2002-08-26 22:36:39 +00:00
|
|
|
/*
|
2008-09-16 16:02:19 +00:00
|
|
|
* (C) Copyright 2000-2008
|
2002-08-26 22:36:39 +00:00
|
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
|
|
*
|
2013-07-08 07:37:19 +00:00
|
|
|
* SPDX-License-Identifier: GPL-2.0+
|
2002-08-26 22:36:39 +00:00
|
|
|
*/
|
|
|
|
|
|
|
|
#include <common.h>
|
2010-02-09 14:50:21 +00:00
|
|
|
#include <hwconfig.h>
|
2002-08-26 22:36:39 +00:00
|
|
|
#include <mpc8xx.h>
|
2004-01-16 00:30:56 +00:00
|
|
|
#ifdef CONFIG_PS2MULT
|
|
|
|
#include <ps2mult.h>
|
|
|
|
#endif
|
2002-08-26 22:36:39 +00:00
|
|
|
|
2010-02-09 14:50:21 +00:00
|
|
|
#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
|
|
|
|
#include <libfdt.h>
|
|
|
|
#endif
|
|
|
|
|
2008-09-16 16:02:19 +00:00
|
|
|
extern flash_info_t flash_info[]; /* FLASH chips info */
|
|
|
|
|
2006-03-31 16:32:53 +00:00
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
static long int dram_size (long int, long int *, long int);
|
|
|
|
|
|
|
|
#define _NOT_USED_ 0xFFFFFFFF
|
|
|
|
|
2007-09-26 15:55:54 +00:00
|
|
|
/* UPM initialization table for SDRAM: 40, 50, 66 MHz CLKOUT @ CAS latency 2, tWR=2 */
|
2002-08-26 22:36:39 +00:00
|
|
|
const uint sdram_table[] =
|
|
|
|
{
|
|
|
|
/*
|
|
|
|
* Single Read. (Offset 0 in UPMA RAM)
|
|
|
|
*/
|
|
|
|
0x1F0DFC04, 0xEEAFBC04, 0x11AF7C04, 0xEFBAFC00,
|
|
|
|
0x1FF5FC47, /* last */
|
|
|
|
/*
|
|
|
|
* SDRAM Initialization (offset 5 in UPMA RAM)
|
|
|
|
*
|
|
|
|
* This is no UPM entry point. The following definition uses
|
|
|
|
* the remaining space to establish an initialization
|
|
|
|
* sequence, which is executed by a RUN command.
|
|
|
|
*
|
|
|
|
*/
|
|
|
|
0x1FF5FC34, 0xEFEABC34, 0x1FB57C35, /* last */
|
|
|
|
/*
|
|
|
|
* Burst Read. (Offset 8 in UPMA RAM)
|
|
|
|
*/
|
|
|
|
0x1F0DFC04, 0xEEAFBC04, 0x10AF7C04, 0xF0AFFC00,
|
|
|
|
0xF0AFFC00, 0xF1AFFC00, 0xEFBAFC00, 0x1FF5FC47, /* last */
|
|
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
|
|
/*
|
|
|
|
* Single Write. (Offset 18 in UPMA RAM)
|
|
|
|
*/
|
2007-09-26 15:55:54 +00:00
|
|
|
0x1F0DFC04, 0xEEABBC00, 0x11B77C04, 0xEFFAFC44,
|
|
|
|
0x1FF5FC47, /* last */
|
|
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_,
|
2002-08-26 22:36:39 +00:00
|
|
|
/*
|
|
|
|
* Burst Write. (Offset 20 in UPMA RAM)
|
|
|
|
*/
|
|
|
|
0x1F0DFC04, 0xEEABBC00, 0x10A77C00, 0xF0AFFC00,
|
2007-09-26 15:55:54 +00:00
|
|
|
0xF0AFFC00, 0xF0AFFC04, 0xE1BAFC44, 0x1FF5FC47, /* last */
|
2002-08-26 22:36:39 +00:00
|
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
|
|
/*
|
|
|
|
* Refresh (Offset 30 in UPMA RAM)
|
|
|
|
*/
|
|
|
|
0x1FFD7C84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
|
|
|
|
0xFFFFFC84, 0xFFFFFC07, /* last */
|
|
|
|
_NOT_USED_, _NOT_USED_,
|
|
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
|
|
/*
|
|
|
|
* Exception. (Offset 3c in UPMA RAM)
|
|
|
|
*/
|
2007-09-26 15:55:54 +00:00
|
|
|
0xFFFFFC07, /* last */
|
2002-08-26 22:36:39 +00:00
|
|
|
_NOT_USED_, _NOT_USED_, _NOT_USED_,
|
|
|
|
};
|
|
|
|
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Check Board Identity:
|
|
|
|
*
|
|
|
|
* Test TQ ID string (TQM8xx...)
|
|
|
|
* If present, check for "L" type (no second DRAM bank),
|
|
|
|
* otherwise "L" type is assumed as default.
|
|
|
|
*
|
2004-01-02 14:00:00 +00:00
|
|
|
* Set board_type to 'L' for "L" type, 'M' for "M" type, 0 else.
|
2002-08-26 22:36:39 +00:00
|
|
|
*/
|
|
|
|
|
|
|
|
int checkboard (void)
|
|
|
|
{
|
2011-05-04 10:32:28 +00:00
|
|
|
char buf[64];
|
|
|
|
int i;
|
|
|
|
int l = getenv_f("serial#", buf, sizeof(buf));
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
puts ("Board: ");
|
|
|
|
|
2011-05-04 10:32:28 +00:00
|
|
|
if (l < 0 || strncmp(buf, "TQM8", 4)) {
|
2002-08-26 22:36:39 +00:00
|
|
|
puts ("### No HW ID - assuming TQM8xxL\n");
|
|
|
|
return (0);
|
|
|
|
}
|
|
|
|
|
2011-05-04 10:32:28 +00:00
|
|
|
if ((buf[6] == 'L')) { /* a TQM8xxL type */
|
2002-08-26 22:36:39 +00:00
|
|
|
gd->board_type = 'L';
|
|
|
|
}
|
|
|
|
|
2011-05-04 10:32:28 +00:00
|
|
|
if ((buf[6] == 'M')) { /* a TQM8xxM type */
|
2004-01-02 14:00:00 +00:00
|
|
|
gd->board_type = 'M';
|
|
|
|
}
|
|
|
|
|
2011-05-04 10:32:28 +00:00
|
|
|
if ((buf[6] == 'D')) { /* a TQM885D type */
|
2006-07-12 13:26:01 +00:00
|
|
|
gd->board_type = 'D';
|
|
|
|
}
|
|
|
|
|
2011-05-04 10:32:28 +00:00
|
|
|
for (i = 0; i < l; ++i) {
|
|
|
|
if (buf[i] == ' ')
|
2002-08-26 22:36:39 +00:00
|
|
|
break;
|
2011-05-04 10:32:28 +00:00
|
|
|
putc (buf[i]);
|
2002-08-26 22:36:39 +00:00
|
|
|
}
|
2014-12-15 14:26:06 +00:00
|
|
|
|
2002-08-26 22:36:39 +00:00
|
|
|
putc ('\n');
|
|
|
|
|
|
|
|
return (0);
|
|
|
|
}
|
|
|
|
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
|
2008-06-09 21:03:40 +00:00
|
|
|
phys_size_t initdram (int board_type)
|
2002-08-26 22:36:39 +00:00
|
|
|
{
|
2008-10-16 13:01:15 +00:00
|
|
|
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
|
2002-08-26 22:36:39 +00:00
|
|
|
volatile memctl8xx_t *memctl = &immap->im_memctl;
|
2004-01-24 20:25:54 +00:00
|
|
|
long int size8, size9, size10;
|
2002-08-26 22:36:39 +00:00
|
|
|
long int size_b0 = 0;
|
|
|
|
long int size_b1 = 0;
|
|
|
|
|
|
|
|
upmconfig (UPMA, (uint *) sdram_table,
|
|
|
|
sizeof (sdram_table) / sizeof (uint));
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Preliminary prescaler for refresh (depends on number of
|
|
|
|
* banks): This value is selected for four cycles every 62.4 us
|
|
|
|
* with two SDRAM banks or four cycles every 31.2 us with one
|
|
|
|
* bank. It will be adjusted after memory sizing.
|
|
|
|
*/
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
/*
|
|
|
|
* The following value is used as an address (i.e. opcode) for
|
|
|
|
* the LOAD MODE REGISTER COMMAND during SDRAM initialisation. If
|
|
|
|
* the port size is 32bit the SDRAM does NOT "see" the lower two
|
|
|
|
* address lines, i.e. mar=0x00000088 -> opcode=0x00000022 for
|
|
|
|
* MICRON SDRAMs:
|
|
|
|
* -> 0 00 010 0 010
|
|
|
|
* | | | | +- Burst Length = 4
|
|
|
|
* | | | +----- Burst Type = Sequential
|
|
|
|
* | | +------- CAS Latency = 2
|
|
|
|
* | +----------- Operating Mode = Standard
|
|
|
|
* +-------------- Write Burst Mode = Programmed Burst Length
|
|
|
|
*/
|
|
|
|
memctl->memc_mar = 0x00000088;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at
|
|
|
|
* preliminary addresses - these have to be modified after the
|
|
|
|
* SDRAM size has been determined.
|
|
|
|
*/
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_or2 = CONFIG_SYS_OR2_PRELIM;
|
|
|
|
memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM;
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
#ifndef CONFIG_CAN_DRIVER
|
2004-01-02 14:00:00 +00:00
|
|
|
if ((board_type != 'L') &&
|
2006-07-12 13:26:01 +00:00
|
|
|
(board_type != 'M') &&
|
2007-09-26 15:55:56 +00:00
|
|
|
(board_type != 'D') ) { /* only one SDRAM bank on L, M and D modules */
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
|
|
|
|
memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
|
2002-08-26 22:36:39 +00:00
|
|
|
}
|
|
|
|
#endif /* CONFIG_CAN_DRIVER */
|
|
|
|
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
udelay (200);
|
|
|
|
|
|
|
|
/* perform SDRAM initializsation sequence */
|
|
|
|
|
|
|
|
memctl->memc_mcr = 0x80004105; /* SDRAM bank 0 */
|
|
|
|
udelay (1);
|
|
|
|
memctl->memc_mcr = 0x80004230; /* SDRAM bank 0 - execute twice */
|
|
|
|
udelay (1);
|
|
|
|
|
|
|
|
#ifndef CONFIG_CAN_DRIVER
|
2004-01-02 14:00:00 +00:00
|
|
|
if ((board_type != 'L') &&
|
2006-07-12 13:26:01 +00:00
|
|
|
(board_type != 'M') &&
|
2006-07-21 16:51:56 +00:00
|
|
|
(board_type != 'D') ) { /* only one SDRAM bank on L, M and D modules */
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_mcr = 0x80006105; /* SDRAM bank 1 */
|
|
|
|
udelay (1);
|
|
|
|
memctl->memc_mcr = 0x80006230; /* SDRAM bank 1 - execute twice */
|
|
|
|
udelay (1);
|
|
|
|
}
|
|
|
|
#endif /* CONFIG_CAN_DRIVER */
|
|
|
|
|
|
|
|
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
|
|
|
|
|
|
|
|
udelay (1000);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Check Bank 0 Memory Size for re-configuration
|
|
|
|
*
|
|
|
|
* try 8 column mode
|
|
|
|
*/
|
2008-10-16 13:01:15 +00:00
|
|
|
size8 = dram_size (CONFIG_SYS_MAMR_8COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
|
2004-01-02 14:00:00 +00:00
|
|
|
debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size8 >> 20);
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
udelay (1000);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* try 9 column mode
|
|
|
|
*/
|
2008-10-16 13:01:15 +00:00
|
|
|
size9 = dram_size (CONFIG_SYS_MAMR_9COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
|
2004-01-02 14:00:00 +00:00
|
|
|
debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size9 >> 20);
|
2002-08-26 22:36:39 +00:00
|
|
|
|
2004-01-24 20:25:54 +00:00
|
|
|
udelay(1000);
|
|
|
|
|
2008-10-16 13:01:15 +00:00
|
|
|
#if defined(CONFIG_SYS_MAMR_10COL)
|
2004-01-24 20:25:54 +00:00
|
|
|
/*
|
|
|
|
* try 10 column mode
|
|
|
|
*/
|
2008-10-16 13:01:15 +00:00
|
|
|
size10 = dram_size (CONFIG_SYS_MAMR_10COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
|
2004-01-24 20:25:54 +00:00
|
|
|
debug ("SDRAM Bank 0 in 10 column mode: %ld MB\n", size10 >> 20);
|
|
|
|
#else
|
|
|
|
size10 = 0;
|
2008-10-16 13:01:15 +00:00
|
|
|
#endif /* CONFIG_SYS_MAMR_10COL */
|
2004-01-24 20:25:54 +00:00
|
|
|
|
|
|
|
if ((size8 < size10) && (size9 < size10)) {
|
|
|
|
size_b0 = size10;
|
|
|
|
} else if ((size8 < size9) && (size10 < size9)) {
|
2002-08-26 22:36:39 +00:00
|
|
|
size_b0 = size9;
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_mamr = CONFIG_SYS_MAMR_9COL;
|
2004-01-24 20:25:54 +00:00
|
|
|
udelay (500);
|
|
|
|
} else {
|
2002-08-26 22:36:39 +00:00
|
|
|
size_b0 = size8;
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
|
2002-08-26 22:36:39 +00:00
|
|
|
udelay (500);
|
|
|
|
}
|
2004-01-02 14:00:00 +00:00
|
|
|
debug ("SDRAM Bank 0: %ld MB\n", size_b0 >> 20);
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
#ifndef CONFIG_CAN_DRIVER
|
2004-01-02 14:00:00 +00:00
|
|
|
if ((board_type != 'L') &&
|
2006-07-12 13:26:01 +00:00
|
|
|
(board_type != 'M') &&
|
2007-09-26 15:55:56 +00:00
|
|
|
(board_type != 'D') ) { /* only one SDRAM bank on L, M and D modules */
|
2002-08-26 22:36:39 +00:00
|
|
|
/*
|
|
|
|
* Check Bank 1 Memory Size
|
|
|
|
* use current column settings
|
|
|
|
* [9 column SDRAM may also be used in 8 column mode,
|
|
|
|
* but then only half the real size will be used.]
|
|
|
|
*/
|
2005-10-13 14:45:02 +00:00
|
|
|
size_b1 = dram_size (memctl->memc_mamr, (long int *)SDRAM_BASE3_PRELIM,
|
2004-01-02 14:00:00 +00:00
|
|
|
SDRAM_MAX_SIZE);
|
|
|
|
debug ("SDRAM Bank 1: %ld MB\n", size_b1 >> 20);
|
2002-08-26 22:36:39 +00:00
|
|
|
} else {
|
|
|
|
size_b1 = 0;
|
|
|
|
}
|
2004-01-02 14:00:00 +00:00
|
|
|
#endif /* CONFIG_CAN_DRIVER */
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
udelay (1000);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Adjust refresh rate depending on SDRAM type, both banks
|
|
|
|
* For types > 128 MBit leave it at the current (fast) rate
|
|
|
|
*/
|
|
|
|
if ((size_b0 < 0x02000000) && (size_b1 < 0x02000000)) {
|
|
|
|
/* reduce to 15.6 us (62.4 us / quad) */
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
|
2002-08-26 22:36:39 +00:00
|
|
|
udelay (1000);
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Final mapping: map bigger bank first
|
|
|
|
*/
|
|
|
|
if (size_b1 > size_b0) { /* SDRAM Bank 1 is bigger - map first */
|
|
|
|
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_or3 = ((-size_b1) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
|
|
|
|
memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
if (size_b0 > 0) {
|
|
|
|
/*
|
|
|
|
* Position Bank 0 immediately above Bank 1
|
|
|
|
*/
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_or2 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
|
|
|
|
memctl->memc_br2 = ((CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V)
|
2004-01-24 20:25:54 +00:00
|
|
|
+ size_b1;
|
2002-08-26 22:36:39 +00:00
|
|
|
} else {
|
|
|
|
unsigned long reg;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* No bank 0
|
|
|
|
*
|
|
|
|
* invalidate bank
|
|
|
|
*/
|
|
|
|
memctl->memc_br2 = 0;
|
|
|
|
|
|
|
|
/* adjust refresh rate depending on SDRAM type, one bank */
|
|
|
|
reg = memctl->memc_mptpr;
|
2008-10-16 13:01:15 +00:00
|
|
|
reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_mptpr = reg;
|
|
|
|
}
|
|
|
|
|
|
|
|
} else { /* SDRAM Bank 0 is bigger - map first */
|
|
|
|
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_or2 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_br2 =
|
2008-10-16 13:01:15 +00:00
|
|
|
(CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
if (size_b1 > 0) {
|
|
|
|
/*
|
|
|
|
* Position Bank 1 immediately above Bank 0
|
|
|
|
*/
|
|
|
|
memctl->memc_or3 =
|
2008-10-16 13:01:15 +00:00
|
|
|
((-size_b1) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_br3 =
|
2008-10-16 13:01:15 +00:00
|
|
|
((CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V)
|
2002-08-26 22:36:39 +00:00
|
|
|
+ size_b0;
|
|
|
|
} else {
|
|
|
|
unsigned long reg;
|
|
|
|
|
|
|
|
#ifndef CONFIG_CAN_DRIVER
|
|
|
|
/*
|
|
|
|
* No bank 1
|
|
|
|
*
|
|
|
|
* invalidate bank
|
|
|
|
*/
|
|
|
|
memctl->memc_br3 = 0;
|
|
|
|
#endif /* CONFIG_CAN_DRIVER */
|
|
|
|
|
|
|
|
/* adjust refresh rate depending on SDRAM type, one bank */
|
|
|
|
reg = memctl->memc_mptpr;
|
2008-10-16 13:01:15 +00:00
|
|
|
reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_mptpr = reg;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
udelay (10000);
|
|
|
|
|
|
|
|
#ifdef CONFIG_CAN_DRIVER
|
2007-09-26 15:55:54 +00:00
|
|
|
/* UPM initialization for CAN @ CLKOUT <= 66 MHz */
|
|
|
|
|
2002-08-26 22:36:39 +00:00
|
|
|
/* Initialize OR3 / BR3 */
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_or3 = CONFIG_SYS_OR3_CAN;
|
|
|
|
memctl->memc_br3 = CONFIG_SYS_BR3_CAN;
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
/* Initialize MBMR */
|
2003-11-25 16:55:19 +00:00
|
|
|
memctl->memc_mbmr = MBMR_GPL_B4DIS; /* GPL_B4 ouput line Disable */
|
2002-08-26 22:36:39 +00:00
|
|
|
|
|
|
|
/* Initialize UPMB for CAN: single read */
|
2007-09-26 15:55:54 +00:00
|
|
|
memctl->memc_mdr = 0xFFFFCC04;
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_mcr = 0x0100 | UPMB;
|
|
|
|
|
|
|
|
memctl->memc_mdr = 0x0FFFD004;
|
|
|
|
memctl->memc_mcr = 0x0101 | UPMB;
|
|
|
|
|
|
|
|
memctl->memc_mdr = 0x0FFFC000;
|
|
|
|
memctl->memc_mcr = 0x0102 | UPMB;
|
|
|
|
|
|
|
|
memctl->memc_mdr = 0x3FFFC004;
|
|
|
|
memctl->memc_mcr = 0x0103 | UPMB;
|
|
|
|
|
2007-09-26 15:55:54 +00:00
|
|
|
memctl->memc_mdr = 0xFFFFDC07;
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_mcr = 0x0104 | UPMB;
|
|
|
|
|
|
|
|
/* Initialize UPMB for CAN: single write */
|
2007-09-26 15:55:54 +00:00
|
|
|
memctl->memc_mdr = 0xFFFCCC04;
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_mcr = 0x0118 | UPMB;
|
|
|
|
|
2007-09-26 15:55:54 +00:00
|
|
|
memctl->memc_mdr = 0xCFFCDC04;
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_mcr = 0x0119 | UPMB;
|
|
|
|
|
2007-09-26 15:55:54 +00:00
|
|
|
memctl->memc_mdr = 0x3FFCC000;
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_mcr = 0x011A | UPMB;
|
|
|
|
|
2007-09-26 15:55:54 +00:00
|
|
|
memctl->memc_mdr = 0xFFFCC004;
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_mcr = 0x011B | UPMB;
|
|
|
|
|
2007-09-26 15:55:54 +00:00
|
|
|
memctl->memc_mdr = 0xFFFDC405;
|
2002-08-26 22:36:39 +00:00
|
|
|
memctl->memc_mcr = 0x011C | UPMB;
|
|
|
|
#endif /* CONFIG_CAN_DRIVER */
|
|
|
|
|
2003-08-05 17:43:17 +00:00
|
|
|
#ifdef CONFIG_ISP1362_USB
|
|
|
|
/* Initialize OR5 / BR5 */
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_or5 = CONFIG_SYS_OR5_ISP1362;
|
|
|
|
memctl->memc_br5 = CONFIG_SYS_BR5_ISP1362;
|
2003-08-05 17:43:17 +00:00
|
|
|
#endif /* CONFIG_ISP1362_USB */
|
2002-08-26 22:36:39 +00:00
|
|
|
return (size_b0 + size_b1);
|
|
|
|
}
|
|
|
|
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Check memory range for valid RAM. A simple memory test determines
|
|
|
|
* the actually available RAM size between addresses `base' and
|
|
|
|
* `base + maxsize'. Some (not all) hardware errors are detected:
|
|
|
|
* - short between address lines
|
|
|
|
* - short between data lines
|
|
|
|
*/
|
|
|
|
|
2004-01-02 14:00:00 +00:00
|
|
|
static long int dram_size (long int mamr_value, long int *base, long int maxsize)
|
2002-08-26 22:36:39 +00:00
|
|
|
{
|
2008-10-16 13:01:15 +00:00
|
|
|
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
|
2002-08-26 22:36:39 +00:00
|
|
|
volatile memctl8xx_t *memctl = &immap->im_memctl;
|
|
|
|
|
|
|
|
memctl->memc_mamr = mamr_value;
|
|
|
|
|
2004-01-06 22:38:14 +00:00
|
|
|
return (get_ram_size(base, maxsize));
|
2002-08-26 22:36:39 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
/* ------------------------------------------------------------------------- */
|
2004-01-16 00:30:56 +00:00
|
|
|
|
2008-09-16 16:02:19 +00:00
|
|
|
#ifdef CONFIG_MISC_INIT_R
|
2009-02-12 01:09:52 +00:00
|
|
|
extern void load_sernum_ethaddr(void);
|
2004-01-16 00:30:56 +00:00
|
|
|
int misc_init_r (void)
|
|
|
|
{
|
2008-10-16 13:01:15 +00:00
|
|
|
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
|
2008-09-16 16:02:19 +00:00
|
|
|
volatile memctl8xx_t *memctl = &immap->im_memctl;
|
|
|
|
|
2009-02-12 01:09:52 +00:00
|
|
|
load_sernum_ethaddr();
|
|
|
|
|
2008-10-16 13:01:15 +00:00
|
|
|
#ifdef CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ
|
2008-09-16 16:02:19 +00:00
|
|
|
int scy, trlx, flash_or_timing, clk_diff;
|
|
|
|
|
2008-10-16 13:01:15 +00:00
|
|
|
scy = (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & OR_SCY_MSK) >> 4;
|
|
|
|
if (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & OR_TRLX) {
|
2008-09-16 16:02:19 +00:00
|
|
|
trlx = OR_TRLX;
|
|
|
|
scy *= 2;
|
2008-09-17 08:17:55 +00:00
|
|
|
} else {
|
2008-09-16 16:02:19 +00:00
|
|
|
trlx = 0;
|
2008-09-17 08:17:55 +00:00
|
|
|
}
|
2008-09-16 16:02:19 +00:00
|
|
|
|
2008-09-17 08:17:55 +00:00
|
|
|
/*
|
|
|
|
* We assume that each 10MHz of bus clock require 1-clk SCY
|
|
|
|
* adjustment.
|
|
|
|
*/
|
2008-09-16 16:02:19 +00:00
|
|
|
clk_diff = (gd->bus_clk / 1000000) - 50;
|
|
|
|
|
2008-09-17 08:17:55 +00:00
|
|
|
/*
|
|
|
|
* We need proper rounding here. This is what the "+5" and "-5"
|
|
|
|
* are here for.
|
|
|
|
*/
|
2008-09-16 16:02:19 +00:00
|
|
|
if (clk_diff >= 0)
|
|
|
|
scy += (clk_diff + 5) / 10;
|
|
|
|
else
|
|
|
|
scy += (clk_diff - 5) / 10;
|
|
|
|
|
2008-09-17 08:17:55 +00:00
|
|
|
/*
|
|
|
|
* For bus frequencies above 50MHz, we want to use relaxed timing
|
|
|
|
* (OR_TRLX).
|
|
|
|
*/
|
2008-09-16 16:02:19 +00:00
|
|
|
if (gd->bus_clk >= 50000000)
|
|
|
|
trlx = OR_TRLX;
|
|
|
|
else
|
|
|
|
trlx = 0;
|
|
|
|
|
|
|
|
if (trlx)
|
|
|
|
scy /= 2;
|
|
|
|
|
|
|
|
if (scy > 0xf)
|
|
|
|
scy = 0xf;
|
|
|
|
if (scy < 1)
|
|
|
|
scy = 1;
|
|
|
|
|
|
|
|
flash_or_timing = (scy << 4) | trlx |
|
2008-10-16 13:01:15 +00:00
|
|
|
(CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & ~(OR_TRLX | OR_SCY_MSK));
|
2008-09-16 16:02:19 +00:00
|
|
|
|
2008-09-17 08:17:55 +00:00
|
|
|
memctl->memc_or0 =
|
|
|
|
flash_or_timing | (-flash_info[0].size & OR_AM_MSK);
|
2008-09-16 16:02:19 +00:00
|
|
|
#else
|
2008-09-17 08:17:55 +00:00
|
|
|
memctl->memc_or0 =
|
2008-10-16 13:01:15 +00:00
|
|
|
CONFIG_SYS_OR_TIMING_FLASH | (-flash_info[0].size & OR_AM_MSK);
|
2008-09-16 16:02:19 +00:00
|
|
|
#endif
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_MS_GPCM | BR_V;
|
2008-09-16 16:02:19 +00:00
|
|
|
|
|
|
|
debug ("## BR0: 0x%08x OR0: 0x%08x\n",
|
2008-09-17 08:17:55 +00:00
|
|
|
memctl->memc_br0, memctl->memc_or0);
|
2004-01-16 00:30:56 +00:00
|
|
|
|
2008-09-16 16:02:19 +00:00
|
|
|
if (flash_info[1].size) {
|
2008-10-16 13:01:15 +00:00
|
|
|
#ifdef CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ
|
2008-09-16 16:02:19 +00:00
|
|
|
memctl->memc_or1 = flash_or_timing |
|
2008-09-17 08:17:55 +00:00
|
|
|
(-flash_info[1].size & 0xFFFF8000);
|
2008-09-16 16:02:19 +00:00
|
|
|
#else
|
2008-10-16 13:01:15 +00:00
|
|
|
memctl->memc_or1 = CONFIG_SYS_OR_TIMING_FLASH |
|
2008-09-17 08:17:55 +00:00
|
|
|
(-flash_info[1].size & 0xFFFF8000);
|
2008-09-16 16:02:19 +00:00
|
|
|
#endif
|
2008-09-17 08:17:55 +00:00
|
|
|
memctl->memc_br1 =
|
2008-10-16 13:01:15 +00:00
|
|
|
((CONFIG_SYS_FLASH_BASE +
|
2008-09-17 08:17:55 +00:00
|
|
|
flash_info[0].
|
|
|
|
size) & BR_BA_MSK) | BR_MS_GPCM | BR_V;
|
2008-09-16 16:02:19 +00:00
|
|
|
|
|
|
|
debug ("## BR1: 0x%08x OR1: 0x%08x\n",
|
2008-09-17 08:17:55 +00:00
|
|
|
memctl->memc_br1, memctl->memc_or1);
|
2008-09-16 16:02:19 +00:00
|
|
|
} else {
|
2008-09-17 08:17:55 +00:00
|
|
|
memctl->memc_br1 = 0; /* invalidate bank */
|
2008-09-16 16:02:19 +00:00
|
|
|
|
|
|
|
debug ("## DISABLE BR1: 0x%08x OR1: 0x%08x\n",
|
2008-09-17 08:17:55 +00:00
|
|
|
memctl->memc_br1, memctl->memc_or1);
|
2008-09-16 16:02:19 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
# ifdef CONFIG_IDE_LED
|
2004-01-16 00:30:56 +00:00
|
|
|
/* Configure PA15 as output port */
|
|
|
|
immap->im_ioport.iop_padir |= 0x0001;
|
|
|
|
immap->im_ioport.iop_paodr |= 0x0001;
|
|
|
|
immap->im_ioport.iop_papar &= ~0x0001;
|
|
|
|
immap->im_ioport.iop_padat &= ~0x0001; /* turn it off */
|
2004-08-01 13:09:47 +00:00
|
|
|
# endif
|
2008-09-16 16:02:19 +00:00
|
|
|
|
2004-01-16 00:30:56 +00:00
|
|
|
return (0);
|
|
|
|
}
|
2008-09-16 16:02:19 +00:00
|
|
|
#endif /* CONFIG_MISC_INIT_R */
|
|
|
|
|
2004-01-16 00:30:56 +00:00
|
|
|
|
2004-08-01 13:09:47 +00:00
|
|
|
# ifdef CONFIG_IDE_LED
|
2004-01-16 00:30:56 +00:00
|
|
|
void ide_led (uchar led, uchar status)
|
|
|
|
{
|
2008-10-16 13:01:15 +00:00
|
|
|
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
|
2004-01-16 00:30:56 +00:00
|
|
|
|
|
|
|
/* We have one led for both pcmcia slots */
|
|
|
|
if (status) { /* led on */
|
|
|
|
immap->im_ioport.iop_padat |= 0x0001;
|
|
|
|
} else {
|
|
|
|
immap->im_ioport.iop_padat &= ~0x0001;
|
|
|
|
}
|
|
|
|
}
|
2004-08-01 13:09:47 +00:00
|
|
|
# endif
|
2004-01-16 00:30:56 +00:00
|
|
|
|
2008-09-01 14:21:22 +00:00
|
|
|
#ifdef CONFIG_LCD_INFO
|
|
|
|
#include <lcd.h>
|
2008-11-03 14:30:34 +00:00
|
|
|
#include <version.h>
|
2008-11-03 15:30:59 +00:00
|
|
|
#include <timestamp.h>
|
2008-09-01 14:21:22 +00:00
|
|
|
|
|
|
|
void lcd_show_board_info(void)
|
|
|
|
{
|
2008-11-03 14:30:34 +00:00
|
|
|
char temp[32];
|
|
|
|
|
2008-11-03 15:30:59 +00:00
|
|
|
lcd_printf ("%s (%s - %s)\n", U_BOOT_VERSION, U_BOOT_DATE, U_BOOT_TIME);
|
2008-09-01 14:21:22 +00:00
|
|
|
lcd_printf ("(C) 2008 DENX Software Engineering GmbH\n");
|
|
|
|
lcd_printf (" Wolfgang DENK, wd@denx.de\n");
|
|
|
|
#ifdef CONFIG_LCD_INFO_BELOW_LOGO
|
|
|
|
lcd_printf ("MPC823 CPU at %s MHz\n",
|
|
|
|
strmhz(temp, gd->cpu_clk));
|
|
|
|
lcd_printf (" %ld MB RAM, %ld MB Flash\n",
|
|
|
|
gd->ram_size >> 20,
|
|
|
|
gd->bd->bi_flashsize >> 20 );
|
|
|
|
#else
|
|
|
|
/* leave one blank line */
|
|
|
|
lcd_printf ("\nMPC823 CPU at %s MHz, %ld MB RAM, %ld MB Flash\n",
|
|
|
|
strmhz(temp, gd->cpu_clk),
|
|
|
|
gd->ram_size >> 20,
|
|
|
|
gd->bd->bi_flashsize >> 20 );
|
|
|
|
#endif /* CONFIG_LCD_INFO_BELOW_LOGO */
|
|
|
|
}
|
|
|
|
#endif /* CONFIG_LCD_INFO */
|
|
|
|
|
2010-02-09 14:50:21 +00:00
|
|
|
/*
|
|
|
|
* Device Tree Support
|
|
|
|
*/
|
|
|
|
#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
|
|
|
|
int fdt_set_node_and_value (void *blob,
|
|
|
|
char *nodename,
|
|
|
|
char *regname,
|
|
|
|
void *var,
|
|
|
|
int size)
|
|
|
|
{
|
|
|
|
int ret = 0;
|
|
|
|
int nodeoffset = 0;
|
|
|
|
|
|
|
|
nodeoffset = fdt_path_offset (blob, nodename);
|
|
|
|
if (nodeoffset >= 0) {
|
|
|
|
ret = fdt_setprop (blob, nodeoffset, regname, var,
|
|
|
|
size);
|
|
|
|
if (ret < 0) {
|
|
|
|
printf("ft_blob_update(): "
|
|
|
|
"cannot set %s/%s property; err: %s\n",
|
|
|
|
nodename, regname, fdt_strerror (ret));
|
|
|
|
}
|
|
|
|
} else {
|
|
|
|
printf("ft_blob_update(): "
|
|
|
|
"cannot find %s node err:%s\n",
|
|
|
|
nodename, fdt_strerror (nodeoffset));
|
|
|
|
}
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
int fdt_del_node_name (void *blob, char *nodename)
|
|
|
|
{
|
|
|
|
int ret = 0;
|
|
|
|
int nodeoffset = 0;
|
|
|
|
|
|
|
|
nodeoffset = fdt_path_offset (blob, nodename);
|
|
|
|
if (nodeoffset >= 0) {
|
|
|
|
ret = fdt_del_node (blob, nodeoffset);
|
|
|
|
if (ret < 0) {
|
|
|
|
printf("%s: cannot delete %s; err: %s\n",
|
|
|
|
__func__, nodename, fdt_strerror (ret));
|
|
|
|
}
|
|
|
|
} else {
|
|
|
|
printf("%s: cannot find %s node err:%s\n",
|
|
|
|
__func__, nodename, fdt_strerror (nodeoffset));
|
|
|
|
}
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
int fdt_del_prop_name (void *blob, char *nodename, char *propname)
|
|
|
|
{
|
|
|
|
int ret = 0;
|
|
|
|
int nodeoffset = 0;
|
|
|
|
|
|
|
|
nodeoffset = fdt_path_offset (blob, nodename);
|
|
|
|
if (nodeoffset >= 0) {
|
|
|
|
ret = fdt_delprop (blob, nodeoffset, propname);
|
|
|
|
if (ret < 0) {
|
|
|
|
printf("%s: cannot delete %s %s; err: %s\n",
|
|
|
|
__func__, nodename, propname,
|
|
|
|
fdt_strerror (ret));
|
|
|
|
}
|
|
|
|
} else {
|
|
|
|
printf("%s: cannot find %s node err:%s\n",
|
|
|
|
__func__, nodename, fdt_strerror (nodeoffset));
|
|
|
|
}
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* update "brg" property in the blob
|
|
|
|
*/
|
|
|
|
void ft_blob_update (void *blob, bd_t *bd)
|
|
|
|
{
|
|
|
|
uchar enetaddr[6];
|
|
|
|
ulong brg_data = 0;
|
|
|
|
|
|
|
|
/* BRG */
|
|
|
|
brg_data = cpu_to_be32(bd->bi_busfreq);
|
|
|
|
fdt_set_node_and_value(blob,
|
|
|
|
"/soc/cpm", "brg-frequency",
|
|
|
|
&brg_data, sizeof(brg_data));
|
|
|
|
|
|
|
|
/* MAC addr */
|
|
|
|
if (eth_getenv_enetaddr("ethaddr", enetaddr)) {
|
|
|
|
fdt_set_node_and_value(blob,
|
|
|
|
"ethernet0", "local-mac-address",
|
|
|
|
enetaddr, sizeof(u8) * 6);
|
|
|
|
}
|
|
|
|
|
|
|
|
if (hwconfig_arg_cmp("fec", "off")) {
|
|
|
|
/* no FEC on this plattform, delete DTS nodes */
|
|
|
|
fdt_del_node_name (blob, "ethernet1");
|
|
|
|
fdt_del_node_name (blob, "mdio1");
|
|
|
|
/* also the aliases entries */
|
|
|
|
fdt_del_prop_name (blob, "/aliases", "ethernet1");
|
|
|
|
fdt_del_prop_name (blob, "/aliases", "mdio1");
|
|
|
|
} else {
|
|
|
|
/* adjust local-mac-address for FEC ethernet */
|
|
|
|
if (eth_getenv_enetaddr("eth1addr", enetaddr)) {
|
|
|
|
fdt_set_node_and_value(blob,
|
|
|
|
"ethernet1", "local-mac-address",
|
|
|
|
enetaddr, sizeof(u8) * 6);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
2014-10-24 00:58:47 +00:00
|
|
|
int ft_board_setup(void *blob, bd_t *bd)
|
2010-02-09 14:50:21 +00:00
|
|
|
{
|
|
|
|
ft_cpu_setup(blob, bd);
|
|
|
|
ft_blob_update(blob, bd);
|
2014-10-24 00:58:47 +00:00
|
|
|
|
|
|
|
return 0;
|
2010-02-09 14:50:21 +00:00
|
|
|
}
|
|
|
|
#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
|