u-boot/board/jse/jse.c

148 lines
4.5 KiB
C
Raw Normal View History

/*
* Copyright (c) 2004 Picture Elements, Inc.
* Stephen Williams (steve@icarus.com)
*
* SPDX-License-Identifier: GPL-2.0+
*/
# include <common.h>
# include <asm/ppc4xx.h>
# include <asm/processor.h>
# include <asm/io.h>
# include "jse_priv.h"
/*
* This function is run very early, out of flash, and before devices are
* initialized. It is called by arch/powerpc/lib/board.c:board_init_f by virtue
* of being in the init_sequence array.
*
* The SDRAM has been initialized already -- start.S:start called
* init.S:init_sdram early on -- but it is not yet being used for
* anything, not even stack. So be careful.
*/
int board_early_init_f (void)
{
/*-------------------------------------------------------------------------+
| Interrupt controller setup for the JSE board.
| Note: IRQ 0-15 405GP internally generated; active high; level sensitive
| IRQ 16 405GP internally generated; active low; level sensitive
| IRQ 17-24 RESERVED/UNUSED
| IRQ 25 (EXT IRQ 0) PCI SLOT 0; active low; level sensitive
| IRQ 26 (EXT IRQ 1) PCI SLOT 1; active low; level sensitive
| IRQ 27 (EXT IRQ 2) JP2C CHIP ; active low; level sensitive
| IRQ 28 (EXT IRQ 3) PCI bridge; active low; level sensitive
| IRQ 29 (EXT IRQ 4) SystemACE IRQ; active high
| IRQ 30 (EXT IRQ 5) SystemACE BRdy (unused)
| IRQ 31 (EXT IRQ 6) (unused)
+-------------------------------------------------------------------------*/
mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
mtdcr (UIC0ER, 0x00000000); /* disable all ints */
mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical */
mtdcr (UIC0PR, 0xFFFFFF87); /* set int polarities */
mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */
mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
/* Configure the interface to the SystemACE MCU port.
The SystemACE is fast, but there is no reason to have
excessivly tight timings. So the settings are slightly
generous. */
/* EBC0_B1AP: BME=1, TWT=2, CSN=0, OEN=1,
WBN=0, WBF=1, TH=0, RE=0, SOR=0, BEM=0, PEN=0 */
mtdcr (EBC0_CFGADDR, PB1AP);
mtdcr (EBC0_CFGDATA, 0x01011000);
/* EBC0_B1CR: BAS=x, BS=0(1MB), BU=3(R/W), BW=0(8bits) */
mtdcr (EBC0_CFGADDR, PB1CR);
mtdcr (EBC0_CFGDATA, CONFIG_SYS_SYSTEMACE_BASE | 0x00018000);
/* Enable the /PerWE output as /PerWE, instead of /PCIINT. */
/* CPC0_CR1 |= PCIPW */
mtdcr (0xb2, mfdcr (0xb2) | 0x00004000);
return 0;
}
#ifdef CONFIG_BOARD_PRE_INIT
int board_pre_init (void)
{
return board_early_init_f ();
}
#endif
/*
* This function is also called by arch/powerpc/lib/board.c:board_init_f (it is
* also in the init_sequence array) but later. Many more things are
* configured, but we are still running from flash.
*/
int checkboard (void)
{
unsigned vers, status;
/* check that the SystemACE chip is alive. */
printf ("ACE: ");
vers = readw (CONFIG_SYS_SYSTEMACE_BASE + 0x16);
printf ("SystemACE %u.%u (build %u)",
(vers >> 12) & 0x0f, (vers >> 8) & 0x0f, vers & 0xff);
status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04);
#ifdef DEBUG
printf (" STATUS=0x%08x", status);
#endif
/* If the flash card is present and there is an initial error,
then force a restart of the program. */
if (status & 0x00000010) {
printf (" CFDETECT");
if (status & 0x04) {
/* CONTROLREG = CFGPROG */
writew (0x1000, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
udelay (500);
/* CONTROLREG = CFGRESET */
writew (0x0080, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
udelay (500);
writew (0x0000, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
/* CONTROLREG = CFGSTART */
writew (0x0020, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04);
}
}
/* Wait for the SystemACE to program its chain of devices. */
while ((status & 0x84) == 0x00) {
udelay (500);
status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04);
}
if (status & 0x04)
printf (" CFG-ERROR");
if (status & 0x80)
printf (" CFGDONE");
printf ("\n");
/* Force /RTS to active. The board it not wired quite
correctly to use cts/rtc flow control, so just force the
/RST active and forget about it. */
writeb (readb (0xef600404) | 0x03, 0xef600404);
printf ("JSE: ready\n");
return 0;
}
/* **** No more functions called by board_init_f. **** */
/*
* This function is called by arch/powerpc/lib/board.c:board_init_r. At this
* point, basic setup is done, U-Boot has been moved into SDRAM and
* PCI has been set up. From here we done late setup.
*/
int misc_init_r (void)
{
host_bridge_init ();
return 0;
}