u-boot/drivers/mtd/spi/Makefile

19 lines
493 B
Makefile
Raw Normal View History

#
# (C) Copyright 2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# SPDX-License-Identifier: GPL-2.0+
#
obj-$(CONFIG_DM_SPI_FLASH) += sf-uclass.o
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_SPI_BOOT) += fsl_espi_spl.o
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
obj-$(CONFIG_SPL_SPI_SUNXI) += sunxi_spi_spl.o
endif
obj-$(CONFIG_SPI_FLASH) += sf_probe.o spi_flash.o spi_flash_ids.o sf.o
obj-$(CONFIG_SPI_FLASH_DATAFLASH) += sf_dataflash.o
mtd, spi: Add MTD layer driver Add MTD layer driver for spi, original patch from: http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493dd7089eaa51b9e639765cced Changes from Heiko Schocher against this patch: - Remove compile error if not defining CONFIG_SPI_FLASH_MTD: LD drivers/mtd/spi/built-in.o drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister': /home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister' drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister': /home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister' drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1 make: *** [drivers/mtd/spi] Fehler 2 - Add a README entry. - Add correct writebufsize, to fit with Linux v3.14 MTD, UBI/UBIFS sync. Note (From Jagan): For testing raw mtd parition erase/read/write operations using cmd_sf, sf_mtd should be required to register the spi flash device to MTD layer but the sf_mtd_info ops were not required until and unless if we use any flash filesystem layer say for example UBI. Due to this the foot-print got increased ~290bytes in non-UBI case here that should be acceptible. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Jagannadh Teki <jteki@openedev.com> Reviewed-by: Jagannadh Teki <jteki@openedev.com>
2015-04-27 05:42:04 +00:00
obj-$(CONFIG_SPI_FLASH_MTD) += sf_mtd.o
obj-$(CONFIG_SPI_FLASH_SANDBOX) += sandbox.o