u-boot/include/configs/pxm2.h

132 lines
3.1 KiB
C
Raw Normal View History

/*
* siemens pxm2
* (C) Copyright 2013 Siemens Schweiz AG
* (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* Based on:
* U-Boot file:/include/configs/am335x_evm.h
*
* Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_PXM2_H
#define __CONFIG_PXM2_H
#define CONFIG_SIEMENS_PXM2
#define CONFIG_SIEMENS_MACH_TYPE MACH_TYPE_PXM2
#include "siemens-am33x-common.h"
#define DDR_IOCTRL_VAL 0x18b
#define DDR_PLL_FREQ 266
#define BOARD_DFU_BUTTON_GPIO 59
#define BOARD_LCD_POWER 111
#define BOARD_BACK_LIGHT 112
#define BOARD_TOUCH_POWER 57
#define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \
"button_dfu0=59\0" \
"led0=117,0,1\0" \
/* Physical Memory Map */
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* 1GB */
/* I2C Configuration */
#define CONFIG_SYS_I2C_SPEED 400000
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_PHY_ATHEROS
#define CONFIG_FACTORYSET
#ifndef CONFIG_SPL_BUILD
/* Use common default */
/* Default env settings */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hostname=pxm2\0" \
"ubi_off=2048\0"\
"nand_img_size=0x500000\0" \
"optargs=\0" \
"preboot=draco_led 0\0" \
CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"splashpos=m,m\0" \
CONFIG_ENV_SETTINGS_V1 \
CONFIG_ENV_SETTINGS_NAND_V1 \
"mmc_dev=0\0" \
"mmc_root=/dev/mmcblk0p2 rw\0" \
"mmc_root_fs_type=ext4 rootwait\0" \
"mmc_load_uimage=" \
"mmc rescan; " \
"setenv bootfile uImage;" \
"fatload mmc ${mmc_dev} ${kloadaddr} ${bootfile}\0" \
"loadbootenv=fatload mmc ${mmc_dev} ${loadaddr} ${bootenv}\0" \
"importbootenv=echo Importing environment from mmc ...; " \
"env import -t $loadaddr $filesize\0" \
"mmc_args=run bootargs_defaults;" \
"mtdparts default;" \
"setenv bootargs ${bootargs} " \
"root=${mmc_root} ${mtdparts}" \
"rootfstype=${mmc_root_fs_type} ip=${ip_method} " \
"eth=${ethaddr} " \
"\0" \
"mmc_boot=run mmc_args; " \
"run mmc_load_uimage; " \
"bootm ${kloadaddr}\0" \
""
#ifndef CONFIG_RESTORE_FLASH
/* set to negative value for no autoboot */
#define CONFIG_BOOTCOMMAND \
"if dfubutton; then " \
"run dfu_start; " \
"reset; " \
"fi; " \
"if mmc rescan; then " \
"echo SD/MMC found on device ${mmc_dev};" \
"if run loadbootenv; then " \
"echo Loaded environment from ${bootenv};" \
"run importbootenv;" \
"fi;" \
"if test -n $uenvcmd; then " \
"echo Running uenvcmd ...;" \
"run uenvcmd;" \
"fi;" \
"if run mmc_load_uimage; then " \
"run mmc_args;" \
"bootm ${kloadaddr};" \
"fi;" \
"fi;" \
"run nand_boot;" \
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"reset;"
#else
#define CONFIG_BOOTCOMMAND \
"setenv autoload no; " \
"dhcp; " \
"if tftp 80000000 debrick.scr; then " \
"source 80000000; " \
"fi"
#endif
#endif /* CONFIG_SPL_BUILD */
#if defined(CONFIG_VIDEO)
#define CONFIG_VIDEO_DA8XX
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_BMP_LOGO
#define DA8XX_LCD_CNTL_BASE LCD_CNTL_BASE
#define PWM_TICKS 0x1388
#define PWM_DUTY 0x200
#endif
#endif /* ! __CONFIG_PXM2_H */