Merge git://git.denx.de/u-boot-marvell

arch/arm/dts/armada-385-amc.dts

@@ -53,7 +53,7 @@
 
 	aliases {
 		ethernet0 = &eth0;
-		ethernet1 = &eth1;
+		ethernet1 = &eth2;
 		i2c0 = &i2c0;
 		spi1 = &spi1;
 	};

board/solidrun/clearfog/README

@@ -17,16 +17,29 @@ $ sudo dd if=u-boot-spl.kwb of=/dev/sdX bs=512 seek=1
 Please use the correct device node for your setup instead
 of "/dev/sdX" here!
 
+Boot selection:
+---------------
+
+Before powering up the board, boot selection should be done via the SW1 dip
+switch (0: OFF, 1: ON):
+
+ - SPI:     00010
+ - SD/eMMC: 00111
+ - M.2 SSD: 11100
+ - UART:    01001 [1]
+
+[1]: According to SolidRun's manual, 11110 should be used for UART booting on
+     the ClearFog 'Pro' variant.
+     However, this doesn't work (anymore) at least on Rev. 2.1 (but '01001' as
+     mentionend for the 'Base' variant does).
+
 Boot from UART:
 ---------------
 
 Connect the on-board micro-USB (CF Pro: CON11, CF Base: CON5)
 to your host.
 
-Set the SW1 DIP switches to UART boot (0: OFF, 1: ON):
-
-  ClearFog Base: 01001
-  ClearFog Pro:  11110
+Set the SW1 DIP switches to UART boot (see above).
 
 Run the following command to initiate U-Boot download:
 

configs/mvebu_db-88f3720_defconfig

@@ -3,6 +3,7 @@ CONFIG_ARCH_MVEBU=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_MVEBU_ARMADA_37XX=y
 CONFIG_DEFAULT_DEVICE_TREE="armada-3720-db"
+CONFIG_DISTRO_DEFAULTS=y
 CONFIG_DEBUG_UART=y
 CONFIG_AHCI=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set

configs/mvebu_espressobin-88f3720_defconfig

@@ -3,6 +3,7 @@ CONFIG_ARCH_MVEBU=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_MVEBU_ARMADA_37XX=y
 CONFIG_DEFAULT_DEVICE_TREE="armada-3720-espressobin"
+CONFIG_DISTRO_DEFAULTS=y
 CONFIG_DEBUG_UART=y
 CONFIG_AHCI=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set

drivers/net/Kconfig

@@ -160,12 +160,12 @@ config FTMAC100
 	  This MAC is present in Andestech SoCs.
 
 config MVNETA
-	bool "Marvell Armada 385 network interface support"
-	depends on ARMADA_XP || ARMADA_38X
+	bool "Marvell Armada XP/385/3700 network interface support"
+	depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
 	select PHYLIB
 	help
 	  This driver supports the network interface units in the
-	  Marvell ARMADA XP and 38X SoCs
+	  Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
 
 config MVPP2
 	bool "Marvell Armada 375/7K/8K network interface support"

drivers/pinctrl/mvebu/Kconfig

@@ -1,14 +1,14 @@
 if ARCH_MVEBU
 
 config PINCTRL_ARMADA_37XX
-	depends on ARMADA_3700
+	depends on ARMADA_3700 && PINCTRL_FULL
 	bool "Armada 37xx pin control driver"
 	help
 	   Support pin multiplexing and pin configuration control on
 	   Marvell's Armada-37xx SoC.
 
 config PINCTRL_ARMADA_8K
-	depends on ARMADA_8K
+	depends on ARMADA_8K && PINCTRL_FULL
 	bool "Armada 7k/8k pin control driver"
 	help
 	   Support pin multiplexing and pin configuration control on

include/configs/mvebu_armada-37xx.h

@@ -44,9 +44,6 @@
 /*
  * Other required minimal configurations
  */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
 #define CONFIG_ARCH_CPU_INIT		/* call arch_cpu_init() */
 #define CONFIG_SYS_LOAD_ADDR	0x00800000	/* default load adr- 8M */
 #define CONFIG_SYS_MEMTEST_START 0x00800000	/* 8M */
@@ -107,4 +104,24 @@
 
 #define CONFIG_SUPPORT_VFAT
 
+#include <config_distro_defaults.h>
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 1) \
+	func(MMC, mmc, 0) \
+	func(USB, usb, 0) \
+	func(SCSI, scsi, 0) \
+	func(PXE, pxe, na) \
+	func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+#define CONFIG_EXTRA_ENV_SETTINGS	\
+	"scriptaddr=0x4d00000\0"	\
+	"pxefile_addr_r=0x4e00000\0"	\
+	"fdt_addr_r=0x4f00000\0"	\
+	"kernel_addr_r=0x5000000\0"	\
+	"ramdisk_addr_r=0x8000000\0"	\
+	BOOTENV
+
 #endif /* _CONFIG_MVEBU_ARMADA_37XX_H */

tools/mrvl_uart.sh

@@ -0,0 +1,119 @@
+#!/bin/bash
+#
+######################################################
+# Copyright (C) 2016 Marvell International Ltd.
+#
+# SPDX-License-Identifier:	GPL-2.0
+# https://spdx.org/licenses
+#
+# Author: Konstantin Porotchkin kostap@marvell.com
+#
+# Version 0.3
+#
+# UART recovery downloader for Armada SoCs
+#
+######################################################
+
+port=$1
+file=$2
+speed=$3
+
+pattern_repeat=1500
+default_baudrate=115200
+tmpfile=/tmp/xmodem.pattern
+tools=( dd stty sx minicom )
+
+case "$3" in
+    2)
+        fast_baudrate=230400
+        prefix="\xF2"
+        ;;
+    4)
+        fast_baudrate=460800
+        prefix="\xF4"
+        ;;
+    8)
+    	fast_baudrate=921600
+        prefix="\xF8"
+        ;;
+    *)
+    	fast_baudrate=$default_baudrate
+        prefix="\xBB"
+esac
+
+if [[ -z "$port" || -z "$file" ]]
+then
+    echo -e "\nMarvell recovery image downloader for Armada SoC family."
+    echo -e "Command syntax:"
+    echo -e "\t$(basename $0) <port> <file> [2|4|8]"
+    echo -e "\tport  - serial port the target board connected to"
+    echo -e "\tfile  - recovery boot image for target download"
+    echo -e "\t2|4|8 - times to increase the default serial port speed by"
+    echo -e "For example - load the image over ttyUSB0 @ 460800 baud:"
+    echo -e "$(basename $0) /dev/ttyUSB0 /tmp/flash-image.bin 4\n"
+    echo -e "=====WARNING====="
+    echo -e "- The speed-up option is not awailable in SoC families prior to A8K+"
+    echo -e "- This utility is not compatible with Armada 37xx SoC family\n"
+fi
+
+# Sanity checks
+if [ -c "$port" ]
+then
+   echo -e "Using device connected on serial port \"$port\""
+else
+   echo "Wrong serial port name!"
+   exit 1
+fi
+
+if [ -f "$file" ]
+then
+   echo -e "Loading flash image file \"$file\""
+else
+   echo "File $file does not exist!"
+   exit 1
+fi
+
+# Verify required tools installation
+for tool in ${tools[@]}
+do
+    toolname=`which $tool`
+    if [ -z "$toolname" ]
+    then
+        echo -e "Missing installation of \"$tool\" --> Exiting"
+        exit 1
+    fi
+done
+
+
+echo -e "Recovery will run at $fast_baudrate baud"
+echo -e "========================================"
+
+if [ -f "$tmpfile" ]
+then
+    rm -f $tmpfile
+fi
+
+# Send the escape sequence to target board using default debug port speed
+stty -F $port raw ignbrk time 5 $default_baudrate
+counter=0
+while [ $counter -lt $pattern_repeat ]; do
+    echo -n -e "$prefix\x11\x22\x33\x44\x55\x66\x77" >> $tmpfile
+    let counter=counter+1
+done
+
+echo -en "Press the \"Reset\" button on the target board and "
+echo -en "the \"Enter\" key on the host keyboard simultaneously"
+read
+dd if=$tmpfile of=$port &>/dev/null
+
+# Speed up the binary image transfer
+stty -F $port raw ignbrk time 5 $fast_baudrate
+sx -vv $file > $port < $port
+#sx-at91 $port $file
+
+# return the port to the default speed
+stty -F $port raw ignbrk time 5 $default_baudrate
+
+# Optional - fire up Minicom
+minicom -D $port
+