u-boot/include/configs/M5235EVB.h

134 lines
3.8 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuation settings for the Freescale MCF5329 FireEngine board.
*
* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
* TsiChung Liew (Tsi-Chung.Liew@freescale.com)
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef _M5235EVB_H
#define _M5235EVB_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CFG_SYS_UART_PORT (0)
/* I2C */
#define CFG_SYS_I2C_PINMUX_REG (gpio->par_qspi)
#define CFG_SYS_I2C_PINMUX_CLR ~(GPIO_PAR_FECI2C_SCL_MASK | GPIO_PAR_FECI2C_SDA_MASK)
#define CFG_SYS_I2C_PINMUX_SET (GPIO_PAR_FECI2C_SCL_I2CSCL | GPIO_PAR_FECI2C_SDA_I2CSDA)
/* this must be included AFTER the definition of CONFIG COMMANDS (if any) */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"loadaddr=10000\0" \
"u-boot=u-boot.bin\0" \
"load=tftp ${loadaddr) ${u-boot}\0" \
"upd=run load; run prog\0" \
"prog=prot off ffe00000 ffe3ffff;" \
"era ffe00000 ffe3ffff;" \
"cp.b ${loadaddr} ffe00000 ${filesize};"\
"save\0" \
""
#define CONFIG_PRAM 512 /* 512 KB */
#define CFG_SYS_CLK 75000000
#define CFG_SYS_CPU_CLK CFG_SYS_CLK * 2
#define CFG_SYS_MBAR 0x40000000
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_SYS_INIT_RAM_ADDR 0x20000000
#define CFG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
#define CFG_SYS_INIT_RAM_CTRL 0x21
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CFG_SYS_SDRAM_BASE 0x00000000
#define CFG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
/* Initial Memory map for Linux */
#define CFG_SYS_BOOTMAPSZ (CFG_SYS_SDRAM_BASE + (CFG_SYS_SDRAM_SIZE << 20))
/*-----------------------------------------------------------------------
* FLASH organization
*/
#ifdef CONFIG_SYS_FLASH_CFI
# define CFG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */
#endif
#define CFG_SYS_FLASH_BASE (CFG_SYS_CS0_BASE)
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
#define LDS_BOARD_TEXT \
. = DEFINED(env_offset) ? env_offset : .; \
env/embedded.o(.text);
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
CFG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
CFG_SYS_INIT_RAM_SIZE - 4)
#define CFG_SYS_ICACHE_INV (CF_CACR_CINV)
#define CFG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \
CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
#define CFG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \
CF_CACR_CEIB | CF_CACR_DCM | \
CF_CACR_EUSP)
/*-----------------------------------------------------------------------
* Chipselect bank definitions
*/
/*
* CS0 - NOR Flash 1, 2, 4, or 8MB
* CS1 - Available
* CS2 - Available
* CS3 - Available
* CS4 - Available
* CS5 - Available
* CS6 - Available
* CS7 - Available
*/
#ifdef CONFIG_NORFLASH_PS32BIT
# define CFG_SYS_CS0_BASE 0xFFC00000
# define CFG_SYS_CS0_MASK 0x003f0001
# define CFG_SYS_CS0_CTRL 0x00001D00
#else
# define CFG_SYS_CS0_BASE 0xFFE00000
# define CFG_SYS_CS0_MASK 0x001f0001
# define CFG_SYS_CS0_CTRL 0x00001D80
#endif
#endif /* _M5329EVB_H */