u-boot/configs/Colombus_defconfig

CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_SPL=y
CONFIG_MACH_SUN6I=y
CONFIG_DRAM_CLK=240
CONFIG_DRAM_ZQ=251
CONFIG_USB1_VBUS_PIN=""
CONFIG_I2C0_ENABLE=y
CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:2048,y:1536,depth:24,pclk_khz:208000,le:5,ri:150,up:9,lo:24,hs:5,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH27"
CONFIG_VIDEO_LCD_BL_EN="PM1"
CONFIG_VIDEO_LCD_BL_PWM="PH13"
CONFIG_VIDEO_LCD_PANEL_I2C_SDA="PA23"
CONFIG_VIDEO_LCD_PANEL_I2C_SCL="PA24"
CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804=y
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-colombus"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_SPL_DOS_PARTITION is not set
# CONFIG_SPL_EFI_PARTITION is not set
CONFIG_ETH_DESIGNWARE=y
CONFIG_RGMII=y
CONFIG_SUN7I_GMAC=y
CONFIG_AXP_ALDO1_VOLT=3300
CONFIG_USB_EHCI_HCD=y
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
kconfig: remove meaningless prefixes in defconfig files Since commit e02ee2548afe (kconfig: switch to single .config configuration), the prefixes in defconfig files such as "+S:", "+ST:", etc., are meaningless. This commit was generated by the following command: find configs -name '_defconfig' \| xargs sed -i 's/^+ST://' Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> 2015-03-12 04:24:39 +00:00			`CONFIG_ARM=y`
			`CONFIG_ARCH_SUNXI=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2018-04-08 00:27:54 +00:00			`CONFIG_SPL=y`
kconfig: remove meaningless prefixes in defconfig files Since commit e02ee2548afe (kconfig: switch to single .config configuration), the prefixes in defconfig files such as "+S:", "+ST:", etc., are meaningless. This commit was generated by the following command: find configs -name '_defconfig' \| xargs sed -i 's/^+ST://' Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> 2015-03-12 04:24:39 +00:00			`CONFIG_MACH_SUN6I=y`
			`CONFIG_DRAM_CLK=240`
			`CONFIG_DRAM_ZQ=251`
			`CONFIG_USB1_VBUS_PIN=""`
sunxi: Display: Add support for eDP panels connected via an anx9804 bridge Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge, such as found on the Colombus devkit. While at it also fix the wrong indentation of the SSD2828 Kconfig help text in board/sunxi/Kconfig. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-08-08 14:13:53 +00:00			`CONFIG_I2C0_ENABLE=y`
			`CONFIG_AXP_GPIO=y`
			`CONFIG_VIDEO_LCD_MODE="x:2048,y:1536,depth:24,pclk_khz:208000,le:5,ri:150,up:9,lo:24,hs:5,vs:1,sync:3,vmode:0"`
			`CONFIG_VIDEO_LCD_DCLK_PHASE=0`
			`CONFIG_VIDEO_LCD_POWER="PH27"`
			`CONFIG_VIDEO_LCD_BL_EN="PM1"`
			`CONFIG_VIDEO_LCD_BL_PWM="PH13"`
			`CONFIG_VIDEO_LCD_PANEL_I2C_SDA="PA23"`
			`CONFIG_VIDEO_LCD_PANEL_I2C_SCL="PA24"`
			`CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804=y`
Clean all defconfigs with savedefconfig In order to reduce merge conflicts and to maintain the simplest possible defconfig files, we should be using the savedefconfig feature of Kconfig every time a new feature is added. This keeps the defconfig settings to a minimum (only those things not default) and keeps them in the same order as the Kconfig options. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: Tom Rini <trini@konsulko.com> 2015-05-12 19:46:24 +00:00			`CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-colombus"`
Move default y configs out of arch/board Kconfig Some archs/boards specify their own default by pre-defining the config which causes the Kconfig system to mix up the order of the configs in the defconfigs... This will cause merge pain if allowed to proliferate. Remove the configs that behave this way from the archs. A few configs still remain, but that is because they only exist as defaults and do not have a proper Kconfig entry. Those appear to be: SPIFLASH DISPLAY_BOARDINFO Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates, drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM] Signed-off-by: Tom Rini <trini@konsulko.com> 2015-06-22 21:15:29 +00:00			`# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set`
Move defaults from config_cmd_default.h to Kconfig This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com> 2015-06-22 21:15:30 +00:00			`# CONFIG_CMD_FLASH is not set`
disk: convert CONFIG_DOS_PARTITION to Kconfig Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com> 2017-01-27 10:00:37 +00:00			`# CONFIG_SPL_DOS_PARTITION is not set`
disk: convert CONFIG_EFI_PARTITION to Kconfig Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com> 2017-01-27 10:00:41 +00:00			`# CONFIG_SPL_EFI_PARTITION is not set`
Kconfig: Move CONFIG_DESIGNWARE_ETH to Kconfig Move this to Kconfig and clean up board config files that use it. Also rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists in drivers/net/Kconfig. Signed-off-by: Simon Glass <sjg@chromium.org> Version 1: Acked-by: Joe Hershberger <joe.hershberger@ni.com> 2015-04-05 22:07:34 +00:00			`CONFIG_ETH_DESIGNWARE=y`
sunxi: Convert CONFIG_RGMII to Kconfig Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to update defconfig files of SYS_EXTRA_OPTIONS accordingly and remove it when it is possible. Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> 2017-04-02 10:59:08 +00:00			`CONFIG_RGMII=y`
sunxi: Move SUNXI_GMAC to Kconfig Move the SUNXI_GMAC config option to Kconfig, remove it from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC. Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> 2017-04-02 10:59:03 +00:00			`CONFIG_SUN7I_GMAC=y`
sunxi: power: Make all voltages configurable through Kconfig On boards with axp221/223 pmic-s we already allow configuring most voltages. Make the Kconfig options for these also apply to boards with axp152 / axp209 pmic-s and extend them to configure all voltages. The Kconfig defaults are chosen so that this commit does not introduce any functional changes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-09-30 13:22:42 +00:00			`CONFIG_AXP_ALDO1_VOLT=3300`
sunxi: Update selects in arch/arm/Kconfig for DM conversions With certain features being convert to DM now we want sunxi to default to having DM enabled for ETH/SERIAL and USB in some cases. Cc: Hans de Goede <hdegoede@redhat.com> Cc: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Tom Rini <trini@konsulko.com> [hdegoede@redhat.com: Also select CONFIG_USB for all sunxi builds] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Simon Glass <sjg@chromium.org> 2015-06-30 20:51:15 +00:00			`CONFIG_USB_EHCI_HCD=y`
configs: Migrate all of the existing USB symbols, except fastboot This syncs all of the currently Kconfig'd symbols out of the headers and into the defconfig files. This has two exceptions, first am335x_evm needs to be converted to DM in SPL and then it can stop undef'ing CONFIG_DM_USB. Leaving this as-is results in a build failure, and without work, run time failure. The other case is am43xx_evm.h and in turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB host mode in SPL, but still desire to have gadget mode in U-Boot proper. Signed-off-by: Tom Rini <trini@konsulko.com> 2017-08-25 21:50:26 +00:00			`CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y`