000" \
+		>> $(obj)board/xilinx/ppc440-generic/config.tmp
+	@$(MKCONFIG) xilinx-ppc440-generic ppc ppc4xx ppc440-generic xilinx
+
+xilinx-ppc440-generic_config: unconfig
+	@mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic
+	@echo "LDSCRIPT:=$(SRCTREE)/board/xilinx/ppc440-generic/u-boot-ram.lds"\
+		> $(obj)board/xilinx/ppc440-generic/config.tmp
+	@echo "TEXT_BASE := 0x04000000" \
+		>> $(obj)board/xilinx/ppc440-generic/config.tmp
+	@$(MKCONFIG) xilinx-ppc440-generic ppc ppc4xx ppc440-generic xilinx
+
 XPEDITE1K_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx xpedite1k
 

README

@@ -380,11 +380,11 @@ The following options need to be configured:
 		param header, the default value is zero if undefined.
 
 - Serial Ports:
-		CFG_PL010_SERIAL
+		CONFIG_PL010_SERIAL
 
 		Define this if you want support for Amba PrimeCell PL010 UARTs.
 
-		CFG_PL011_SERIAL
+		CONFIG_PL011_SERIAL
 
 		Define this if you want support for Amba PrimeCell PL011 UARTs.
 
@@ -3030,8 +3030,9 @@ details; basically, the header defines the following image properties:
 
 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
   4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
-  LynxOS, pSOS, QNX, RTEMS, ARTOS;
+  LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
-  Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
+  Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
+  INTEGRITY).
 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
   IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
   Currently supported: ARM, AVR32, Intel x86, MIPS, NIOS, PowerPC).
@@ -3089,9 +3090,9 @@ But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
 
 Just make sure your machine specific header file (for instance
 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
-Information structure as we define in include/u-boot.h, and make
+Information structure as we define in include/asm-<arch>/u-boot.h,
-sure that your definition of IMAP_ADDR uses the same value as your
+and make sure that your definition of IMAP_ADDR uses the same value
-U-Boot configuration in CFG_IMMR.
+as your U-Boot configuration in CFG_IMMR.
 
 
 Configuring the Linux kernel:

board/atc/atc.c

@@ -380,7 +380,6 @@ phys_size_t initdram (int board_type)
 }
 
 #if defined(CONFIG_CMD_DOC)
-extern void doc_probe (ulong physadr);
 void doc_init (void)
 {
 	doc_probe (CFG_DOC_BASE);

board/avnet/v5fx30teval/Makefile

@@ -0,0 +1,27 @@
+#
+# (C) Copyright 2008
+# Ricardo Ribalda,Universidad Autonoma de Madrid, ricardo.ribalda@uam.es
+# This work has been supported by: Qtechnology http://qtec.com/
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+COBJS	+= $(BOARD).o
+
+include $(SRCTREE)/board/xilinx/ppc440-generic/Makefile

board/avnet/v5fx30teval/config.mk

@@ -0,0 +1,26 @@
+#
+# (C) Copyright 2008
+# Ricardo Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+# Work supported by Qtechnology http://www.qtec.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+#
+
+sinclude $(SRCTREE)/board/xilinx/ppc440-generic/config.mk

board/avnet/v5fx30teval/v5fx30teval.c

@@ -0,0 +1,28 @@
+/*
+ * (C) Copyright 2008
+ * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+ * This work has been supported by: QTechnology  http://qtec.com/
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <config.h>
+#include <common.h>
+#include <asm/processor.h>
+
+
+int checkboard(void)
+{
+	puts("Avnet Virtex 5 FX30 Evaluation Board\n");
+	return 0;
+}

board/avnet/v5fx30teval/xparameters.h

@@ -0,0 +1,33 @@
+/*
+ * (C) Copyright 2008
+ * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+ * This work has been supported by: QTechnology  http://qtec.com/
+ * based on xparameters.h by Xilinx
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef XPARAMETER_H
+#define XPARAMETER_H
+
+#define XPAR_DDR2_SDRAM_MEM_BASEADDR	0x00000000
+#define XPAR_INTC_0_BASEADDR		0x81800000
+#define XPAR_UARTLITE_0_BASEADDR	0x84000000
+#define XPAR_FLASH_MEM0_BASEADDR	0xFF000000
+#define XPAR_PLB_CLOCK_FREQ_HZ		100000000
+#define XPAR_CORE_CLOCK_FREQ_HZ		400000000
+#define XPAR_INTC_MAX_NUM_INTR_INPUTS	13
+#define XPAR_UARTLITE_0_BAUDRATE	9600
+
+#endif

board/cpu86/cpu86.c

@@ -313,7 +313,6 @@ phys_size_t initdram (int board_type)
 }
 
 #if defined(CONFIG_CMD_DOC)
-extern void doc_probe (ulong physadr);
 void doc_init (void)
 {
 	doc_probe (CFG_DOC_BASE);

board/cpu87/cpu87.c

@@ -323,7 +323,6 @@ phys_size_t initdram (int board_type)
 }
 
 #if defined(CONFIG_CMD_DOC)
-extern void doc_probe (ulong physadr);
 void doc_init (void)
 {
 	doc_probe (CFG_DOC_BASE);

board/esd/cpci405/config.mk

@@ -21,20 +21,8 @@
 # MA 02111-1307 USA
 #
 
-#
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
-# esd CPCI405 boards
-#
 
-ifeq ($(BOARD_REVISION),CPCI4052)
+ifndef TEXT_BASE
-TEXT_BASE = 0xFFFC0000
-else
-ifeq ($(BOARD_REVISION),CPCI405DT)
-TEXT_BASE = 0xFFFC0000
-else
-ifeq ($(BOARD_REVISION),CPCI405AB)
-TEXT_BASE = 0xFFFC0000
-else
 TEXT_BASE = 0xFFFD0000
 endif
-endif
-endif

board/esd/cpci405/u-boot.lds

@@ -57,22 +57,7 @@ SECTIONS
   .plt : { *(.plt) }
   .text      :
   {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-
     cpu/ppc4xx/start.o	(.text)
-    cpu/ppc4xx/traps.o	(.text)
-    cpu/ppc4xx/interrupts.o	(.text)
-    cpu/ppc4xx/4xx_uart.o	(.text)
-    cpu/ppc4xx/cpu_init.o	(.text)
-    cpu/ppc4xx/speed.o	(.text)
-    common/dlmalloc.o	(.text)
-    lib_generic/crc32.o		(.text)
-    lib_ppc/extable.o	(.text)
-    lib_generic/zlib.o		(.text)
-
-/*    . = env_offset;*/
-/*    common/environment.o(.text)*/
 
     *(.text)
     *(.fixup)

board/gen860t/gen860t.c

@@ -223,8 +223,6 @@ phys_size_t initdram (int board_type)
  * The DOC lives in the CS2* space
  */
 #if defined(CONFIG_CMD_DOC)
-extern void doc_probe (ulong physadr);
-
 void doc_init (void)
 {
 	printf ("Probing at 0x%.8x: ", DOC_BASE);

board/integratorcp/integratorcp.c

@@ -34,6 +34,7 @@
  */
 
 #include <common.h>
+#include <div64.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -244,7 +245,11 @@ ulong get_timer_masked (void)
 		total_count += lastdec - now;
 	}
 	lastdec	  = now;
-	timestamp = (ulong)(total_count/div_timer);
+
+	/* Reuse "now" */
+	now = total_count;
+	do_div(now, div_timer);
+	timestamp = now;
 
 	return timestamp;
 }

board/mcc200/mcc200.c

@@ -323,7 +323,6 @@ void ide_set_reset (int idereset)
 #endif
 
 #if defined(CONFIG_CMD_DOC)
-extern void doc_probe (ulong physadr);
 void doc_init (void)
 {
 	doc_probe (CFG_DOC_BASE);

board/mpl/common/common_util.c

@@ -565,7 +565,6 @@ int do_mplcommon(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 
 #if defined(CONFIG_CMD_DOC)
-extern void doc_probe(ulong physadr);
 void doc_init (void)
 {
   doc_probe(MULTI_PURPOSE_SOCKET_ADDR);

board/netstal/hcu5/sdram.c

@@ -122,7 +122,7 @@ void sdram_panic(const char *reason)
 }
 
 #ifdef CONFIG_DDR_ECC
-static void blank_string(int size)
+void blank_string(int size)
 {
 	int i;
 

board/netta2/netta2.c

@@ -620,20 +620,6 @@ void hw_watchdog_reset(void)
 
 #endif
 
-#ifdef CONFIG_SHOW_ACTIVITY
-
-/* called from timer interrupt every 1/CFG_HZ sec */
-void board_show_activity(ulong timestamp)
-{
-}
-
-/* called when looping */
-void show_activity(int arg)
-{
-}
-
-#endif
-
 #if defined(CFG_CONSOLE_IS_IN_ENV) && defined(CFG_CONSOLE_OVERWRITE_ROUTINE)
 int overwrite_console(void)
 {

board/pm520/pm520.c

@@ -316,7 +316,6 @@ void ide_set_reset (int idereset)
 #endif
 
 #if defined(CONFIG_CMD_DOC)
-extern void doc_probe (ulong physadr);
 void doc_init (void)
 {
 	doc_probe (CFG_DOC_BASE);

board/pm826/pm826.c

@@ -312,7 +312,6 @@ phys_size_t initdram (int board_type)
 }
 
 #if defined(CONFIG_CMD_DOC)
-extern void doc_probe (ulong physadr);
 void doc_init (void)
 {
 	doc_probe (CFG_DOC_BASE);

board/pm828/pm828.c

@@ -345,7 +345,6 @@ phys_size_t initdram (int board_type)
 }
 
 #if defined(CONFIG_CMD_DOC)
-extern void doc_probe (ulong physadr);
 void doc_init (void)
 {
 	doc_probe (CFG_DOC_BASE);

board/sc520_cdp/sc520_cdp.c

@@ -114,7 +114,7 @@ static void irq_init(void)
 
 }
 
-
+#ifdef CONFIG_PCI
 /* PCI stuff */
 static void pci_sc520_cdp_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
 {
@@ -129,7 +129,7 @@ static void pci_sc520_cdp_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
 	};
 	static int next_irq_index=0;
 
-	char tmp_pin;
+	uchar tmp_pin;
 	int pin;
 
 	pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &tmp_pin);
@@ -193,7 +193,7 @@ void pci_init_board(void)
 {
 	pci_sc520_init(&sc520_cdp_hose);
 }
-
+#endif
 
 static void silence_uart(int port)
 {
@@ -563,12 +563,12 @@ void spi_eeprom_probe(int x)
 {
 }
 
-int spi_eeprom_read(int x, int offset, char *buffer, int len)
+int spi_eeprom_read(int x, int offset, uchar *buffer, int len)
 {
        return 0;
 }
 
-int spi_eeprom_write(int x, int offset, char *buffer, int len)
+int spi_eeprom_write(int x, int offset, uchar *buffer, int len)
 {
        return 0;
 }

board/stxxtc/stxxtc.c

@@ -599,20 +599,6 @@ void hw_watchdog_reset(void)
 
 #endif
 
-#ifdef CONFIG_SHOW_ACTIVITY
-
-/* called from timer interrupt every 1/CFG_HZ sec */
-void board_show_activity(ulong timestamp)
-{
-}
-
-/* called when looping */
-void show_activity(int arg)
-{
-}
-
-#endif
-
 #if defined(CFG_CONSOLE_IS_IN_ENV) && defined(CFG_CONSOLE_OVERWRITE_ROUTINE)
 int overwrite_console(void)
 {

board/svm_sc8xx/svm_sc8xx.c

@@ -154,7 +154,6 @@ phys_size_t initdram (int board_type)
 }
 
 #if defined(CONFIG_CMD_DOC)
-extern void doc_probe (ulong physadr);
 void doc_init (void)
 {
 	        doc_probe (CFG_DOC_BASE);

board/trab/tsc2000.c

@@ -27,6 +27,7 @@
 
 #include <common.h>
 #include <s3c2400.h>
+#include <div64.h>
 #include "tsc2000.h"
 
 #include "Pt1000_temp_data.h"
@@ -332,6 +333,7 @@ void tsc2000_reg_init (void)
 int tsc2000_interpolate(long value, long data[][2], long *result)
 {
 	int i;
+	unsigned long long val;
 
 	/* the data is sorted and the first element is upper
 	 * limit so we can easily check for out-of-band values
@@ -347,10 +349,10 @@ int tsc2000_interpolate(long value, long data[][2], long *result)
 	   result in 'long long'.
 	*/
 
-	*result = data[i-1][1] +
+	val = ((unsigned long long)(data[i][1] - data[i-1][1])
-		((unsigned long long)(data[i][1] - data[i-1][1])
+		   * (unsigned long long)(value - data[i-1][0]));
-		 * (unsigned long long)(value - data[i-1][0]))
+	do_div(val, (data[i][0] - data[i-1][0]));
-		/ (data[i][0] - data[i-1][0]);
+	*result = data[i-1][1] + val;
 
 	return 0;
 }

board/xilinx/ml507/Makefile

@@ -1,6 +1,7 @@
 #
-# (C) Copyright 2000-2006
+# (C) Copyright 2008
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+# Ricardo Ribalda,Universidad Autonoma de Madrid, ricardo.ribalda@uam.es
+# This work has been supported by: Qtechnology http://qtec.com/
 #
 # See file CREDITS for list of people who contributed to this
 # project.
@@ -21,38 +22,6 @@
 # MA 02111-1307 USA
 #
 
-include $(TOPDIR)/config.mk
+COBJS	+= $(BOARD).o
-ifneq ($(OBJTREE),$(SRCTREE))
-endif
 
-INCS		:=
+include $(SRCTREE)/board/xilinx/ppc440-generic/Makefile
-CFLAGS		+= $(INCS)
-HOST_CFLAGS	+= $(INCS)
-
-LIB	= $(obj)lib$(BOARD).a
-
-COBJS	= $(BOARD).o
-
-SOBJS	= init.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $^
-
-clean:
-	rm -f $(SOBJS) $(OBJS)
-
-distclean:	clean
-	rm -f $(LIB) core *.bak .depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################

board/xilinx/ml507/config.mk

@@ -1,6 +1,7 @@
 #
-# (C) Copyright 2000
+# (C) Copyright 2008
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+# Ricardo Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+# Work supported by Qtechnology http://www.qtec.com
 #
 # See file CREDITS for list of people who contributed to this
 # project.
@@ -20,8 +21,6 @@
 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 # MA 02111-1307 USA
 #
-sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+#
 
-ifndef TEXT_BASE
+sinclude $(SRCTREE)/board/xilinx/ppc440-generic/config.mk
-TEXT_BASE = 0x04000000
-endif

board/xilinx/ml507/init.S

@@ -1,53 +0,0 @@
-/*
- *  (C) Copyright 2008
- *  Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
- *  This work has been supported by: QTechnology  http://qtec.com/
- *
- *  This program is free software: you can redistribute it and/or modify
- *  it under the terms of the GNU General Public License as published by
- *  the Free Software Foundation, either version 2 of the License, or
- *  (at your option) any later version.
- *
- *  This program is distributed in the hope that it will be useful,
- *  but WITHOUT ANY WARRANTY; without even the implied warranty of
- *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *  GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#include <ppc_asm.tmpl>
-#include <config.h>
-#include <asm-ppc/mmu.h>
-
-.section .bootpg,"ax"
-.globl tlbtab
-
-tlbtab:
-tlbtab_start
-	/* SDRAM */
-tlbentry(XPAR_DDR2_SDRAM_MEM_BASEADDR, SZ_256M, CFG_SDRAM_BASE, 0,
-	 AC_R | AC_W | AC_X | SA_G | SA_I)
-	/* UART */
-tlbentry(XPAR_UARTLITE_0_BASEADDR, SZ_64K, XPAR_UARTLITE_0_BASEADDR, 0,
-	 AC_R | AC_W | SA_G | SA_I)
-	/* PIC */
-tlbentry(XPAR_INTC_0_BASEADDR, SZ_64K, XPAR_INTC_0_BASEADDR, 0,
-	 AC_R | AC_W | SA_G | SA_I)
-#ifdef XPAR_IIC_EEPROM_BASEADDR
-	/* I2C */
-tlbentry(XPAR_IIC_EEPROM_BASEADDR, SZ_64K, XPAR_IIC_EEPROM_BASEADDR, 0,
-	 AC_R | AC_W | SA_G | SA_I)
-#endif
-#ifdef XPAR_LLTEMAC_0_BASEADDR
-	/* Net */
-tlbentry(XPAR_LLTEMAC_0_BASEADDR, SZ_64K, XPAR_LLTEMAC_0_BASEADDR, 0,
-	 AC_R | AC_W | SA_G | SA_I)
-#endif
-#ifdef XPAR_FLASH_MEM0_BASEADDR
-	/*Flash*/
-tlbentry(XPAR_FLASH_MEM0_BASEADDR, SZ_256M, XPAR_FLASH_MEM0_BASEADDR, 0,
-	 AC_R | AC_W | AC_X | SA_G | SA_I)
-#endif
-tlbtab_end

board/xilinx/ml507/ml507.c

@@ -20,28 +20,9 @@
 #include <common.h>
 #include <asm/processor.h>
 
-int board_pre_init(void)
-{
-	return 0;
-}
 
 int checkboard(void)
 {
-	puts("ML507 Board\n");
+	puts("Xilinx ML507 Board\n");
 	return 0;
 }
-
-phys_size_t initdram(int board_type)
-{
-	return get_ram_size(XPAR_DDR2_SDRAM_MEM_BASEADDR,
-			    CFG_SDRAM_SIZE_MB * 1024 * 1024);
-}
-
-void get_sys_info(sys_info_t * sysInfo)
-{
-	sysInfo->freqProcessor = XPAR_CORE_CLOCK_FREQ_HZ;
-	sysInfo->freqPLB = XPAR_PLB_CLOCK_FREQ_HZ;
-	sysInfo->freqPCI = 0;
-
-	return;
-}

board/xilinx/ml507/xparameters.h

@@ -24,7 +24,6 @@
 #define XPAR_DDR2_SDRAM_MEM_BASEADDR	0x00000000
 #define XPAR_IIC_EEPROM_BASEADDR	0x81600000
 #define XPAR_INTC_0_BASEADDR		0x81800000
-#define XPAR_LLTEMAC_0_BASEADDR 	0x81C00000
 #define XPAR_UARTLITE_0_BASEADDR	0x84000000
 #define XPAR_FLASH_MEM0_BASEADDR	0xFE000000
 #define XPAR_PLB_CLOCK_FREQ_HZ		100000000

board/xilinx/ppc440-generic/Makefile

@@ -0,0 +1,62 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2008
+# Ricardo Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+# Work supported by Qtechnology http://www.qtec.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+endif
+
+INCS		:=
+CFLAGS		+= $(INCS)
+HOST_CFLAGS	+= $(INCS)
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	+= ../../xilinx/ppc440-generic/xilinx_ppc440_generic.o
+
+SOBJS	+= ../../xilinx/ppc440-generic/init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/xilinx/ppc440-generic/config.mk

@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2008
+# Ricardo Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+# Work supported by Qtechnology http://www.qtec.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+sinclude $(obj)/board/$(BOARDDIR)/config.tmp

board/xilinx/ppc440-generic/init.S

@@ -0,0 +1,45 @@
+/*
+ *  (C) Copyright 2008
+ *  Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+ *  This work has been supported by: QTechnology  http://qtec.com/
+ *
+ *  This program is free software: you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation, either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <ppc_asm.tmpl>
+#include <config.h>
+#include <asm-ppc/mmu.h>
+
+.section .bootpg,"ax"
+.globl tlbtab
+
+tlbtab:
+tlbtab_start
+tlbentry(0x00000000, SZ_256M, 0x00000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0x10000000, SZ_256M, 0x10000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0x20000000, SZ_256M, 0x20000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0x30000000, SZ_256M, 0x30000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0x40000000, SZ_256M, 0x40000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0x50000000, SZ_256M, 0x50000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0x60000000, SZ_256M, 0x60000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0x70000000, SZ_256M, 0x70000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0x80000000, SZ_256M, 0x80000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0x90000000, SZ_256M, 0x90000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0xa0000000, SZ_256M, 0xa0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0xb0000000, SZ_256M, 0xb0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0xc0000000, SZ_256M, 0xc0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0xd0000000, SZ_256M, 0xd0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0xe0000000, SZ_256M, 0xe0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbentry(0xf0000000, SZ_256M, 0xf0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I)
+tlbtab_end

board/xilinx/ppc440-generic/xilinx_ppc440_generic.c

@@ -0,0 +1,52 @@
+/*
+ * (C) Copyright 2008
+ * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+ * This work has been supported by: QTechnology  http://qtec.com/
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <config.h>
+#include <common.h>
+#include <asm/processor.h>
+
+int __board_pre_init(void)
+{
+	return 0;
+}
+int board_pre_init(void) __attribute__((weak, alias("__board_pre_init")));
+
+int __checkboard(void)
+{
+	puts("Xilinx PPC440 Generic Board\n");
+	return 0;
+}
+int checkboard(void) __attribute__((weak, alias("__checkboard")));
+
+phys_size_t __initdram(int board_type)
+{
+	return get_ram_size(XPAR_DDR2_SDRAM_MEM_BASEADDR,
+			    CFG_SDRAM_SIZE_MB * 1024 * 1024);
+}
+phys_size_t initdram(int) __attribute__((weak, alias("__initdram")));
+
+void __get_sys_info(sys_info_t *sysInfo)
+{
+	sysInfo->freqProcessor = XPAR_CORE_CLOCK_FREQ_HZ;
+	sysInfo->freqPLB = XPAR_PLB_CLOCK_FREQ_HZ;
+	sysInfo->freqPCI = 0;
+
+	return;
+}
+void get_sys_info(sys_info_t *) __attribute__((weak, alias("__get_sys_info")));

board/xilinx/ppc440-generic/xparameters.h

@@ -0,0 +1,34 @@
+/*
+ * (C) Copyright 2008
+ * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+ * This work has been supported by: QTechnology  http://qtec.com/
+ * based on xparameters-ml507.h by Xilinx
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef XPARAMETER_H
+#define XPARAMETER_H
+
+#define XPAR_DDR2_SDRAM_MEM_BASEADDR	0x00000000
+#define XPAR_IIC_EEPROM_BASEADDR	0x81600000
+#define XPAR_INTC_0_BASEADDR		0x81800000
+#define XPAR_UARTLITE_0_BASEADDR	0x84000000
+#define XPAR_FLASH_MEM0_BASEADDR	0xFE000000
+#define XPAR_PLB_CLOCK_FREQ_HZ		100000000
+#define XPAR_CORE_CLOCK_FREQ_HZ		400000000
+#define XPAR_INTC_MAX_NUM_INTR_INPUTS	13
+#define XPAR_UARTLITE_0_BAUDRATE	9600
+
+#endif

common/Makefile

@@ -56,7 +56,8 @@ COBJS-y += env_nowhere.o
 
 # command
 COBJS-$(CONFIG_CMD_AMBAPP) += cmd_ambapp.o
-COBJS-$(CONFIG_AUTOSCRIPT)$(CONFIG_CMD_AUTOSCRIPT) += cmd_autoscript.o
+COBJS-$(CONFIG_AUTOSCRIPT) += cmd_autoscript.o
+COBJS-$(CONFIG_CMD_AUTOSCRIPT) += cmd_autoscript.o
 COBJS-$(CONFIG_CMD_BDI) += cmd_bdinfo.o
 COBJS-$(CONFIG_CMD_BEDBUG) += bedbug.o cmd_bedbug.o
 COBJS-$(CONFIG_CMD_BMP) += cmd_bmp.o
@@ -110,7 +111,8 @@ COBJS-$(CONFIG_LOGBUFFER) += cmd_log.o
 COBJS-y += cmd_mac.o
 COBJS-y += cmd_mem.o
 COBJS-$(CONFIG_CMD_MFSL) += cmd_mfsl.o
-COBJS-$(CONFIG_MII)$(CONFIG_CMD_MII) += miiphyutil.o
+COBJS-$(CONFIG_MII) += miiphyutil.o
+COBJS-$(CONFIG_CMD_MII) += miiphyutil.o
 COBJS-$(CONFIG_CMD_MII) += cmd_mii.o
 COBJS-$(CONFIG_CMD_MISC) += cmd_misc.o
 COBJS-$(CONFIG_CMD_MMC) += cmd_mmc.o
@@ -151,8 +153,7 @@ COBJS-$(CONFIG_LYNXKDI) += lynxkdi.o
 COBJS-$(CONFIG_USB_KEYBOARD) += usb_kbd.o
 COBJS-$(CONFIG_DDR_SPD) += ddr_spd.o
 
-COBJS-y	+= $(COBJS-yy)
+COBJS	:= $(sort $(COBJS-y))
-COBJS	:= $(COBJS-y)
 SRCS	:= $(AOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(AOBJS) $(COBJS))
 

common/cmd_bootm.c

@@ -108,8 +108,8 @@ static boot_os_fn do_bootm_qnxelf;
 int do_bootvx (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
 int do_bootelf (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
 #endif
-#if defined(CONFIG_ARTOS) && defined(CONFIG_PPC)
+#if defined(CONFIG_INTEGRITY)
-static boot_os_fn do_bootm_artos;
+static boot_os_fn do_bootm_integrity;
 #endif
 
 ulong load_addr = CFG_LOAD_ADDR;	/* Default Load Address */
@@ -337,13 +337,13 @@ static int bootm_load_os(image_info_t os, ulong *load_end, int boot_progress)
 		return BOOTM_ERR_UNIMPLEMENTED;
 	}
 	puts ("OK\n");
-	debug ("   kernel loaded at 0x%08lx, end = 0x%08lx\n", load, load_end);
+	debug ("   kernel loaded at 0x%08lx, end = 0x%8p\n", load, load_end);
 	if (boot_progress)
 		show_boot_progress (7);
 
 	if ((load < blob_end) && (*load_end > blob_start)) {
 		debug ("images.os.start = 0x%lX, images.os.end = 0x%lx\n", blob_start, blob_end);
-		debug ("images.os.load = 0x%lx, load_end = 0x%lx\n", load, load_end);
+		debug ("images.os.load = 0x%lx, load_end = 0x%p\n", load, load_end);
 
 		return BOOTM_ERR_OVERLAP;
 	}
@@ -455,9 +455,9 @@ int do_bootm (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	    break;
 #endif
 
-#ifdef CONFIG_ARTOS
+#ifdef CONFIG_INTEGRITY
-	case IH_OS_ARTOS:
+	case IH_OS_INTEGRITY:
-	    do_bootm_artos (0, argc, argv, &images);
+	    do_bootm_integrity (0, argc, argv, &images);
 	    break;
 #endif
 	}
@@ -854,6 +854,12 @@ static int image_info (ulong addr)
 		}
 
 		fit_print_contents (hdr);
+
+		if (!fit_all_image_check_hashes (hdr)) {
+			puts ("Bad hash in FIT image!\n");
+			return 1;
+		}
+
 		return 0;
 #endif
 	default:
@@ -1153,92 +1159,31 @@ static int do_bootm_qnxelf(int flag, int argc, char *argv[],
 }
 #endif
 
-#if defined(CONFIG_ARTOS) && defined(CONFIG_PPC)
+#ifdef CONFIG_INTEGRITY
-static int do_bootm_artos (int flag, int argc, char *argv[],
+static int do_bootm_integrity (int flag, int argc, char *argv[],
 			   bootm_headers_t *images)
 {
-	ulong top;
+	void (*entry_point)(void);
-	char *s, *cmdline;
-	char **fwenv, **ss;
-	int i, j, nxt, len, envno, envsz;
-	bd_t *kbd;
-	void (*entry)(bd_t *bd, char *cmdline, char **fwenv, ulong top);
 
 #if defined(CONFIG_FIT)
 	if (!images->legacy_hdr_valid) {
-		fit_unsupported_reset ("ARTOS");
+		fit_unsupported_reset ("INTEGRITY");
 		return 1;
 	}
 #endif
 
+	entry_point = (void (*)(void))images->ep;
+
+	printf ("## Transferring control to INTEGRITY (at address %08lx) ...\n",
+		(ulong)entry_point);
+
+	show_boot_progress (15);
+
 	/*
-	 * Booting an ARTOS kernel image + application
+	 * INTEGRITY Parameters:
+	 *   None
 	 */
-
+	(*entry_point)();
-	/* this used to be the top of memory, but was wrong... */
-#ifdef CONFIG_PPC
-	/* get stack pointer */
-	asm volatile ("mr %0,1" : "=r"(top) );
-#endif
-	debug ("## Current stack ends at 0x%08lX ", top);
-
-	top -= 2048;		/* just to be sure */
-	if (top > CFG_BOOTMAPSZ)
-		top = CFG_BOOTMAPSZ;
-	top &= ~0xF;
-
-	debug ("=> set upper limit to 0x%08lX\n", top);
-
-	/* first check the artos specific boot args, then the linux args*/
-	if ((s = getenv( "abootargs")) == NULL && (s = getenv ("bootargs")) == NULL)
-		s = "";
-
-	/* get length of cmdline, and place it */
-	len = strlen (s);
-	top = (top - (len + 1)) & ~0xF;
-	cmdline = (char *)top;
-	debug ("## cmdline at 0x%08lX ", top);
-	strcpy (cmdline, s);
-
-	/* copy bdinfo */
-	top = (top - sizeof (bd_t)) & ~0xF;
-	debug ("## bd at 0x%08lX ", top);
-	kbd = (bd_t *)top;
-	memcpy (kbd, gd->bd, sizeof (bd_t));
-
-	/* first find number of env entries, and their size */
-	envno = 0;
-	envsz = 0;
-	for (i = 0; env_get_char (i) != '\0'; i = nxt + 1) {
-		for (nxt = i; env_get_char (nxt) != '\0'; ++nxt)
-			;
-		envno++;
-		envsz += (nxt - i) + 1;	/* plus trailing zero */
-	}
-	envno++;	/* plus the terminating zero */
-	debug ("## %u envvars total size %u ", envno, envsz);
-
-	top = (top - sizeof (char **) * envno) & ~0xF;
-	fwenv = (char **)top;
-	debug ("## fwenv at 0x%08lX ", top);
-
-	top = (top - envsz) & ~0xF;
-	s = (char *)top;
-	ss = fwenv;
-
-	/* now copy them */
-	for (i = 0; env_get_char (i) != '\0'; i = nxt + 1) {
-		for (nxt = i; env_get_char (nxt) != '\0'; ++nxt)
-			;
-		*ss++ = s;
-		for (j = i; j < nxt; ++j)
-			*s++ = env_get_char (j);
-		*s++ = '\0';
-	}
-	*ss++ = NULL;	/* terminate */
-
-	entry = (void (*)(bd_t *, char *, char **, ulong))images->ep;
-	(*entry) (kbd, cmdline, fwenv, top);
 
 	return 1;
 }

common/image.c

@@ -105,9 +105,6 @@ static table_entry_t uimage_arch[] = {
 
 static table_entry_t uimage_os[] = {
 	{	IH_OS_INVALID,	NULL,		"Invalid OS",		},
-#if defined(CONFIG_ARTOS) || defined(USE_HOSTCC)
-	{	IH_OS_ARTOS,	"artos",	"ARTOS",		},
-#endif
 	{	IH_OS_LINUX,	"linux",	"Linux",		},
 #if defined(CONFIG_LYNXKDI) || defined(USE_HOSTCC)
 	{	IH_OS_LYNXOS,	"lynxos",	"LynxOS",		},
@@ -119,6 +116,9 @@ static table_entry_t uimage_os[] = {
 	{	IH_OS_QNX,	"qnx",		"QNX",			},
 	{	IH_OS_VXWORKS,	"vxworks",	"VxWorks",		},
 #endif
+#if defined(CONFIG_INTEGRITY) || defined(USE_HOSTCC)
+	{	IH_OS_INTEGRITY,"integrity",	"INTEGRITY",		},
+#endif
 #ifdef USE_HOSTCC
 	{	IH_OS_4_4BSD,	"4_4bsd",	"4_4BSD",		},
 	{	IH_OS_DELL,	"dell",		"Dell",			},
@@ -2645,27 +2645,29 @@ int fit_image_check_hashes (const void *fit, int image_noffset)
 				continue;
 
 			if (fit_image_hash_get_algo (fit, noffset, &algo)) {
-				err_msg = "Can't get hash algo property";
+				err_msg = " error!\nCan't get hash algo "
+						"property";
 				goto error;
 			}
 			printf ("%s", algo);
 
 			if (fit_image_hash_get_value (fit, noffset, &fit_value,
 							&fit_value_len)) {
-				err_msg = "Can't get hash value property";
+				err_msg = " error!\nCan't get hash value "
+						"property";
 				goto error;
 			}
 
 			if (calculate_hash (data, size, algo, value, &value_len)) {
-				err_msg = "Unsupported hash algorithm";
+				err_msg = " error!\nUnsupported hash algorithm";
 				goto error;
 			}
 
 			if (value_len != fit_value_len) {
-				err_msg = "Bad hash value len";
+				err_msg = " error !\nBad hash value len";
 				goto error;
 			} else if (memcmp (value, fit_value, value_len) != 0) {
-				err_msg = "Bad hash value";
+				err_msg = " error!\nBad hash value";
 				goto error;
 			}
 			printf ("+ ");
@@ -2681,6 +2683,55 @@ error:
 	return 0;
 }
 
+/**
+ * fit_all_image_check_hashes - verify data intergity for all images
+ * @fit: pointer to the FIT format image header
+ *
+ * fit_all_image_check_hashes() goes over all images in the FIT and
+ * for every images checks if all it's hashes are valid.
+ *
+ * returns:
+ *     1, if all hashes of all images are valid
+ *     0, otherwise (or on error)
+ */
+int fit_all_image_check_hashes (const void *fit)
+{
+	int images_noffset;
+	int noffset;
+	int ndepth;
+	int count;
+
+	/* Find images parent node offset */
+	images_noffset = fdt_path_offset (fit, FIT_IMAGES_PATH);
+	if (images_noffset < 0) {
+		printf ("Can't find images parent node '%s' (%s)\n",
+			FIT_IMAGES_PATH, fdt_strerror (images_noffset));
+		return 0;
+	}
+
+	/* Process all image subnodes, check hashes for each */
+	printf ("## Checking hash(es) for FIT Image at %08lx ...\n",
+		(ulong)fit);
+	for (ndepth = 0, count = 0,
+		noffset = fdt_next_node (fit, images_noffset, &ndepth);
+		(noffset >= 0) && (ndepth > 0);
+		noffset = fdt_next_node (fit, noffset, &ndepth)) {
+		if (ndepth == 1) {
+			/*
+			 * Direct child node of the images parent node,
+			 * i.e. component image node.
+			 */
+			printf ("   Hash(es) for Image %u (%s): ", count++,
+					fit_get_name (fit, noffset, NULL));
+
+			if (!fit_image_check_hashes (fit, noffset))
+				return 0;
+			printf ("\n");
+		}
+	}
+	return 1;
+}
+
 /**
  * fit_image_check_os - check whether image node is of a given os type
  * @fit: pointer to the FIT format image header

common/usb.c

@@ -126,10 +126,15 @@ int usb_init(void)
  */
 int usb_stop(void)
 {
-	asynch_allowed=1;
+	int res = 0;
+
+	if (usb_started) {
+		asynch_allowed = 1;
 		usb_started = 0;
 		usb_hub_reset();
-	return usb_lowlevel_stop();
+		res = usb_lowlevel_stop();
+	}
+	return res;
 }
 
 /*

common/usb_kbd.c

@@ -162,6 +162,8 @@ int drv_usb_kbd_init(void)
 	/* scan all USB Devices */
 	for(i=0;i<USB_MAX_DEVICE;i++) {
 		dev=usb_get_dev_index(i); /* get device */
+		if(dev == NULL)
+			return -1;
 		if(dev->devnum!=-1) {
 			if(usb_kbd_probe(dev,0)==1) { /* Ok, we found a keyboard */
 				/* check, if it is already registered */

cpu/arm1176/s3c64xx/interrupts.c

@@ -41,6 +41,7 @@
 #include <common.h>
 #include <asm/proc-armv/ptrace.h>
 #include <s3c6400.h>
+#include <div64.h>
 
 static ulong timer_load_val;
 
@@ -148,7 +149,9 @@ void reset_timer(void)
 
 ulong get_timer_masked(void)
 {
-	return get_ticks() / (timer_load_val / (100 * CFG_HZ));
+	unsigned long long res = get_ticks();
+	do_div (res, (timer_load_val / (100 * CFG_HZ)));
+	return res;
 }
 
 ulong get_timer(ulong base)

cpu/arm946es/config.mk

@@ -25,3 +25,10 @@ PLATFORM_RELFLAGS += -fno-strict-aliasing  -fno-common -ffixed-r8 \
 	 -msoft-float
 
 PLATFORM_CPPFLAGS +=  -march=armv4
+# =========================================================================
+#
+# Supply options according to compiler version
+#
+# =========================================================================
+PLATFORM_CPPFLAGS +=$(call cc-option,-mapcs-32,-mabi=apcs-gnu)
+PLATFORM_RELFLAGS +=$(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,))

cpu/arm_intcm/config.mk

@@ -25,3 +25,10 @@ PLATFORM_RELFLAGS += -fno-strict-aliasing  -fno-common -ffixed-r8 \
 	 -msoft-float
 
 PLATFORM_CPPFLAGS +=  -march=armv4
+# =========================================================================
+#
+# Supply options according to compiler version
+#
+# =========================================================================
+PLATFORM_CPPFLAGS +=$(call cc-option,-mapcs-32,-mabi=apcs-gnu)
+PLATFORM_RELFLAGS +=$(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,))

cpu/ppc4xx/44x_spd_ddr2.c

@@ -60,8 +60,6 @@
 		       "SDRAM_" #mnemonic, SDRAM_##mnemonic, data);	\
 	} while (0)
 
-static inline void ppc4xx_ibm_ddr2_register_dump(void);
-
 #if defined(CONFIG_SPD_EEPROM)
 
 /*-----------------------------------------------------------------------------+
@@ -260,6 +258,7 @@ static void program_ecc_addr(unsigned long start_address,
 			     unsigned long num_bytes,
 			     unsigned long tlb_word2_i_value);
 #endif
+#if !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
 static void program_DQS_calibration(unsigned long *dimm_populated,
 				unsigned char *iic0_dimm_addr,
 				unsigned long num_dimm_banks);
@@ -268,54 +267,10 @@ static void	test(void);
 #else
 static void	DQS_calibration_process(void);
 #endif
+#endif
 int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
 void dcbz_area(u32 start_address, u32 num_bytes);
 
-static u32 mfdcr_any(u32 dcr)
-{
-	u32 val;
-
-	switch (dcr) {
-	case SDRAM_R0BAS + 0:
-		val = mfdcr(SDRAM_R0BAS + 0);
-		break;
-	case SDRAM_R0BAS + 1:
-		val = mfdcr(SDRAM_R0BAS + 1);
-		break;
-	case SDRAM_R0BAS + 2:
-		val = mfdcr(SDRAM_R0BAS + 2);
-		break;
-	case SDRAM_R0BAS + 3:
-		val = mfdcr(SDRAM_R0BAS + 3);
-		break;
-	default:
-		printf("DCR %d not defined in case statement!!!\n", dcr);
-		val = 0; /* just to satisfy the compiler */
-	}
-
-	return val;
-}
-
-static void mtdcr_any(u32 dcr, u32 val)
-{
-	switch (dcr) {
-	case SDRAM_R0BAS + 0:
-		mtdcr(SDRAM_R0BAS + 0, val);
-		break;
-	case SDRAM_R0BAS + 1:
-		mtdcr(SDRAM_R0BAS + 1, val);
-		break;
-	case SDRAM_R0BAS + 2:
-		mtdcr(SDRAM_R0BAS + 2, val);
-		break;
-	case SDRAM_R0BAS + 3:
-		mtdcr(SDRAM_R0BAS + 3, val);
-		break;
-	default:
-		printf("DCR %d not defined in case statement!!!\n", dcr);
-	}
-}
-
 static unsigned char spd_read(uchar chip, uint addr)
 {
 	unsigned char data[2];
@@ -609,7 +564,11 @@ phys_size_t initdram(int board_type)
 	/*------------------------------------------------------------------
 	 * DQS calibration.
 	 *-----------------------------------------------------------------*/
+#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
+	DQS_autocalibration();
+#else
 	program_DQS_calibration(dimm_populated, iic0_dimm_addr, num_dimm_banks);
+#endif
 
 #ifdef CONFIG_DDR_ECC
 	/*------------------------------------------------------------------
@@ -2329,18 +2288,6 @@ static unsigned long is_ecc_enabled(void)
 	return ecc;
 }
 
-static void blank_string(int size)
-{
-	int i;
-
-	for (i=0; i<size; i++)
-		putc('\b');
-	for (i=0; i<size; i++)
-		putc(' ');
-	for (i=0; i<size; i++)
-		putc('\b');
-}
-
 #ifdef CONFIG_DDR_ECC
 /*-----------------------------------------------------------------------------+
  * program_ecc.
@@ -2468,6 +2415,7 @@ static void program_ecc_addr(unsigned long start_address,
 }
 #endif
 
+#if !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
 /*-----------------------------------------------------------------------------+
  * program_DQS_calibration.
  *-----------------------------------------------------------------------------*/
@@ -3001,7 +2949,8 @@ static void test(void)
 		(ppcMfdcr_sdram(SDRAM_MCOPT1) & ~SDRAM_MCOPT1_MCHK_MASK)
 		| ecc_temp);
 }
-#endif
+#endif /* !HARD_CODED_DQS */
+#endif /* !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) */
 
 #else /* CONFIG_SPD_EEPROM */
 
@@ -3104,9 +3053,12 @@ phys_size_t initdram(int board_type)
 	/* Set Delay Control Registers */
 
 	mtsdram(SDRAM_DLCR, CFG_SDRAM0_DLCR);
+
+#if !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
 	mtsdram(SDRAM_RDCC, CFG_SDRAM0_RDCC);
 	mtsdram(SDRAM_RQDC, CFG_SDRAM0_RQDC);
 	mtsdram(SDRAM_RFDC, CFG_SDRAM0_RFDC);
+#endif /* !CONFIG_PPC4xx_DDR_AUTOCALIBRATION */
 
 	/*
 	 * Enable Controller by SDRAM0_MCOPT2[DCEN] = 1:
@@ -3115,18 +3067,98 @@ phys_size_t initdram(int board_type)
 	mfsdram(SDRAM_MCOPT2, val);
 	mtsdram(SDRAM_MCOPT2, val | SDRAM_MCOPT2_DCEN_ENABLE);
 
+#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+	/*------------------------------------------------------------------
+	 | DQS calibration.
+	 +-----------------------------------------------------------------*/
+	DQS_autocalibration();
+#endif /* !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) */
+#endif /* CONFIG_PPC4xx_DDR_AUTOCALIBRATION */
+
 #if defined(CONFIG_DDR_ECC)
 	ecc_init(CFG_SDRAM_BASE, CFG_MBYTES_SDRAM << 20);
 #endif /* defined(CONFIG_DDR_ECC) */
 
 	ppc4xx_ibm_ddr2_register_dump();
+
+#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
+	/*
+	 * Clear potential errors resulting from auto-calibration.
+	 * If not done, then we could get an interrupt later on when
+	 * exceptions are enabled.
+	 */
+	set_mcsr(get_mcsr());
+#endif /* CONFIG_PPC4xx_DDR_AUTOCALIBRATION */
+
 #endif /* !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */
 
 	return (CFG_MBYTES_SDRAM << 20);
 }
 #endif /* CONFIG_SPD_EEPROM */
 
-static inline void ppc4xx_ibm_ddr2_register_dump(void)
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#if defined(CONFIG_440)
+u32 mfdcr_any(u32 dcr)
+{
+	u32 val;
+
+	switch (dcr) {
+	case SDRAM_R0BAS + 0:
+		val = mfdcr(SDRAM_R0BAS + 0);
+		break;
+	case SDRAM_R0BAS + 1:
+		val = mfdcr(SDRAM_R0BAS + 1);
+		break;
+	case SDRAM_R0BAS + 2:
+		val = mfdcr(SDRAM_R0BAS + 2);
+		break;
+	case SDRAM_R0BAS + 3:
+		val = mfdcr(SDRAM_R0BAS + 3);
+		break;
+	default:
+		printf("DCR %d not defined in case statement!!!\n", dcr);
+		val = 0; /* just to satisfy the compiler */
+	}
+
+	return val;
+}
+
+void mtdcr_any(u32 dcr, u32 val)
+{
+	switch (dcr) {
+	case SDRAM_R0BAS + 0:
+		mtdcr(SDRAM_R0BAS + 0, val);
+		break;
+	case SDRAM_R0BAS + 1:
+		mtdcr(SDRAM_R0BAS + 1, val);
+		break;
+	case SDRAM_R0BAS + 2:
+		mtdcr(SDRAM_R0BAS + 2, val);
+		break;
+	case SDRAM_R0BAS + 3:
+		mtdcr(SDRAM_R0BAS + 3, val);
+		break;
+	default:
+		printf("DCR %d not defined in case statement!!!\n", dcr);
+	}
+}
+#endif /* defined(CONFIG_440) */
+
+void blank_string(int size)
+{
+	int i;
+
+	for (i = 0; i < size; i++)
+		putc('\b');
+	for (i = 0; i < size; i++)
+		putc(' ');
+	for (i = 0; i < size; i++)
+		putc('\b');
+}
+#endif /* !defined(CONFIG_NAND_U_BOOT) &&  !defined(CONFIG_NAND_SPL) */
+
+inline void ppc4xx_ibm_ddr2_register_dump(void)
 {
 #if defined(DEBUG)
 	printf("\nPPC4xx IBM DDR2 Register Dump:\n");

cpu/ppc4xx/4xx_enet.c

@@ -198,6 +198,7 @@
 #define BI_PHYMODE_RMII  8
 #endif
 #endif
+#define BI_PHYMODE_SGMII 9
 
 #if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
     defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
@@ -216,6 +217,52 @@
 #define MAL_RX_CHAN_MUL	1
 #endif
 
+/*--------------------------------------------------------------------+
+ * Fixed PHY (PHY-less) support for Ethernet Ports.
+ *--------------------------------------------------------------------*/
+
+/*
+ * Some boards do not have a PHY for each ethernet port. These ports
+ * are known as Fixed PHY (or PHY-less) ports. For such ports, set
+ * the appropriate CONFIG_PHY_ADDR equal to CONFIG_FIXED_PHY and
+ * then define CFG_FIXED_PHY_PORTS to define what the speed and
+ * duplex should be for these ports in the board configuration
+ * file.
+ *
+ * For Example:
+ *     #define CONFIG_FIXED_PHY   0xFFFFFFFF
+ *
+ *     #define CONFIG_PHY_ADDR    CONFIG_FIXED_PHY
+ *     #define CONFIG_PHY1_ADDR   1
+ *     #define CONFIG_PHY2_ADDR   CONFIG_FIXED_PHY
+ *     #define CONFIG_PHY3_ADDR   3
+ *
+ *     #define CFG_FIXED_PHY_PORT(devnum,speed,duplex) \
+ *                     {devnum, speed, duplex},
+ *
+ *     #define CFG_FIXED_PHY_PORTS \
+ *                     CFG_FIXED_PHY_PORT(0,1000,FULL) \
+ *                     CFG_FIXED_PHY_PORT(2,100,HALF)
+ */
+
+#ifndef CONFIG_FIXED_PHY
+#define CONFIG_FIXED_PHY	0xFFFFFFFF /* Fixed PHY (PHY-less) */
+#endif
+
+#ifndef CFG_FIXED_PHY_PORTS
+#define CFG_FIXED_PHY_PORTS	/* default is an empty array */
+#endif
+
+struct fixed_phy_port {
+	unsigned int devnum;	/* ethernet port */
+	unsigned int speed;	/* specified speed 10,100 or 1000 */
+	unsigned int duplex;	/* specified duplex FULL or HALF */
+};
+
+static const struct fixed_phy_port fixed_phy_port[] = {
+	CFG_FIXED_PHY_PORTS	/* defined in board configuration file */
+};
+
 /*-----------------------------------------------------------------------------+
  * Global variables. TX and RX descriptors and buffers.
  *-----------------------------------------------------------------------------*/
@@ -611,8 +658,17 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
 
 #if defined(CONFIG_460EX)
 	mode = 9;
+	mfsdr(SDR0_ETH_CFG, eth_cfg);
+	if (((eth_cfg & SDR0_ETH_CFG_SGMII0_ENABLE) > 0) &&
+	    ((eth_cfg & SDR0_ETH_CFG_SGMII1_ENABLE) > 0))
+		mode = 11; /* config SGMII */
 #else
 	mode = 10;
+	mfsdr(SDR0_ETH_CFG, eth_cfg);
+	if (((eth_cfg & SDR0_ETH_CFG_SGMII0_ENABLE) > 0) &&
+	    ((eth_cfg & SDR0_ETH_CFG_SGMII1_ENABLE) > 0) &&
+	    ((eth_cfg & SDR0_ETH_CFG_SGMII2_ENABLE) > 0))
+		mode = 12; /* config SGMII */
 #endif
 
 	/* TODO:
@@ -635,6 +691,8 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
 	/*
 	 * Right now only 2*RGMII is supported. Please extend when needed.
 	 * sr - 2008-02-19
+	 * Add SGMII support.
+	 * vg - 2008-07-28
 	 */
 	switch (mode) {
 	case 1:
@@ -761,6 +819,20 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
 		bis->bi_phymode[2] = BI_PHYMODE_RGMII;
 		bis->bi_phymode[3] = BI_PHYMODE_RGMII;
 		break;
+	case 11:
+		/* 2 SGMII - 460EX */
+		bis->bi_phymode[0] = BI_PHYMODE_SGMII;
+		bis->bi_phymode[1] = BI_PHYMODE_SGMII;
+		bis->bi_phymode[2] = BI_PHYMODE_NONE;
+		bis->bi_phymode[3] = BI_PHYMODE_NONE;
+		break;
+	case 12:
+		/* 3 SGMII - 460GT */
+		bis->bi_phymode[0] = BI_PHYMODE_SGMII;
+		bis->bi_phymode[1] = BI_PHYMODE_SGMII;
+		bis->bi_phymode[2] = BI_PHYMODE_SGMII;
+		bis->bi_phymode[3] = BI_PHYMODE_NONE;
+		break;
 	default:
 		break;
 	}
@@ -945,9 +1017,50 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 	out_be32((void *)EMAC_M1 + hw_p->hw_addr, mode_reg);
 #endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */
 
+#if defined(CONFIG_GPCS_PHY_ADDR) || defined(CONFIG_GPCS_PHY1_ADDR) || \
+    defined(CONFIG_GPCS_PHY2_ADDR) || defined(CONFIG_GPCS_PHY3_ADDR)
+	if (bis->bi_phymode[devnum] == BI_PHYMODE_SGMII) {
+		/*
+		 * In SGMII mode, GPCS access is needed for
+		 * communication with the internal SGMII SerDes.
+		 */
+		switch (devnum) {
+#if defined(CONFIG_GPCS_PHY_ADDR)
+		case 0:
+			reg = CONFIG_GPCS_PHY_ADDR;
+			break;
+#endif
+#if defined(CONFIG_GPCS_PHY1_ADDR)
+		case 1:
+			reg = CONFIG_GPCS_PHY1_ADDR;
+			break;
+#endif
+#if defined(CONFIG_GPCS_PHY2_ADDR)
+		case 2:
+			reg = CONFIG_GPCS_PHY2_ADDR;
+			break;
+#endif
+#if defined(CONFIG_GPCS_PHY3_ADDR)
+		case 3:
+			reg = CONFIG_GPCS_PHY3_ADDR;
+			break;
+#endif
+		}
+
+		mode_reg = in_be32((void *)EMAC_M1 + hw_p->hw_addr);
+		mode_reg |= EMAC_M1_MF_1000GPCS | EMAC_M1_IPPA_SET(reg);
+		out_be32((void *)EMAC_M1 + hw_p->hw_addr, mode_reg);
+
+		/* Configure GPCS interface to recommended setting for SGMII */
+		miiphy_reset(dev->name, reg);
+		miiphy_write(dev->name, reg, 0x04, 0x8120); /* AsymPause, FDX */
+		miiphy_write(dev->name, reg, 0x07, 0x2801); /* msg_pg, toggle */
+		miiphy_write(dev->name, reg, 0x00, 0x0140); /* 1Gbps, FDX     */
+	}
+#endif /* defined(CONFIG_GPCS_PHY_ADDR) */
+
 	/* wait for PHY to complete auto negotiation */
 	reg_short = 0;
-#ifndef CONFIG_CS8952_PHY
 	switch (devnum) {
 	case 0:
 		reg = CONFIG_PHY_ADDR;
@@ -974,6 +1087,9 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 
 	bis->bi_phynum[devnum] = reg;
 
+	if (reg == CONFIG_FIXED_PHY)
+		goto get_speed;
+
 #if defined(CONFIG_PHY_RESET)
 	/*
 	 * Reset the phy, only if its the first time through
@@ -986,6 +1102,27 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 		miiphy_write (dev->name, reg, 0x09, 0x0e00);
 		miiphy_write (dev->name, reg, 0x04, 0x01e1);
 #endif
+#if defined(CONFIG_M88E1112_PHY)
+		if (bis->bi_phymode[devnum] == BI_PHYMODE_SGMII) {
+			/*
+			 * Marvell 88E1112 PHY needs to have the SGMII MAC
+			 * interace (page 2) properly configured to
+			 * communicate with the 460EX/GT GPCS interface.
+			 */
+
+			/* Set access to Page 2 */
+			miiphy_write(dev->name, reg, 0x16, 0x0002);
+
+			miiphy_write(dev->name, reg, 0x00, 0x0040); /* 1Gbps */
+			miiphy_read(dev->name, reg, 0x1a, &reg_short);
+			reg_short |= 0x8000; /* bypass Auto-Negotiation */
+			miiphy_write(dev->name, reg, 0x1a, reg_short);
+			miiphy_reset(dev->name, reg); /* reset MAC interface */
+
+			/* Reset access to Page 0 */
+			miiphy_write(dev->name, reg, 0x16, 0x0000);
+		}
+#endif /* defined(CONFIG_M88E1112_PHY) */
 		miiphy_reset (dev->name, reg);
 
 #if defined(CONFIG_440GX) || \
@@ -1022,7 +1159,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 			miiphy_write (dev->name, reg, 0x1f, 0x0000);
 			/* end Vitesse/Cicada errata */
 		}
-#endif
+#endif /* defined(CONFIG_CIS8201_PHY) */
 
 #if defined(CONFIG_ET1011C_PHY)
 		/*
@@ -1041,9 +1178,9 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 
 			miiphy_write(dev->name, reg, 0x1c, 0x74f0);
 		}
-#endif
+#endif /* defined(CONFIG_ET1011C_PHY) */
 
-#endif
+#endif /* defined(CONFIG_440GX) ... */
 		/* Start/Restart autonegotiation */
 		phy_setup_aneg (dev->name, reg);
 		udelay (1000);
@@ -1073,15 +1210,30 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 			}
 			udelay (1000);	/* 1 ms */
 			miiphy_read (dev->name, reg, PHY_BMSR, &reg_short);
-
 		}
 		puts (" done\n");
 		udelay (500000);	/* another 500 ms (results in faster booting) */
 	}
-#endif /* #ifndef CONFIG_CS8952_PHY */
 
-	speed = miiphy_speed (dev->name, reg);
+get_speed:
-	duplex = miiphy_duplex (dev->name, reg);
+	if (reg == CONFIG_FIXED_PHY) {
+		for (i = 0; i < ARRAY_SIZE(fixed_phy_port); i++) {
+			if (devnum == fixed_phy_port[i].devnum) {
+				speed = fixed_phy_port[i].speed;
+				duplex = fixed_phy_port[i].duplex;
+				break;
+			}
+		}
+
+		if (i == ARRAY_SIZE(fixed_phy_port)) {
+			printf("ERROR: PHY (%s) not configured correctly!\n",
+				dev->name);
+			return -1;
+		}
+	} else {
+		speed = miiphy_speed(dev->name, reg);
+		duplex = miiphy_duplex(dev->name, reg);
+	}
 
 	if (hw_p->print_speed) {
 		hw_p->print_speed = 0;

cpu/ppc4xx/Makefile

@@ -35,6 +35,9 @@ SOBJS	+= kgdb.o
 COBJS	:= 40x_spd_sdram.o
 COBJS	+= 44x_spd_ddr.o
 COBJS	+= 44x_spd_ddr2.o
+ifdef CONFIG_PPC4xx_DDR_AUTOCALIBRATION
+COBJS	+= 4xx_ibm_ddr2_autocalib.o
+endif
 COBJS	+= 4xx_pci.o
 COBJS	+= 4xx_pcie.o
 COBJS	+= bedbug_405.o

cpu/ppc4xx/miiphy.c

@@ -180,8 +180,10 @@ int phy_setup_aneg (char *devname, unsigned char addr)
  *
  * sr: Currently on 460EX only EMAC0 works with MDIO, so we always
  * return EMAC0 offset here
+ * vg: For 460EX/460GT if internal GPCS PHY address is specified
+ * return appropriate EMAC offset
  */
-unsigned int miiphy_getemac_offset (void)
+unsigned int miiphy_getemac_offset(u8 addr)
 {
 #if (defined(CONFIG_440) && \
     !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \
@@ -233,6 +235,35 @@ unsigned int miiphy_getemac_offset (void)
 		return 0x100;
 #endif
 
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+	u32 eoffset = 0;
+
+	switch (addr) {
+#if defined(CONFIG_HAS_ETH1) && defined(CONFIG_GPCS_PHY1_ADDR)
+	case CONFIG_GPCS_PHY1_ADDR:
+		if (addr == EMAC_M1_IPPA_GET(in_be32((void *)EMAC_M1 + 0x100)))
+			eoffset = 0x100;
+		break;
+#endif
+#if defined(CONFIG_HAS_ETH2) && defined(CONFIG_GPCS_PHY2_ADDR)
+	case CONFIG_GPCS_PHY2_ADDR:
+		if (addr == EMAC_M1_IPPA_GET(in_be32((void *)EMAC_M1 + 0x300)))
+			eoffset = 0x300;
+		break;
+#endif
+#if defined(CONFIG_HAS_ETH3) && defined(CONFIG_GPCS_PHY3_ADDR)
+	case CONFIG_GPCS_PHY3_ADDR:
+		if (addr == EMAC_M1_IPPA_GET(in_be32((void *)EMAC_M1 + 0x400)))
+			eoffset = 0x400;
+		break;
+#endif
+	default:
+		eoffset = 0;
+		break;
+	}
+	return eoffset;
+#endif
+
 	return 0;
 #endif
 }
@@ -262,7 +293,7 @@ static int emac_miiphy_command(u8 addr, u8 reg, int cmd, u16 value)
 	u32 emac_reg;
 	u32 sta_reg;
 
-	emac_reg = miiphy_getemac_offset();
+	emac_reg = miiphy_getemac_offset(addr);
 
 	/* wait for completion */
 	if (emac_miiphy_wait(emac_reg) != 0)
@@ -311,7 +342,7 @@ int emac4xx_miiphy_read (char *devname, unsigned char addr, unsigned char reg,
 	unsigned long sta_reg;
 	unsigned long emac_reg;
 
-	emac_reg = miiphy_getemac_offset ();
+	emac_reg = miiphy_getemac_offset(addr);
 
 	if (emac_miiphy_command(addr, reg, EMAC_STACR_READ, 0) != 0)
 		return -1;

disk/part.c

@@ -124,6 +124,12 @@ void dev_print (block_dev_desc_t *dev_desc)
 			dev_desc->revision,
 			dev_desc->product);
 		break;
+	case IF_TYPE_USB:
+		printf ("Vendor: %s Rev: %s Prod: %s\n",
+			dev_desc->vendor,
+			dev_desc->revision,
+			dev_desc->product);
+		break;
 	case IF_TYPE_UNKNOWN:
 	default:
 		puts ("not available\n");

doc/uImage.FIT/source_file_format.txt

@@ -169,7 +169,7 @@ the '/images' node should have the following layout:
   - os : OS name, mandatory for type="kernel", valid OS names are: "openbsd",
     "netbsd", "freebsd", "4_4bsd", "linux", "svr4", "esix", "solaris", "irix",
     "sco", "dell", "ncr", "lynxos", "vxworks", "psos", "qnx", "u_boot",
-    "rtems", "artos", "unity".
+    "rtems", "unity", "integrity".
   - arch : Architecture name, mandatory for types: "standalone", "kernel",
     "firmware", "ramdisk" and "fdt". Valid architecture names are: "alpha",
     "arm", "i386", "ia64", "mips", "mips64", "ppc", "s390", "sh", "sparc",

drivers/mtd/mw_eeprom.c

@@ -1,7 +1,7 @@
 /* Three-wire (MicroWire) serial eeprom driver (for 93C46 and compatibles) */
 
 #include <common.h>
-#include <ssi.h>
+#include <asm/ic/ssi.h>
 
 /*
  * Serial EEPROM opcodes, including start bit

drivers/rtc/Makefile

@@ -32,8 +32,8 @@ COBJS-y += date.o
 COBJS-$(CONFIG_RTC_DS12887) += ds12887.o
 COBJS-$(CONFIG_RTC_DS1302) += ds1302.o
 COBJS-$(CONFIG_RTC_DS1306) += ds1306.o
-COBJS-$(CONFIG_RTC_DS1307)$(CONFIG_RTC_DS1338) += ds1307.o
+COBJS-$(CONFIG_RTC_DS1307) += ds1307.o
-COBJS-y += $(COBJS-yy)
+COBJS-$(CONFIG_RTC_DS1338) += ds1307.o
 COBJS-$(CONFIG_RTC_DS1337) += ds1337.o
 COBJS-$(CONFIG_RTC_DS1374) += ds1374.o
 COBJS-$(CONFIG_RTC_DS1556) += ds1556.o
@@ -59,7 +59,7 @@ COBJS-$(CONFIG_RTC_RX8025) += rx8025.o
 COBJS-$(CONFIG_RTC_S3C24X0) += s3c24x0_rtc.o
 COBJS-$(CONFIG_RTC_X1205) += x1205.o
 
-COBJS	:= $(COBJS-y)
+COBJS	:= $(sort $(COBJS-y))
 SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
 

drivers/rtc/mk48t59.c

@@ -227,7 +227,7 @@ void rtc_reset (void)
 	rtc_write(RTC_CONTROLB, control_b);
 }
 
-int rtc_set_watchdog(short multi, short res)
+void rtc_set_watchdog(short multi, short res)
 {
 	uchar wd_value;
 

drivers/rtc/rs5c372.c

@@ -195,8 +195,7 @@ rtc_get (struct rtc_time *tmp)
 /*
  * Set the RTC
  */
-void
+int rtc_set (struct rtc_time *tmp)
-rtc_set (struct rtc_time *tmp)
 {
 	unsigned char buf[8], reg15;
 	int ret;

drivers/serial/Makefile

@@ -33,13 +33,13 @@ COBJS-$(CONFIG_DRIVER_S3C4510_UART) += s3c4510b_uart.o
 COBJS-$(CONFIG_S3C64XX) += s3c64xx.o
 COBJS-y += serial.o
 COBJS-$(CONFIG_MAX3100_SERIAL) += serial_max3100.o
-COBJS-y += serial_pl010.o
+COBJS-$(CONFIG_PL010_SERIAL) += serial_pl01x.o
-COBJS-y += serial_pl011.o
+COBJS-$(CONFIG_PL011_SERIAL) += serial_pl01x.o
 COBJS-$(CONFIG_XILINX_UARTLITE) += serial_xuartlite.o
 COBJS-$(CONFIG_SCIF_CONSOLE) += serial_sh.o
 COBJS-$(CONFIG_USB_TTY) += usbtty.o
 
-COBJS	:= $(COBJS-y)
+COBJS	:= $(sort $(COBJS-y))
 SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
 

drivers/serial/serial_pl011.c

@@ -1,161 +0,0 @@
-/*
- * (C) Copyright 2000
- * Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
- *
- * (C) Copyright 2004
- * ARM Ltd.
- * Philippe Robin, <philippe.robin@arm.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/* Simple U-Boot driver for the PrimeCell PL011 UARTs on the IntegratorCP */
-/* Should be fairly simple to make it work with the PL010 as well */
-
-#include <common.h>
-
-#ifdef CFG_PL011_SERIAL
-
-#include "serial_pl011.h"
-
-#define IO_WRITE(addr, val) (*(volatile unsigned int *)(addr) = (val))
-#define IO_READ(addr) (*(volatile unsigned int *)(addr))
-
-/*
- * IntegratorCP has two UARTs, use the first one, at 38400-8-N-1
- * Versatile PB has four UARTs.
- */
-
-#define CONSOLE_PORT CONFIG_CONS_INDEX
-#define baudRate CONFIG_BAUDRATE
-static volatile unsigned char *const port[] = CONFIG_PL01x_PORTS;
-#define NUM_PORTS (sizeof(port)/sizeof(port[0]))
-
-static void pl011_putc (int portnum, char c);
-static int pl011_getc (int portnum);
-static int pl011_tstc (int portnum);
-
-
-int serial_init (void)
-{
-	unsigned int temp;
-	unsigned int divider;
-	unsigned int remainder;
-	unsigned int fraction;
-
-	/*
-	 ** First, disable everything.
-	 */
-	IO_WRITE (port[CONSOLE_PORT] + UART_PL011_CR, 0x0);
-
-	/*
-	 ** Set baud rate
-	 **
-	 ** IBRD = UART_CLK / (16 * BAUD_RATE)
-	 ** FBRD = ROUND((64 * MOD(UART_CLK,(16 * BAUD_RATE))) / (16 * BAUD_RATE))
-	 */
-	temp = 16 * baudRate;
-	divider = CONFIG_PL011_CLOCK / temp;
-	remainder = CONFIG_PL011_CLOCK % temp;
-	temp = (8 * remainder) / baudRate;
-	fraction = (temp >> 1) + (temp & 1);
-
-	IO_WRITE (port[CONSOLE_PORT] + UART_PL011_IBRD, divider);
-	IO_WRITE (port[CONSOLE_PORT] + UART_PL011_FBRD, fraction);
-
-	/*
-	 ** Set the UART to be 8 bits, 1 stop bit, no parity, fifo enabled.
-	 */
-	IO_WRITE (port[CONSOLE_PORT] + UART_PL011_LCRH,
-		  (UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN));
-
-	/*
-	 ** Finally, enable the UART
-	 */
-	IO_WRITE (port[CONSOLE_PORT] + UART_PL011_CR,
-		  (UART_PL011_CR_UARTEN | UART_PL011_CR_TXE |
-		   UART_PL011_CR_RXE));
-
-	return 0;
-}
-
-void serial_putc (const char c)
-{
-	if (c == '\n')
-		pl011_putc (CONSOLE_PORT, '\r');
-
-	pl011_putc (CONSOLE_PORT, c);
-}
-
-void serial_puts (const char *s)
-{
-	while (*s) {
-		serial_putc (*s++);
-	}
-}
-
-int serial_getc (void)
-{
-	return pl011_getc (CONSOLE_PORT);
-}
-
-int serial_tstc (void)
-{
-	return pl011_tstc (CONSOLE_PORT);
-}
-
-void serial_setbrg (void)
-{
-}
-
-static void pl011_putc (int portnum, char c)
-{
-	/* Wait until there is space in the FIFO */
-	while (IO_READ (port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_TXFF);
-
-	/* Send the character */
-	IO_WRITE (port[portnum] + UART_PL01x_DR, c);
-}
-
-static int pl011_getc (int portnum)
-{
-	unsigned int data;
-
-	/* Wait until there is data in the FIFO */
-	while (IO_READ (port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_RXFE);
-
-	data = IO_READ (port[portnum] + UART_PL01x_DR);
-
-	/* Check for an error flag */
-	if (data & 0xFFFFFF00) {
-		/* Clear the error */
-		IO_WRITE (port[portnum] + UART_PL01x_ECR, 0xFFFFFFFF);
-		return -1;
-	}
-
-	return (int) data;
-}
-
-static int pl011_tstc (int portnum)
-{
-	return !(IO_READ (port[portnum] + UART_PL01x_FR) &
-		 UART_PL01x_FR_RXFE);
-}
-
-#endif

drivers/serial/serial_pl01x.c

@@ -25,30 +25,31 @@
  * MA 02111-1307 USA
  */
 
-/* Simple U-Boot driver for the PrimeCell PL011 UARTs on the IntegratorCP */
+/* Simple U-Boot driver for the PrimeCell PL010/PL011 UARTs */
-/* Should be fairly simple to make it work with the PL010 as well */
 
 #include <common.h>
 #include <watchdog.h>
 
-#ifdef CFG_PL010_SERIAL
+#include "serial_pl01x.h"
-
-#include "serial_pl011.h"
 
 #define IO_WRITE(addr, val) (*(volatile unsigned int *)(addr) = (val))
 #define IO_READ(addr) (*(volatile unsigned int *)(addr))
 
-/* Integrator AP has two UARTs, we use the first one, at 38400-8-N-1 */
+/*
+ * Integrator AP has two UARTs, we use the first one, at 38400-8-N-1
+ * Integrator CP has two UARTs, use the first one, at 38400-8-N-1
+ * Versatile PB has four UARTs.
+ */
 #define CONSOLE_PORT CONFIG_CONS_INDEX
 #define baudRate CONFIG_BAUDRATE
 static volatile unsigned char *const port[] = CONFIG_PL01x_PORTS;
 #define NUM_PORTS (sizeof(port)/sizeof(port[0]))
 
+static void pl01x_putc (int portnum, char c);
+static int pl01x_getc (int portnum);
+static int pl01x_tstc (int portnum);
 
-static void pl010_putc (int portnum, char c);
+#ifdef CONFIG_PL010_SERIAL
-static int pl010_getc (int portnum);
-static int pl010_tstc (int portnum);
-
 
 int serial_init (void)
 {
@@ -103,15 +104,64 @@ int serial_init (void)
 	 */
 	IO_WRITE (port[CONSOLE_PORT] + UART_PL010_CR, (UART_PL010_CR_UARTEN));
 
-	return (0);
+	return 0;
 }
 
+#endif /* CONFIG_PL010_SERIAL */
+
+#ifdef CONFIG_PL011_SERIAL
+
+int serial_init (void)
+{
+	unsigned int temp;
+	unsigned int divider;
+	unsigned int remainder;
+	unsigned int fraction;
+
+	/*
+	 ** First, disable everything.
+	 */
+	IO_WRITE (port[CONSOLE_PORT] + UART_PL011_CR, 0x0);
+
+	/*
+	 ** Set baud rate
+	 **
+	 ** IBRD = UART_CLK / (16 * BAUD_RATE)
+	 ** FBRD = ROUND((64 * MOD(UART_CLK,(16 * BAUD_RATE))) / (16 * BAUD_RATE))
+	 */
+	temp = 16 * baudRate;
+	divider = CONFIG_PL011_CLOCK / temp;
+	remainder = CONFIG_PL011_CLOCK % temp;
+	temp = (8 * remainder) / baudRate;
+	fraction = (temp >> 1) + (temp & 1);
+
+	IO_WRITE (port[CONSOLE_PORT] + UART_PL011_IBRD, divider);
+	IO_WRITE (port[CONSOLE_PORT] + UART_PL011_FBRD, fraction);
+
+	/*
+	 ** Set the UART to be 8 bits, 1 stop bit, no parity, fifo enabled.
+	 */
+	IO_WRITE (port[CONSOLE_PORT] + UART_PL011_LCRH,
+		  (UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN));
+
+	/*
+	 ** Finally, enable the UART
+	 */
+	IO_WRITE (port[CONSOLE_PORT] + UART_PL011_CR,
+		  (UART_PL011_CR_UARTEN | UART_PL011_CR_TXE |
+		   UART_PL011_CR_RXE));
+
+	return 0;
+}
+
+#endif /* CONFIG_PL011_SERIAL */
+
 void serial_putc (const char c)
 {
 	if (c == '\n')
-		pl010_putc (CONSOLE_PORT, '\r');
+		pl01x_putc (CONSOLE_PORT, '\r');
 
-	pl010_putc (CONSOLE_PORT, c);
+	pl01x_putc (CONSOLE_PORT, c);
 }
 
 void serial_puts (const char *s)
@@ -123,19 +173,19 @@ void serial_puts (const char *s)
 
 int serial_getc (void)
 {
-	return pl010_getc (CONSOLE_PORT);
+	return pl01x_getc (CONSOLE_PORT);
 }
 
 int serial_tstc (void)
 {
-	return pl010_tstc (CONSOLE_PORT);
+	return pl01x_tstc (CONSOLE_PORT);
 }
 
 void serial_setbrg (void)
 {
 }
 
-static void pl010_putc (int portnum, char c)
+static void pl01x_putc (int portnum, char c)
 {
 	/* Wait until there is space in the FIFO */
 	while (IO_READ (port[portnum] + UART_PL01x_FR) & UART_PL01x_FR_TXFF)
@@ -145,7 +195,7 @@ static void pl010_putc (int portnum, char c)
 	IO_WRITE (port[portnum] + UART_PL01x_DR, c);
 }
 
-static int pl010_getc (int portnum)
+static int pl01x_getc (int portnum)
 {
 	unsigned int data;
 
@@ -165,11 +215,9 @@ static int pl010_getc (int portnum)
 	return (int) data;
 }
 
-static int pl010_tstc (int portnum)
+static int pl01x_tstc (int portnum)
 {
 	WATCHDOG_RESET();
 	return !(IO_READ (port[portnum] + UART_PL01x_FR) &
 		 UART_PL01x_FR_RXFE);
 }
-
-#endif

drivers/usb/usb_ohci.c

@@ -1943,7 +1943,9 @@ int usb_lowlevel_stop(void)
 	if(usb_cpu_stop())
 		return -1;
 #endif
-
+	/* This driver is no longer initialised. It needs a new low-level
+	 * init (board/cpu) before it can be used again. */
+	ohci_inited = 0;
 	return 0;
 }
 #endif /* CONFIG_USB_OHCI_NEW */

examples/82559_eeprom.c

@@ -51,13 +51,17 @@ static inline unsigned short swap16(unsigned short x)
 }
 
 
-static inline void *memcpy(void *dst, const void *src, unsigned int len)
+void * memcpy(void * dest,const void *src,size_t count)
 {
-	void * ret = dst;
+	char *tmp = (char *) dest, *s = (char *) src;
-	while (len-- > 0) *((char *)dst)++ = *((char *)src)++;
+
-	return ret;
+	while (count--)
+		*tmp++ = *s++;
+
+	return dest;
 }
 
+
 /* The EEPROM commands include the alway-set leading bit. */
 #define EE_WRITE_CMD	(5)
 #define EE_READ_CMD		(6)
@@ -156,7 +160,7 @@ static int reset_eeprom(unsigned long ioaddr, unsigned char *hwaddr)
 	int size_test;
 	int i;
 
-	printf("Resetting i82559 EEPROM @ 0x%08x ... ", ioaddr);
+	printf("Resetting i82559 EEPROM @ 0x%08lx ... ", ioaddr);
 
 	size_test = do_eeprom_cmd(ioaddr, (EE_READ_CMD << 8) << 16, 27);
 	eeprom_addr_size = (size_test & 0xffe0000) == 0xffe0000 ? 8 : 6;
@@ -305,7 +309,7 @@ write_config_word(int bus, int dev, int func, int reg, u16 data)
 int main (int argc, char *argv[])
 {
 	unsigned char *eth_addr;
-	char buf[6];
+	uchar buf[6];
 	int instance;
 
 	app_startup(argv);

include/asm-i386/byteorder.h

@@ -6,7 +6,7 @@
 #ifdef __GNUC__
 
 
-static __inline__ __const__ __u32 ___arch__swab32(__u32 x)
+static __inline__ __u32 ___arch__swab32(__u32 x)
 {
 #ifdef CONFIG_X86_BSWAP
 	__asm__("bswap %0" : "=r" (x) : "0" (x));
@@ -20,7 +20,7 @@ static __inline__ __const__ __u32 ___arch__swab32(__u32 x)
 	return x;
 }
 
-static __inline__ __const__ __u16 ___arch__swab16(__u16 x)
+static __inline__ __u16 ___arch__swab16(__u16 x)
 {
 	__asm__("xchgb %b0,%h0"		/* swap bytes		*/ \
 		: "=q" (x) \

include/asm-i386/global_data.h

@@ -59,8 +59,8 @@ typedef	struct {
 #define	GD_FLG_LOGINIT	0x00020		/* Log Buffer has been initialized	*/
 #define GD_FLG_DISABLE_CONSOLE	0x00040		/* Disable console (in & out)	 */
 
-extern gd_t *global_data;
+extern gd_t *gd;
 
-#define DECLARE_GLOBAL_DATA_PTR     gd_t *gd = global_data
+#define DECLARE_GLOBAL_DATA_PTR
 
 #endif /* __ASM_GBL_DATA_H */

include/asm-i386/ic/ssi.h

@@ -0,0 +1,34 @@
+/*
+ * (C) Copyright 2008
+ * Graeme Russ <graeme.russ@gmail.com>.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _ASM_IC_SSI_H_
+#define _ASM_IC_SSI_H_ 1
+
+int ssi_set_interface(int, int, int, int);
+void ssi_chip_select(int);
+u8 ssi_txrx_byte(u8);
+void ssi_tx_byte(u8);
+u8 ssi_rx_byte(void);
+
+
+#endif

include/asm-i386/pci.h

@@ -31,5 +31,4 @@ int pci_enable_legacy_video_ports(struct pci_controller* hose);
 int pci_shadow_rom(pci_dev_t dev, unsigned char *dest);
 void pci_remove_rom_window(struct pci_controller* hose, u32 addr);
 u32 pci_get_rom_window(struct pci_controller* hose, int size);
-
 #endif

include/asm-i386/string.h

@@ -5,6 +5,8 @@
  * We don't do inline string functions, since the
  * optimised inline asm versions are not small.
  */
+#undef __HAVE_ARCH_STRNCPY
+extern char *strncpy(char *__dest, __const__ char *__src, __kernel_size_t __n);
 
 #undef __HAVE_ARCH_STRRCHR
 extern char * strrchr(const char * s, int c);

include/asm-ppc/ppc4xx-sdram.h

@@ -29,6 +29,7 @@
 /*
  * SDRAM Controller
  */
+
 /*
  * XXX - ToDo: Revisit file to change all these lower case defines into
  * upper case. Also needs to be done in the controller setup code too
@@ -256,6 +257,7 @@
 #define SDRAM_DLYCAL_DLCV_ENCODE(x)	(((x)<<2) & SDRAM_DLYCAL_DLCV_MASK)
 #define SDRAM_DLYCAL_DLCV_DECODE(x)	(((x) & SDRAM_DLYCAL_DLCV_MASK)>>2)
 
+#if !defined(CONFIG_405EX)
 /*
  * Memory queue defines
  */
@@ -293,7 +295,6 @@
 
 #define SDRAM_PLBADDUHB		(SDRAMQ_DCR_BASE+0x10)  /* PLB base address upper 32 LL */
 
-#if !defined(CONFIG_405EX)
 /*
  * Memory Bank 0-7 configuration
  */
@@ -1401,4 +1402,18 @@
 
 #endif /* CONFIG_SDRAM_PPC4xx_DENALI_DDR2 */
 
+#ifndef __ASSEMBLY__
+/*
+ * Prototypes
+ */
+void inline blank_string(int size);
+inline void ppc4xx_ibm_ddr2_register_dump(void);
+u32 mfdcr_any(u32);
+void mtdcr_any(u32, u32);
+u32 ddr_wrdtr(u32);
+u32 ddr_clktr(u32);
+void spd_ddr_init_hang(void);
+u32 DQS_autocalibration(void);
+#endif /* __ASSEMBLY__ */
+
 #endif /* _PPC4xx_SDRAM_H_ */

include/common.h

@@ -236,6 +236,9 @@ int	autoscript (ulong addr, const char *fit_uname);
 
 extern ulong load_addr;		/* Default Load Address */
 
+/* common/cmd_doc.c */
+void	doc_probe(unsigned long physadr);
+
 /* common/cmd_nvedit.c */
 int	env_init     (void);
 void	env_relocate (void);

include/configs/CPCI4052.h

@@ -146,6 +146,8 @@
 
 #define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
+#define CONFIG_CMDLINE_EDITING		/* add command line history	*/
+
 #define CONFIG_LOOPW            1       /* enable loopw command         */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
@@ -219,6 +221,10 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
 /*-----------------------------------------------------------------------
  * FLASH organization
  */

include/configs/CPCI405AB.h

@@ -144,6 +144,8 @@
 
 #define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
+#define CONFIG_CMDLINE_EDITING		/* add command line history	*/
+
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
 #define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
@@ -215,6 +217,10 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
 /*-----------------------------------------------------------------------
  * FLASH organization
  */

include/configs/NETPHONE.h

@@ -487,8 +487,6 @@
 #define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
-#define CONFIG_ARTOS			/* include ARTOS support */
-
 #define CONFIG_LAST_STAGE_INIT		/* needed to reset the damn phys */
 
 /****************************************************************/

include/configs/NETTA.h

@@ -496,8 +496,6 @@
 #define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
-#define CONFIG_ARTOS			/* include ARTOS support */
-
 #define CONFIG_LAST_STAGE_INIT		/* needed to reset the damn phys */
 
 /***********************************************************************************************************

include/configs/NETTA2.h

@@ -488,8 +488,6 @@
 #define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
-#define CONFIG_ARTOS			/* include ARTOS support */
-
 #define CONFIG_LAST_STAGE_INIT		/* needed to reset the damn phys */
 
 /****************************************************************/
@@ -745,7 +743,6 @@ typedef unsigned int led_id_t;
 /* use board specific hardware */
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 #define CONFIG_HW_WATCHDOG
-#define CONFIG_SHOW_ACTIVITY
 
 /*************************************************************************************************/
 

include/configs/NETVIA.h

@@ -357,8 +357,6 @@
 /* Ethernet at SCC2 */
 #define CONFIG_SCC2_ENET
 
-#define CONFIG_ARTOS			/* include ARTOS support */
-
 /****************************************************************/
 
 #define DSP_SIZE	0x00010000	/* 64K */

include/configs/PIP405.h

@@ -281,7 +281,6 @@
  ***********************************************************/
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address			*/
-#define CONFIG_CS8952_PHY	1	/* its a CS8952 PHY		*/
 /************************************************************
  * RTC
  ***********************************************************/

include/configs/integratorap.h

@@ -58,7 +58,7 @@
 /*
  * PL010 Configuration
  */
-#define CFG_PL010_SERIAL
+#define CONFIG_PL010_SERIAL
 #define CONFIG_CONS_INDEX	0
 #define CONFIG_BAUDRATE		38400
 #define CONFIG_PL01x_PORTS	{ (void *) (CFG_SERIAL0), (void *) (CFG_SERIAL1) }

include/configs/integratorcp.h

@@ -61,7 +61,7 @@
 /*
  * NS16550 Configuration
  */
-#define CFG_PL011_SERIAL
+#define CONFIG_PL011_SERIAL
 #define CONFIG_PL011_CLOCK	14745600
 #define CONFIG_PL01x_PORTS	{ (void *)CFG_SERIAL0, (void *)CFG_SERIAL1 }
 #define CONFIG_CONS_INDEX	0

include/configs/kilauea.h

@@ -223,6 +223,22 @@
  *----------------------------------------------------------------------*/
 #define CFG_MBYTES_SDRAM        (256)		/* 256MB			*/
 
+/*
+ * CONFIG_PPC4xx_DDR_AUTOCALIBRATION
+ *
+ * Note: DDR Autocalibration Method_A scans the full range of possible PPC4xx
+ *       SDRAM Controller DDR autocalibration values and takes a lot longer
+ *       to run than Method_B.
+ * (See the Method_A and Method_B algorithm discription in the file:
+ *	cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c)
+ * Define CONFIG_PPC4xx_DDR_METHOD_A to use DDR autocalibration Method_A
+ *
+ * DDR Autocalibration Method_B is the default.
+ */
+#define	CONFIG_PPC4xx_DDR_AUTOCALIBRATION	/* IBM DDR autocalibration */
+#define	DEBUG_PPC4xx_DDR_AUTOCALIBRATION	/* dynamic DDR autocal debug */
+#undef	CONFIG_PPC4xx_DDR_METHOD_A
+
 #define	CFG_SDRAM0_MB0CF_BASE	((  0 << 20) + CFG_SDRAM_BASE)
 
 /* DDR1/2 SDRAM Device Control Register Data Values */
@@ -386,6 +402,9 @@
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
 #define CONFIG_PHY1_ADDR	2
 
+/* Debug messages for the DDR autocalibration */
+#define CONFIG_AUTOCALIB		"silent\0"  /* default is non-verbose */
+
 /*
  * Default environment variables
  */

include/configs/ml507.h

@@ -17,106 +17,33 @@
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
-/*
+
-#define DEBUG
+/*CPU*/
-#define ET_DEBUG
-*/
- /*CPU*/
-#define CONFIG_XILINX_ML507	1
-#define CONFIG_XILINX_440	1
 #define CONFIG_440		1
-#define CONFIG_4xx		1
+#define CONFIG_XILINX_ML507	1
 #include "../board/xilinx/ml507/xparameters.h"
 
 /*Mem Map*/
-#define CFG_SDRAM_BASE		0x0
 #define CFG_SDRAM_SIZE_MB	256
-#define CFG_MONITOR_BASE	TEXT_BASE
-#define CFG_MONITOR_LEN		( 192 * 1024 )
-#define CFG_MALLOC_LEN		( CFG_ENV_SIZE + 128 * 1024 )
-
-/*Uart*/
-#define CONFIG_XILINX_UARTLITE
-#define CONFIG_BAUDRATE		XPAR_UARTLITE_0_BAUDRATE
-#define CFG_BAUDRATE_TABLE	{ XPAR_UARTLITE_0_BAUDRATE }
-#define CONFIG_SERIAL_BASE	XPAR_UARTLITE_0_BASEADDR
-
-/*Cmd*/
-#include <config_cmd_default.h>
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_JFFS2
-#define CONFIG_JFFS2_CMDLINE
-#undef CONFIG_CMD_I2C
-#undef CONFIG_CMD_DTT
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_PING
-#undef CONFIG_CMD_DHCP
-#undef CONFIG_CMD_EEPROM
-#undef CONFIG_CMD_IMLS
 
 /*Env*/
-#define	CFG_ENV_IS_IN_FLASH
+#define	CFG_ENV_IS_IN_FLASH	1
 #define	CFG_ENV_SIZE		0x20000
 #define	CFG_ENV_SECT_SIZE	0x20000
 #define CFG_ENV_OFFSET		0x340000
 #define CFG_ENV_ADDR		(XPAR_FLASH_MEM0_BASEADDR+CFG_ENV_OFFSET)
 
 /*Misc*/
-#define CONFIG_BOOTDELAY	5		/* autoboot after 5 seconds     */
+#define CFG_PROMPT		"ml507:/# "	/* Monitor Command Prompt    */
-#define CFG_LONGHELP				/* undef to save memory         */
-#define CFG_PROMPT		"board:/# "	/* Monitor Command Prompt       */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size      */
-#else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size      */
-#endif
-#define CFG_PBSIZE		( CFG_CBSIZE + sizeof( CFG_PROMPT ) + 16 )
-#define CFG_MAXARGS		16		/* max number of command args   */
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START	0x00400000	/* memtest works on           */
-#define CFG_MEMTEST_END		0x00C00000	/* 4 ... 12 MB in DRAM        */
-#define CFG_LOAD_ADDR		0x00400000	/* default load address       */
-#define CFG_EXTBDINFO		1		/* Extended board_into (bd_t) */
-#define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */
-#define CONFIG_CMDLINE_EDITING			/* add command line history     */
-#define CONFIG_AUTO_COMPLETE			/* add autocompletion support   */
-#define CONFIG_LOOPW				/* enable loopw command         */
-#define CONFIG_MX_CYCLIC			/* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK		/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE			/* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET			/* don't print console @ startup */
-#define CFG_HUSH_PARSER				/* Use the HUSH parser          */
-#define	CFG_PROMPT_HUSH_PS2	"> "
-#define CONFIG_LOADS_ECHO			/* echo on for serial download  */
-#define CFG_LOADS_BAUD_CHANGE			/* allow baudrate change        */
-#define CFG_BOOTMAPSZ		( 8 << 20 )	/* Initial Memory map for Linux */
 #define CONFIG_PREBOOT		"echo U-Boot is up and runnining;"
 
-/*Stack*/
-#define CFG_INIT_RAM_ADDR	0x800000	/* Initial RAM address    */
-#define CFG_INIT_RAM_END	0x2000		/* End of used area in RAM  */
-#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data   */
-#define CFG_GBL_DATA_OFFSET	( CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE )
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
-/*Speed*/
-#define CONFIG_SYS_CLK_FREQ	XPAR_CORE_CLOCK_FREQ_HZ
-
 /*Flash*/
-#define	CFG_FLASH_BASE		XPAR_FLASH_MEM0_BASEADDR
 #define	CFG_FLASH_SIZE		(32*1024*1024)
-#define	CFG_FLASH_CFI		1
-#define	CONFIG_FLASH_CFI_DRIVER	1
-#define	CFG_FLASH_EMPTY_INFO	1
-#define	CFG_MAX_FLASH_BANKS	1
 #define	CFG_MAX_FLASH_SECT	259
-#define	CFG_FLASH_PROTECTION
 #define MTDIDS_DEFAULT		"nor0=ml507-flash"
 #define MTDPARTS_DEFAULT	"mtdparts=ml507-flash:-(user)"
 
+/*Generic Configs*/
+#include <configs/xilinx-ppc440.h>
 
 #endif						/* __CONFIG_H */

include/configs/sc520_cdp.h

@@ -28,6 +28,7 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#define GRUSS_TESTING
 /*
  * High Level Configuration Options
  * (easy to change)
@@ -81,7 +82,11 @@
 #include <config_cmd_default.h>
 
 #define CONFIG_CMD_PCI
+#ifndef GRUSS_TESTING
 #define CONFIG_CMD_SATA
+#else
+#undef CONFIG_CMD_SATA
+#endif
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_EEPROM
@@ -175,10 +180,18 @@
 /************************************************************
 *SATA/Native Stuff
 ************************************************************/
+#ifndef GRUSS_TESTING
 #define CFG_SATA_MAXBUS         2       /*Max Sata buses supported */
 #define CFG_SATA_DEVS_PER_BUS   2      /*Max no. of devices per bus/port */
 #define CFG_SATA_MAX_DEVICE     (CFG_SATA_MAXBUS* CFG_SATA_DEVS_PER_BUS)
 #define CONFIG_ATA_PIIX		1       /*Supports ata_piix driver */
+#else
+#undef CFG_SATA_MAXBUS
+#undef CFG_SATA_DEVS_PER_BUS
+#undef CFG_SATA_MAX_DEVICE
+#undef CONFIG_ATA_PIIX
+#endif
+
 
 /************************************************************
  * DISK Partition support
@@ -190,7 +203,11 @@
 /************************************************************
  * Video/Keyboard support
  ************************************************************/
+#ifndef GRUSS_TESTING
 #define CONFIG_VIDEO			/* To enable video controller support */
+#else
+#undef CONFIG_VIDEO
+#endif
 #define CONFIG_I8042_KBD
 #define CFG_ISA_IO 0
 
@@ -203,6 +220,7 @@
 /*
  * PCI stuff
  */
+#ifndef GRUSS_TESTING
 #define CONFIG_PCI                                /* include pci support */
 #define CONFIG_PCI_PNP                            /* pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW
@@ -211,5 +229,11 @@
 #define	CFG_SECOND_PCI_IRQ  9
 #define CFG_THIRD_PCI_IRQ   11
 #define	CFG_FORTH_PCI_IRQ   15
+#else
+#undef CONFIG_PCI
+#undef CONFIG_PCI_PNP
+#undef CONFIG_PCI_SCAN_SHOW
+#endif
+
 
 #endif	/* __CONFIG_H */

include/configs/stxxtc.h

@@ -580,7 +580,6 @@ typedef unsigned int led_id_t;
 /* use board specific hardware */
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 #define CONFIG_HW_WATCHDOG
-#define CONFIG_SHOW_ACTIVITY
 
 /*****************************************************************************/
 

include/configs/v5fx30teval.h

@@ -0,0 +1,49 @@
+/*
+ * (C) Copyright 2008
+ *  Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+ *  This work has been supported by: QTechnology  http://qtec.com/
+ *  This program is free software: you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation, either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*CPU*/
+#define CONFIG_440		1
+#define CONFIG_XILINX_ML507	1
+#include "../board/avnet/v5fx30teval/xparameters.h"
+
+/*Mem Map*/
+#define CFG_SDRAM_SIZE_MB	64
+
+/*Env*/
+#define	CFG_ENV_IS_IN_FLASH	1
+#define	CFG_ENV_SIZE		0x20000
+#define	CFG_ENV_SECT_SIZE	0x20000
+#define CFG_ENV_OFFSET		0x1A0000
+#define CFG_ENV_ADDR		(XPAR_FLASH_MEM0_BASEADDR+CFG_ENV_OFFSET)
+
+/*Misc*/
+#define CFG_PROMPT		"v5fx30t:/# "	/* Monitor Command Prompt    */
+#define CONFIG_PREBOOT		"echo U-Boot is up and runnining;"
+
+/*Flash*/
+#define	CFG_FLASH_SIZE		(16*1024*1024)
+#define	CFG_MAX_FLASH_SECT	131
+#define MTDIDS_DEFAULT		"nor0=v5fx30t-flash"
+#define MTDPARTS_DEFAULT	"mtdparts=v5fx30t-flash:-(user)"
+
+/*Generic Configs*/
+#include <configs/xilinx-ppc440.h>
+
+#endif						/* __CONFIG_H */

include/configs/versatile.h

@@ -86,7 +86,7 @@
 /*
  * NS16550 Configuration
  */
-#define CFG_PL011_SERIAL
+#define CONFIG_PL011_SERIAL
 #define CONFIG_PL011_CLOCK	24000000
 #define CONFIG_PL01x_PORTS	{ (void *)CFG_SERIAL0, (void *)CFG_SERIAL1 }
 #define CONFIG_CONS_INDEX	0

include/configs/xilinx-ppc440-generic.h

@@ -0,0 +1,49 @@
+/*
+ * (C) Copyright 2008
+ *  Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+ *  This work has been supported by: QTechnology  http://qtec.com/
+ *  This program is free software: you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation, either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*CPU*/
+#define CONFIG_440			1
+#define CONFIG_XILINX_PPC440_GENERIC	1
+#include "../board/xilinx/ppc440-generic/xparameters.h"
+
+/*Mem Map*/
+#define CFG_SDRAM_SIZE_MB	256
+
+/*Env*/
+#define	CFG_ENV_IS_IN_FLASH	1
+#define	CFG_ENV_SIZE		0x20000
+#define	CFG_ENV_SECT_SIZE	0x20000
+#define CFG_ENV_OFFSET		0x340000
+#define CFG_ENV_ADDR		(XPAR_FLASH_MEM0_BASEADDR+CFG_ENV_OFFSET)
+
+/*Misc*/
+#define CFG_PROMPT		"board:/# "	/* Monitor Command Prompt    */
+#define CONFIG_PREBOOT		"echo U-Boot is up and runnining;"
+
+/*Flash*/
+#define	CFG_FLASH_SIZE		(32*1024*1024)
+#define	CFG_MAX_FLASH_SECT	259
+#define MTDIDS_DEFAULT		"nor0=ml507-flash"
+#define MTDPARTS_DEFAULT	"mtdparts=ml507-flash:-(user)"
+
+/*Generic Configs*/
+#include <configs/xilinx-ppc440.h>
+
+#endif						/* __CONFIG_H */

include/configs/xilinx-ppc440.h

@@ -0,0 +1,106 @@
+/*
+ * (C) Copyright 2008
+ *  Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es
+ *  This work has been supported by: QTechnology  http://qtec.com/
+ *  This program is free software: you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation, either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef __CONFIG_GEN_H
+#define __CONFIG_GEN_H
+/*
+#define DEBUG
+#define ET_DEBUG
+*/
+ /*CPU*/
+#define CONFIG_XILINX_440	1
+#define CONFIG_440		1
+#define CONFIG_4xx		1
+
+/*Mem Map*/
+#define CFG_SDRAM_BASE		0x0
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MONITOR_LEN		(192 * 1024)
+#define CFG_MALLOC_LEN		(CFG_ENV_SIZE + 128 * 1024)
+
+/*Uart*/
+#define CONFIG_XILINX_UARTLITE
+#define CONFIG_BAUDRATE		XPAR_UARTLITE_0_BAUDRATE
+#define CFG_BAUDRATE_TABLE	{ XPAR_UARTLITE_0_BAUDRATE }
+#define CONFIG_SERIAL_BASE	XPAR_UARTLITE_0_BASEADDR
+
+/*Cmd*/
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_JFFS2
+#define CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_SPI
+#undef CONFIG_CMD_I2C
+#undef CONFIG_CMD_DTT
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_PING
+#undef CONFIG_CMD_DHCP
+#undef CONFIG_CMD_EEPROM
+#undef CONFIG_CMD_IMLS
+
+/*Misc*/
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds     */
+#define CFG_LONGHELP			/* undef to save memory         */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
+#else
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size      */
+#endif
+#define CFG_PBSIZE		(CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
+#define CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_MEMTEST_START	0x00400000	/* memtest works on           */
+#define CFG_MEMTEST_END		0x00C00000	/* 4 ... 12 MB in DRAM        */
+#define CFG_LOAD_ADDR		0x00400000	/* default load address       */
+#define CFG_EXTBDINFO		1	/* Extended board_into (bd_t) */
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING		/* add command line history     */
+#define CONFIG_AUTO_COMPLETE		/* add autocompletion support   */
+#define CONFIG_LOOPW			/* enable loopw command         */
+#define CONFIG_MX_CYCLIC		/* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE		/* include version env variable */
+#define CFG_CONSOLE_INFO_QUIET		/* don't print console @ startup */
+#define CFG_HUSH_PARSER			/* Use the HUSH parser          */
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#define CONFIG_LOADS_ECHO		/* echo on for serial download  */
+#define CFG_LOADS_BAUD_CHANGE		/* allow baudrate change        */
+#define CFG_BOOTMAPSZ		(8 << 20)/* Initial Memory map for Linux */
+
+/*Stack*/
+#define CFG_INIT_RAM_ADDR	0x800000	/* Initial RAM address    */
+#define CFG_INIT_RAM_END	0x2000		/* End of used area in RAM  */
+#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data   */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+/*Speed*/
+#define CONFIG_SYS_CLK_FREQ	XPAR_CORE_CLOCK_FREQ_HZ
+
+/*Flash*/
+#define	CFG_FLASH_BASE		XPAR_FLASH_MEM0_BASEADDR
+#define	CFG_FLASH_CFI		1
+#define	CONFIG_FLASH_CFI_DRIVER	1
+#define	CFG_FLASH_EMPTY_INFO	1
+#define	CFG_MAX_FLASH_BANKS	1
+#define	CFG_FLASH_PROTECTION
+
+#endif						/* __CONFIG_H */

include/image.h

@@ -85,6 +85,7 @@
 #define IH_OS_RTEMS		18	/* RTEMS	*/
 #define IH_OS_ARTOS		19	/* ARTOS	*/
 #define IH_OS_UNITY		20	/* Unity OS	*/
+#define IH_OS_INTEGRITY		21	/* INTEGRITY	*/
 
 /*
  * CPU Architecture Codes (supported by Linux)
@@ -573,6 +574,7 @@ int fit_image_hash_set_value (void *fit, int noffset, uint8_t *value,
 				int value_len);
 
 int fit_image_check_hashes (const void *fit, int noffset);
+int fit_all_image_check_hashes (const void *fit);
 int fit_image_check_os (const void *fit, int noffset, uint8_t os);
 int fit_image_check_arch (const void *fit, int noffset, uint8_t arch);
 int fit_image_check_type (const void *fit, int noffset, uint8_t type);

include/onenand_uboot.h

@@ -15,6 +15,7 @@
 #define __UBOOT_ONENAND_H
 
 #include <linux/types.h>
+#include <linux/mtd/mtd.h>
 
 struct mtd_info;
 struct erase_info;

include/ppc440.h

@@ -2064,19 +2064,6 @@
 
 #ifndef __ASSEMBLY__
 
-static inline u32 get_mcsr(void)
-{
-	u32 val;
-
-	asm volatile("mfspr %0, 0x23c" : "=r" (val) :);
-	return val;
-}
-
-static inline void set_mcsr(u32 val)
-{
-	asm volatile("mtspr 0x23c, %0" : "=r" (val) :);
-}
-
 #endif	/* _ASMLANGUAGE */
 
 #endif	/* __PPC440_H__ */

include/ppc4xx.h

@@ -203,6 +203,19 @@ typedef struct
 	unsigned long pllPlbDiv;
 } PPC4xx_SYS_INFO;
 
+static inline u32 get_mcsr(void)
+{
+	u32 val;
+
+	asm volatile("mfspr %0, 0x23c" : "=r" (val) :);
+	return val;
+}
+
+static inline void set_mcsr(u32 val)
+{
+	asm volatile("mtspr 0x23c, %0" : "=r" (val) :);
+}
+
 #endif	/* __ASSEMBLY__ */
 
 #endif	/* __PPC4XX_H__ */

include/ppc4xx_enet.h

@@ -376,6 +376,7 @@ typedef struct emac_4xx_hw_st {
 #define EMAC_M1_APP		(0x08000000)
 #define EMAC_M1_RSVD		(0x06000000)
 #define EMAC_M1_IST		(0x01000000)
+#define EMAC_M1_MF_1000GPCS	(0x00C00000)
 #define EMAC_M1_MF_1000MBPS	(0x00800000)	/* 0's for 10MBPS */
 #define EMAC_M1_MF_100MBPS	(0x00400000)
 #define EMAC_M1_RFS_MASK	(0x00380000)
@@ -394,6 +395,8 @@ typedef struct emac_4xx_hw_st {
 #define EMAC_M1_MWSW		(0x00007000)
 #define EMAC_M1_JUMBO_ENABLE	(0x00000800)
 #define EMAC_M1_IPPA		(0x000007c0)
+#define EMAC_M1_IPPA_SET(id)	(((id) & 0x1f) << 6)
+#define EMAC_M1_IPPA_GET(id)	(((id) >> 6) & 0x1f)
 #define EMAC_M1_OBCI_GT100	(0x00000020)
 #define EMAC_M1_OBCI_100	(0x00000018)
 #define EMAC_M1_OBCI_83		(0x00000010)

lib_arm/bootm.c

@@ -62,7 +62,6 @@ int do_bootm_linux(int flag, int argc, char *argv[], bootm_headers_t *images)
 	char	*s;
 	int	machid = bd->bi_arch_number;
 	void	(*theKernel)(int zero, int arch, uint params);
-	int	ret;
 
 #ifdef CONFIG_CMDLINE_TAG
 	char *commandline = getenv ("bootargs");
@@ -125,7 +124,7 @@ int do_bootm_linux(int flag, int argc, char *argv[], bootm_headers_t *images)
 
 	theKernel (0, machid, bd->bi_boot_params);
 	/* does not return */
-error:
+
 	return 1;
 }
 

lib_i386/bios_setup.c

@@ -140,8 +140,9 @@ int bios_setup(void)
 {
 	static int done=0;
 	int vector;
+#ifdef CONFIG_PCI
 	struct pci_controller *pri_hose;
-
+#endif
 	if (done) {
 		return 0;
 	}
@@ -223,12 +224,13 @@ int bios_setup(void)
 	 * (This, ofcause break on multi hose systems,
 	 *  but our PCI BIOS only support one hose anyway)
 	 */
+#ifdef CONFIG_PCI
 	pri_hose = pci_bus_to_hose(0);
 	if (NULL != pri_hose) {
 		/* fill in last pci bus number for use by the realmode
 		 * PCI BIOS */
 		RELOC_16_BYTE(0xf000, pci_last_bus) = pri_hose->last_busno;
 	}
-
+#endif
 	return 0;
 }

lib_i386/board.c

@@ -213,7 +213,7 @@ init_fnc_t *init_sequence[] = {
 	NULL,
 };
 
-gd_t *global_data;
+gd_t *gd;
 
 void start_i386boot (void)
 {
@@ -226,7 +226,7 @@ void start_i386boot (void)
 
 	show_boot_progress(0x21);
 
-	gd = global_data = &gd_data;
+	gd = &gd_data;
 	/* compiler optimization barrier needed for GCC >= 3.4 */
 	__asm__ __volatile__("": : :"memory");
 
@@ -266,7 +266,7 @@ void start_i386boot (void)
 		int i;
 		ulong reg;
 		char *s, *e;
-		uchar tmp[64];
+		char tmp[64];
 
 		i = getenv_r ("ethaddr", tmp, sizeof (tmp));
 		s = (i > 0) ? tmp : NULL;
@@ -412,7 +412,10 @@ void hang (void)
 unsigned long do_go_exec (ulong (*entry)(int, char *[]), int argc, char *argv[])
 {
 	/*
-	 * Nios function pointers are address >> 1
+	 * TODO: Test this function - changed to fix compiler error.
+	 * Original code was:
+	 *   return (entry >> 1) (argc, argv);
+	 * with a comment about Nios function pointers are address >> 1
 	 */
-	return (entry >> 1) (argc, argv);
+	return (entry) (argc, argv);
 }

lib_i386/bootm.c

@@ -34,7 +34,7 @@ int do_bootm_linux(int flag, int argc, char *argv[], bootm_headers_t *images)
 	void		*base_ptr;
 	ulong		os_data, os_len;
 	image_header_t	*hdr;
-	int		ret;
+
 #if defined(CONFIG_FIT)
 	const void	*data;
 	size_t		len;

lib_i386/video_bios.c

@@ -136,6 +136,8 @@ static u32 probe_pci_video(void)
 
 #endif
 
+#ifdef CONFIG_VIDEO
+
 static int probe_isa_video(void)
 {
 	u32 ptr;
@@ -217,3 +219,4 @@ int video_bios_init(void)
 	return 1;
 
 }
+#endif

lib_mips/Makefile

@@ -28,7 +28,11 @@ LIB	= $(obj)lib$(ARCH).a
 SOBJS-y	+=
 
 COBJS-y	+= board.o
+ifeq ($(CONFIG_QEMU_MIPS),y)
+COBJS-y	+= bootm_qemu_mips.o
+else
 COBJS-y	+= bootm.o
+endif
 COBJS-y	+= time.o
 
 SRCS	:= $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)

lib_mips/bootm.c

@@ -73,7 +73,7 @@ int do_bootm_linux(int flag, int argc, char *argv[], bootm_headers_t *images)
 	linux_env_set ("memsize", env_buf);
 
 	sprintf (env_buf, "0x%08X", (uint) UNCACHED_SDRAM (images->rd_start));
-	linux_env_set ("images->rd_start", env_buf);
+	linux_env_set ("initrd_start", env_buf);
 
 	sprintf (env_buf, "0x%X", (uint) (images->rd_end - images->rd_start));
 	linux_env_set ("initrd_size", env_buf);