Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-20 10:13:09 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/configs/mx6ull_14x14_evk_defconfig

62 lines
1.3 KiB
Text
Raw Normal View History

arm: imx: add i.MX6ULL 14x14 EVK board support Add i.MX6ULL EVK board support: Add device tree file, which is copied from NXP Linux. Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR. The uart iomux settings are still keeped in board file. Boot Log: U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800) CPU: Freescale i.MX6ULL rev1.0 at 396MHz CPU: Commercial temperature grade (0C to 95C) at 15C Reset cause: POR Model: Freescale i.MX6 ULL 14x14 EVK Board Board: MX6ULL 14x14 EVK DRAM: 512 MiB MMC: initialized IMX pinctrl driver FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 => mmc dev 1 switch to partitions #0, OK mmc1 is current device Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-08-11 06:02:57 +00:00
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
configs: Migrate CONFIG_SYS_TEXT_BASE On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-03 17:10:38 +00:00
CONFIG_SYS_TEXT_BASE=0x87800000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-10 19:31:07 +00:00
CONFIG_NR_DRAM_BANKS=1
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-11-30 17:50:32 +00:00
CONFIG_SYS_MEMTEST_START=0x80000000
CONFIG_SYS_MEMTEST_END=0x88000000
env: Finish migration of common ENV options - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-19 01:02:10 +00:00
CONFIG_ENV_SIZE=0x2000
CONFIG_ENV_OFFSET=0xC0000
arm: mx6: Make all i.MX6 SoCs user-selectable We have a number of platforms that are a combination of a carrier board and System-on-Module (SoM) that in turn allows for the board to have different SoCs on it. In some cases, this is handled via board-specific Kconfig options. In other cases we make use of CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid configurations as we will not in turn get options that in Kconfig are selected by or depend on that setting. To resolve this, make the SoC option a choice in Kconfig and make boards depend on what they can support. This change opens us up for further clean-ups in the cases where a single CONFIG_TARGET_xxx can support different SoCs and today they do not, or do not cleanly do so. Reported-by: Matt Porter <mporter@konsulko.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> Cc: Soeren Moch <smoch@web.de> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Heiko Schocher <hs@denx.de> Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de> Cc: Ludwig Zenz <lzenz@dh-electronics.de> Cc: Lukasz Majewski <lukma@denx.de> Cc: Akshay Bhat <akshaybhat@timesys.com> Cc: Ken Lin <Ken.Lin@advantech.com.tw> Cc: Ian Ray <ian.ray@ge.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Cc: Simone CIANNI <simone.cianni@bticino.it> Cc: Adam Ford <aford173@gmail.com> Cc: Marcin Niestroj <m.niestroj@grinn-global.com> Cc: "Eric Bénard" <eric@eukrea.com> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Jason Liu <jason.hui.liu@nxp.com> Cc: Ye Li <ye.li@nxp.com> Cc: Eric Nelson <eric@nelint.com> Cc: Troy Kisky <troy.kisky@boundarydevices.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Parthiban Nallathambi <parthiban@linumiz.com> Cc: Marek Vasut <marex@denx.de> Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com> Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Niel Fourie <lusus@denx.de> Cc: Martyn Welch <martyn.welch@collabora.com> Cc: Richard Hu <richard.hu@technexion.com> Cc: Stefan Roese <sr@denx.de> Cc: Boris Brezillon <bbrezillon@kernel.org> Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com> Cc: Breno Lima <breno.lima@nxp.com> Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org> Cc: Silvio Fricke <open-source@softing.de> Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6] Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
2020-08-18 11:43:50 +00:00
CONFIG_MX6ULL=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 20:15:47 +00:00
CONFIG_TARGET_MX6ULL_14X14_EVK=y
Convert CONFIG_SYS_MALLOC_LEN to Kconfig This converts the following to Kconfig: CONFIG_SYS_MALLOC_LEN Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-08-29 01:34:49 +00:00
CONFIG_SYS_MALLOC_LEN=0x1000000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 18:38:00 +00:00
CONFIG_DM_GPIO=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28 12:46:52 +00:00
CONFIG_DEFAULT_DEVICE_TREE="imx6ull-14x14-evk"
Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-06 13:58:59 +00:00
CONFIG_SUPPORT_RAW_INITRD=y
Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-23 20:31:20 +00:00
CONFIG_BOARD_EARLY_INIT_F=y
arm: imx: add i.MX6ULL 14x14 EVK board support Add i.MX6ULL EVK board support: Add device tree file, which is copied from NXP Linux. Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR. The uart iomux settings are still keeped in board file. Boot Log: U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800) CPU: Freescale i.MX6ULL rev1.0 at 396MHz CPU: Commercial temperature grade (0C to 95C) at 15C Reset cause: POR Model: Freescale i.MX6 ULL 14x14 EVK Board Board: MX6ULL 14x14 EVK DRAM: 512 MiB MMC: initialized IMX pinctrl driver FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 => mmc dev 1 switch to partitions #0, OK mmc1 is current device Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-08-11 06:02:57 +00:00
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_GPIO=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 23:58:53 +00:00
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
arm: imx: add i.MX6ULL 14x14 EVK board support Add i.MX6ULL EVK board support: Add device tree file, which is copied from NXP Linux. Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR. The uart iomux settings are still keeped in board file. Boot Log: U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800) CPU: Freescale i.MX6ULL rev1.0 at 396MHz CPU: Commercial temperature grade (0C to 95C) at 15C Reset cause: POR Model: Freescale i.MX6 ULL 14x14 EVK Board Board: MX6ULL 14x14 EVK DRAM: 512 MiB MMC: initialized IMX pinctrl driver FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 => mmc dev 1 switch to partitions #0, OK mmc1 is current device Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-08-11 06:02:57 +00:00
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_CONTROL=y
Convert CONFIG_ENV_OVERWRITE to Kconfig This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-03 11:48:56 +00:00
CONFIG_ENV_OVERWRITE=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-28 11:16:32 +00:00
CONFIG_ENV_IS_IN_MMC=y
env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-13 03:46:36 +00:00
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-24 21:14:47 +00:00
CONFIG_SYS_MMC_ENV_DEV=1
Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
2018-04-01 16:37:53 +00:00
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-09 16:22:06 +00:00
CONFIG_BOUNCE_BUFFER=y
arm: imx: add i.MX6ULL 14x14 EVK board support Add i.MX6ULL EVK board support: Add device tree file, which is copied from NXP Linux. Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR. The uart iomux settings are still keeped in board file. Boot Log: U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800) CPU: Freescale i.MX6ULL rev1.0 at 396MHz CPU: Commercial temperature grade (0C to 95C) at 15C Reset cause: POR Model: Freescale i.MX6 ULL 14x14 EVK Board Board: MX6ULL 14x14 EVK DRAM: 512 MiB MMC: initialized IMX pinctrl driver FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 => mmc dev 1 switch to partitions #0, OK mmc1 is current device Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-08-11 06:02:57 +00:00
CONFIG_DM_74X164=y
CONFIG_DM_I2C=y
Convert CONFIG_SYS_I2C_MXC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_I2C_MXC CONFIG_SYS_I2C_MXC_I2C1 CONFIG_SYS_I2C_MXC_I2C2 CONFIG_SYS_I2C_MXC_I2C3 CONFIG_SYS_I2C_MXC_I2C4 Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-19 03:12:33 +00:00
CONFIG_SYS_I2C_MXC=y
Convert CONFIG_FSL_USDHC to Kconfig This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-14 12:23:43 +00:00
CONFIG_FSL_USDHC=y
mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTD Like in Linux, just use CONFIG_MTD to compile the MTD stack. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-10-03 17:50:05 +00:00
CONFIG_MTD=y
imx: mx6ull-14x14-evk: enable DM QSPI driver To support QSPI DM driver - Add spi0 alias for qspi node. Which is used for bus number 0. - Modify the n25q256a@0 compatible property to "spi-flash". - Modify spi4 (gpio_spi) node to spi5 - Define DM SPI/QSPI related config to enable QSPI Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-01-03 00:52:03 +00:00
CONFIG_DM_SPI_FLASH=y
Convert CONFIG_SF_DEFAULT_* to Kconfig This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-27 14:20:36 +00:00
CONFIG_SF_DEFAULT_SPEED=40000000
imx: mx6ull-14x14-evk: enable DM QSPI driver To support QSPI DM driver - Add spi0 alias for qspi node. Which is used for bus number 0. - Modify the n25q256a@0 compatible property to "spi-flash". - Modify spi4 (gpio_spi) node to spi5 - Define DM SPI/QSPI related config to enable QSPI Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-01-03 00:52:03 +00:00
CONFIG_SPI_FLASH_STMICRO=y
mx6ullevk: Enable Ethernet support Add Ethernet support using DM_ETH. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-02-03 17:23:58 +00:00
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
CONFIG_DM_ETH=y
mx6ul(l)evk: Enable DM_ETH_PHY This fixes eth0 not initializing properly. Both eth0 and eth1 use the MDIO interface on eth1 to access their PHYs. However, without DM_ETH_PHY, eth0 still tries to use its own MDIO interface to access its phy. Before this patch, a boot log might contain lines like Net: Warning: ethernet@20b4000 using MAC address from ROM eth1: ethernet@20b4000 [PRIME]Could not get PHY for FEC0: addr 2 After this patch they now look like Net: Warning: ethernet@20b4000 using MAC address from ROM eth1: ethernet@20b4000 [PRIME]Get shared mii bus on ethernet@2188000 Warning: ethernet@2188000 using MAC address from ROM , eth0: ethernet@2188000 As an alternative to DM_ETH_PHY, FEC_MXC_SHARE_MDIO could also have been used to achieve the same effect. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-12-28 19:58:30 +00:00
CONFIG_DM_ETH_PHY=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 20:15:47 +00:00
CONFIG_FEC_MXC=y
mx6ullevk: Enable Ethernet support Add Ethernet support using DM_ETH. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-02-03 17:23:58 +00:00
CONFIG_MII=y
arm: imx: add i.MX6ULL 14x14 EVK board support Add i.MX6ULL EVK board support: Add device tree file, which is copied from NXP Linux. Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR. The uart iomux settings are still keeped in board file. Boot Log: U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800) CPU: Freescale i.MX6ULL rev1.0 at 396MHz CPU: Commercial temperature grade (0C to 95C) at 15C Reset cause: POR Model: Freescale i.MX6 ULL 14x14 EVK Board Board: MX6ULL 14x14 EVK DRAM: 512 MiB MMC: initialized IMX pinctrl driver FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 => mmc dev 1 switch to partitions #0, OK mmc1 is current device Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-08-11 06:02:57 +00:00
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_DM_REGULATOR=y
mx6ullevk: Enable Ethernet support Add Ethernet support using DM_ETH. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-02-03 17:23:58 +00:00
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
Convert CONFIG_MXC_UART to Kconfig This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2020-06-09 14:46:46 +00:00
CONFIG_MXC_UART=y
Convert CONFIG_SPI to Kconfig This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15 17:51:26 +00:00
CONFIG_SPI=y
arm: imx: add i.MX6ULL 14x14 EVK board support Add i.MX6ULL EVK board support: Add device tree file, which is copied from NXP Linux. Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR. The uart iomux settings are still keeped in board file. Boot Log: U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800) CPU: Freescale i.MX6ULL rev1.0 at 396MHz CPU: Commercial temperature grade (0C to 95C) at 15C Reset cause: POR Model: Freescale i.MX6 ULL 14x14 EVK Board Board: MX6ULL 14x14 EVK DRAM: 512 MiB MMC: initialized IMX pinctrl driver FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 => mmc dev 1 switch to partitions #0, OK mmc1 is current device Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-08-11 06:02:57 +00:00
CONFIG_DM_SPI=y
imx: mx6ull-14x14-evk: enable DM QSPI driver To support QSPI DM driver - Add spi0 alias for qspi node. Which is used for bus number 0. - Modify the n25q256a@0 compatible property to "spi-flash". - Modify spi4 (gpio_spi) node to spi5 - Define DM SPI/QSPI related config to enable QSPI Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-01-03 00:52:03 +00:00
CONFIG_FSL_QSPI=y
configs: migrate CONFIG_IMX_THERMAL to defconfigs Done via moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-30 01:22:03 +00:00
CONFIG_IMX_THERMAL=y
Reference in a new issue Copy permalink