mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-24 21:54:01 +00:00
86 lines
2 KiB
Text
86 lines
2 KiB
Text
|
U-Boot for UniPhier SoC family
|
||
|
|
==============================
|
||
|
|
|
||
|
|
|
||
|
|
Tested toolchains
|
||
|
|
-----------------
|
||
|
|
|
||
|
|
(a) Ubuntu packages (CROSS_COMPILE=arm-linux-gnueabi-)
|
||
|
|
|
||
|
|
If you are building U-Boot on Ubuntu, its standard package is recommended.
|
||
|
|
You can install it as follows:
|
||
|
|
|
||
|
|
$ sudo apt-get install gcc-arm-linux-gnueabi-
|
||
|
|
|
||
|
|
(b) Linaro compilers (CROSS_COMPILE=arm-linux-gnueabihf-)
|
||
|
|
|
||
|
|
You can download pre-built toolchains from:
|
||
|
|
|
||
|
|
http://www.linaro.org/downloads/
|
||
|
|
|
||
|
|
(c) kernel.org compilers (CROSS_COMPILE=arm-unknown-linux-gnueabi-)
|
||
|
|
|
||
|
|
You can download pre-built toolchains from:
|
||
|
|
|
||
|
|
ftp://www.kernel.org/pub/tools/crosstool/files/bin/
|
||
|
|
|
||
|
|
|
||
|
|
Compile the source
|
||
|
|
------------------
|
||
|
|
|
||
|
|
PH1-Pro4:
|
||
|
|
$ make ph1_pro4_defconfig
|
||
|
|
$ make CROSS_COMPILE=arm-linux-gnueabi-
|
||
|
|
|
||
|
|
PH1-LD4:
|
||
|
|
$ make ph1_ld4_defconfig
|
||
|
|
$ make CROSS_COMPILE=arm-linux-gnueabi-
|
||
|
|
|
||
|
|
PH1-sLD8:
|
||
|
|
$ make ph1_sld8_defconfig
|
||
|
|
$ make CROSS_COMPILE=arm-linux-gnueabi-
|
||
|
|
|
||
|
|
You may wish to change the "CROSS_COMPILE=arm-linux-gnueabi-"
|
||
|
|
to use your favorite compiler.
|
||
|
|
|
||
|
|
|
||
|
|
Burn U-Boot images to NAND
|
||
|
|
--------------------------
|
||
|
|
|
||
|
|
Write two files to the NAND device as follows:
|
||
|
|
- spl/u-boot-spl.bin at the offset address 0x00000000
|
||
|
|
- u-boot-dtb.img at the offset address 0x00010000
|
||
|
|
|
||
|
|
If a TFTP server is available, the images can be easily updated.
|
||
|
|
Just copy the u-boot-spl.bin and u-boot-dtb.img to the TFTP public directory,
|
||
|
|
and then run the following command at the U-Boot command line:
|
||
|
|
|
||
|
|
=> run nandupdate
|
||
|
|
|
||
|
|
|
||
|
|
UniPhier specific commands
|
||
|
|
--------------------------
|
||
|
|
|
||
|
|
- pinmon (enabled by CONFIG_CMD_PINMON)
|
||
|
|
shows the boot mode pins that has been latched at the power-on reset
|
||
|
|
|
||
|
|
- ddrphy (enabled by CONFIG_CMD_DDRPHY_DUMP)
|
||
|
|
shows the DDR PHY parameters set by the PHY training
|
||
|
|
|
||
|
|
|
||
|
|
Supported devices
|
||
|
|
-----------------
|
||
|
|
|
||
|
|
- UART (on-chip)
|
||
|
|
- NAND
|
||
|
|
- USB (2.0)
|
||
|
|
- LAN (on-board SMSC9118)
|
||
|
|
- I2C
|
||
|
|
- EEPROM (connected to the on-board I2C bus)
|
||
|
|
- Support card (SRAM, NOR flash, some peripherals)
|
||
|
|
|
||
|
|
|
||
|
|
--
|
||
|
|
Masahiro Yamada <yamada.m@jp.panasonic.com>
|
||
|
|
Feb. 2015
|