u-boot/include/configs/siemens-am33x-common.h

465 lines
15 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* siemens am33x common board options
* (C) Copyright 2013 Siemens Schweiz AG
* (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* Based on:
* U-Boot file:/include/configs/am335x_evm.h
*
* Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
*/
#ifndef __CONFIG_SIEMENS_AM33X_COMMON_H
#define __CONFIG_SIEMENS_AM33X_COMMON_H
#include <asm/arch/omap.h>
#define CONFIG_DMA_COHERENT
#define CONFIG_DMA_COHERENT_SIZE (1 << 20)
#define CONFIG_SYS_MALLOC_LEN (16 * 1024 * 1024)
#ifdef CONFIG_SIEMENS_MACH_TYPE
#define CONFIG_MACH_TYPE CONFIG_SIEMENS_MACH_TYPE
#endif
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
/* commands to include */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_ROOTPATH "/opt/eldk"
#endif
#define CONFIG_ENV_OVERWRITE 1
#define CONFIG_SYS_AUTOLOAD "yes"
/* Clock Defines */
#define V_OSCK 24000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK)
/* We set the max number of command args high to avoid HUSH bugs. */
#define CONFIG_SYS_MAXARGS 32
/* Console I/O Buffer Size */
#define CONFIG_SYS_CBSIZE 1024
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/*
* memtest works on 8 MB in DRAM after skipping 32MB from
* start addr of ram disk
*/
#define CONFIG_SYS_MEMTEST_START (PHYS_DRAM_1 + (64 * 1024 * 1024))
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START \
+ (8 * 1024 * 1024))
#define CONFIG_SYS_LOAD_ADDR 0x81000000 /* Default load address */
/* Physical Memory Map */
#define PHYS_DRAM_1 0x80000000 /* DRAM Bank #1 */
#define CONFIG_SYS_SDRAM_BASE PHYS_DRAM_1
#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
GENERATED_GBL_DATA_SIZE)
/* Platform/Board specific defs */
#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
/* NS16550 Configuration */
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#endif
#define CONFIG_SYS_NS16550_CLK (48000000)
#define CONFIG_SYS_NS16550_COM1 0x44e09000
#define CONFIG_SYS_NS16550_COM4 0x481a6000
/* I2C Configuration */
#define CONFIG_I2C
#define CONFIG_SYS_I2C
/* Defines for SPL */
TI: Rework SRAM definitions and maximums On all TI platforms the ROM defines a "downloaded image" area at or near the start of SRAM which is followed by a reserved area. As it is at best bad form and at worst possibly harmful in corner cases to write in this reserved area, we stop doing that by adding in the define NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this. At current we define the end of scratch space at 0x228 bytes past the start of scratch space this this gives us a lot of room to grow. As these scratch uses are non-optional today, all targets are modified to respect this boundary. Tested on OMAP4 Pandaboard, OMAP3 Beagle xM Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Paul Kocialkowski <contact@paulk.fr> Cc: Enric Balletbo i Serra <eballetbo@gmail.com> Cc: Adam Ford <aford173@gmail.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Thomas Weber <weber@corscience.de> Cc: Hannes Schmelzer <oe5hpm@oevsv.at> Cc: Thomas Chou <thomas@wytron.com.tw> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Simon Glass <sjg@chromium.org> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Sam Protsenko <semen.protsenko@linaro.org> Cc: Heiko Schocher <hs@denx.de> Cc: Samuel Egli <samuel.egli@siemens.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Cc: Ben Whitten <ben.whitten@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: "B, Ravi" <ravibabu@ti.com> Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Ash Charles <ashcharles@gmail.com> Cc: "Kipisz, Steven" <s-kipisz2@ti.com> Cc: Daniel Allred <d-allred@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Ladislav Michl <ladis@linux-mips.org>
2016-08-26 17:30:43 +00:00
#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
CONFIG_SPL_TEXT_BASE)
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
CONFIG_SYS_NAND_PAGE_SIZE)
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12, 13, 14, 15, 16, 17, \
18, 19, 20, 21, 22, 23, 24, 25, \
26, 27, 28, 29, 30, 31, 32, 33, \
34, 35, 36, 37, 38, 39, 40, 41, \
42, 43, 44, 45, 46, 47, 48, 49, \
50, 51, 52, 53, 54, 55, 56, 57, }
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 14
mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed CONFIG_xx used for selecting NAND ecc-schemes. This patch aims at solving following issues. 1) Currently ecc-scheme is tied to SoC platform, which prevents user to select other ecc-schemes also supported in hardware. like; - most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW). - most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware supports BCH16 ecc-scheme also. 2) Different platforms use different CONFIG_xx to select ecc-schemes, which adds confusion for user while migrating platforms. - *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only 8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW) whereas ELM hardware engine supports other ecc-schemes also like; BCH4, and BCH16 (in future). - *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW). - *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency on SoC platform and NAND driver. And user can select ecc-scheme independently foreach board. However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand) Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-18 13:33:01 +00:00
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
#define CONFIG_SYS_NAND_ECCSTEPS 4
#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
CONFIG_SYS_NAND_ECCSTEPS)
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
/*
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
* 64 bytes before this address should be set aside for u-boot.img's
* header. That is 0x800FFFC0--0x80100000 should not be used for any
* other needs.
*/
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
/*
* Since SPL did pll and ddr initialization for us,
* we don't need to do it twice.
*/
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SKIP_LOWLEVEL_INIT
#endif
#ifndef CONFIG_SPL_BUILD
/*
* USB configuration
*/
#define CONFIG_AM335X_USB0
#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL
#define CONFIG_AM335X_USB1
#define CONFIG_AM335X_USB1_MODE MUSB_HOST
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
/* USB DRACO ID as default */
#define CONFIG_USBD_HS
/* USB Device Firmware Update support */
#define CONFIG_SYS_DFU_DATA_BUF_SIZE (1 << 20)
#define DFU_MANIFEST_POLL_TIMEOUT 25000
#endif /* CONFIG_SPL_BUILD */
/*
* Default to using SPI for environment, etc. We have multiple copies
* of SPL as the ROM will check these locations.
* 0x0 - 0x20000 : First copy of SPL
* 0x20000 - 0x40000 : Second copy of SPL
* 0x40000 - 0x60000 : Third copy of SPL
* 0x60000 - 0x80000 : Fourth copy of SPL
* 0x80000 - 0xDF000 : U-Boot
* 0xDF000 - 0xE0000 : U-Boot Environment
* 0xE0000 - 0x442000 : Linux Kernel
* 0x442000 - 0x800000 : Userland
*/
#define CONFIG_BOOTP_DEFAULT
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
/* NAND support */
#ifdef CONFIG_MTD_RAW_NAND
/* UBI Support */
/* Commen environment */
#define COMMON_ENV_DFU_ARGS "dfu_args=run bootargs_defaults;" \
"setenv bootargs ${bootargs};" \
"mtdparts default;" \
"draco_led 1;" \
"dfu 0 nand 0;" \
"draco_led 0;\0" \
#define COMMON_ENV_NAND_BOOT \
"nand_boot=echo Booting from nand; " \
"if test ${upgrade_available} -eq 1; then " \
"if test ${bootcount} -gt ${bootlimit}; " \
"then " \
"setenv upgrade_available 0;" \
"setenv ${partitionset_active} true;" \
"if test -n ${A}; then " \
"setenv partitionset_active B; " \
"env delete A; " \
"fi;" \
"if test -n ${B}; then " \
"setenv partitionset_active A; " \
"env delete B; " \
"fi;" \
"saveenv; " \
"fi;" \
"fi;" \
"echo set ${partitionset_active}...;" \
"run nand_args; "
#define COMMON_ENV_NAND_CMDS "flash_self=run nand_boot\0" \
"flash_self_test=setenv testargs test; " \
"run nand_boot\0" \
"dfu_start=echo Preparing for dfu mode ...; " \
"run dfu_args; \0"
#define COMMON_ENV_SETTINGS \
"verify=no \0" \
"project_dir=targetdir\0" \
"upgrade_available=0\0" \
"altbootcmd=run bootcmd\0" \
"partitionset_active=A\0" \
"loadaddr=0x82000000\0" \
"kloadaddr=0x81000000\0" \
"script_addr=0x81900000\0" \
"console=console=ttyMTD,mtdoops console=ttyO0,115200n8 panic=5\0" \
"nfsopts=nolock rw\0" \
"ip_method=none\0" \
"bootenv=uEnv.txt\0" \
"bootargs_defaults=setenv bootargs " \
"console=${console} " \
"${testargs} " \
"${optargs}\0" \
"siemens_help=echo; "\
"echo Type 'run flash_self' to use kernel and root " \
"filesystem on memory; echo Type 'run flash_self_test' to " \
"use kernel and root filesystem on memory, boot in test " \
"mode; echo Not ready yet: 'run flash_nfs' to use kernel " \
"from memory and root filesystem over NFS; echo Type " \
"'run net_nfs' to get Kernel over TFTP and mount root " \
"filesystem over NFS; " \
"echo Set partitionset_active variable to 'A' " \
"or 'B' to select kernel and rootfs partition; " \
"echo" \
"\0"
/*
* Variant 1 partition layout
* chip-size = 256MiB
*| name | size | address area |
*-------------------------------------------------------
*| spl | 128.000 KiB | 0x 0..0x 1ffff |
*| spl.backup1 | 128.000 KiB | 0x 20000..0x 3ffff |
*| spl.backup2 | 128.000 KiB | 0x 40000..0x 5ffff |
*| spl.backup3 | 128.000 KiB | 0x 60000..0x 7ffff |
*| u-boot | 1.875 MiB | 0x 80000..0x 25ffff |
*| uboot.env | 128.000 KiB | 0x 260000..0x 27ffff |
*| kernel_a | 5.000 MiB | 0x 280000..0x 77ffff |
*| kernel_b | 5.000 MiB | 0x 780000..0x c7ffff |
*| mtdoops | 8.000 MiB | 0x c80000..0x 147ffff |
*| rootfs | 235.500 MiB | 0x 1480000..0x fffffff |
*-------------------------------------------------------
"mtdparts=omap2-nand.0:" \
"128k(spl)," \
"128k(spl.backup1)," \
"128k(spl.backup2)," \
"128k(spl.backup3)," \
"1920k(u-boot)," \
"128k(uboot.env)," \
"5120k(kernel_a)," \
"5120k(kernel_b)," \
"8192k(mtdoops)," \
"-(rootfs)"
*/
#define DFU_ALT_INFO_NAND_V1 \
"spl part 0 1;" \
"spl.backup1 part 0 2;" \
"spl.backup2 part 0 3;" \
"spl.backup3 part 0 4;" \
"u-boot part 0 5;" \
"u-boot.env part 0 6;" \
"kernel_a part 0 7;" \
"kernel_b part 0 8;" \
"rootfs partubi 0 10"
#define CONFIG_ENV_SETTINGS_NAND_V1 \
"nand_active_ubi_vol=rootfs_a\0" \
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"nand_active_ubi_vol_A=rootfs_a\0" \
"nand_active_ubi_vol_B=rootfs_b\0" \
"nand_root_fs_type=ubifs rootwait=1\0" \
"nand_src_addr=0x280000\0" \
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"nand_src_addr_A=0x280000\0" \
"nand_src_addr_B=0x780000\0" \
"nand_args=run bootargs_defaults;" \
"mtdparts default;" \
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"setenv ${partitionset_active} true;" \
"if test -n ${A}; then " \
"setenv nand_active_ubi_vol ${nand_active_ubi_vol_A};" \
"setenv nand_src_addr ${nand_src_addr_A};" \
"fi;" \
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"if test -n ${B}; then " \
"setenv nand_active_ubi_vol ${nand_active_ubi_vol_B};" \
"setenv nand_src_addr ${nand_src_addr_B};" \
"fi;" \
"setenv nand_root ubi0:${nand_active_ubi_vol} rw " \
"ubi.mtd=9,${ubi_off};" \
"setenv bootargs ${bootargs} " \
"root=${nand_root} noinitrd ${mtdparts} " \
"rootfstype=${nand_root_fs_type} ip=${ip_method} " \
"console=ttyMTD,mtdoops console=ttyO0,115200n8 mtdoops.mtddev" \
"=mtdoops\0" \
COMMON_ENV_DFU_ARGS \
"dfu_alt_info=" DFU_ALT_INFO_NAND_V1 "\0" \
COMMON_ENV_NAND_BOOT \
"nand read.i ${kloadaddr} ${nand_src_addr} " \
"${nand_img_size}; bootm ${kloadaddr}\0" \
COMMON_ENV_NAND_CMDS
#define CONFIG_ENV_SETTINGS_V1 \
COMMON_ENV_SETTINGS \
"net_args=run bootargs_defaults;" \
"mtdparts default;" \
"setenv bootfile ${project_dir}/kernel/uImage;" \
"setenv rootpath /home/projects/${project_dir}/rootfs;" \
"setenv bootargs ${bootargs} " \
"root=/dev/nfs ${mtdparts} " \
"nfsroot=${serverip}:${rootpath},${nfsopts} " \
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"ip=${ipaddr}:${serverip}:" \
"${gatewayip}:${netmask}:${hostname}:eth0:off\0" \
"net_nfs=echo Booting from network ...; " \
"run net_args; " \
"tftpboot ${kloadaddr} ${serverip}:${bootfile}; " \
"bootm ${kloadaddr}\0"
/*
* Variant 2 partition layout (default)
* chip-size = 256MiB or 512 MiB
*| name | size | address area |
*-------------------------------------------------------
*| spl | 128.000 KiB | 0x 0..0x 1ffff |
*| spl.backup1 | 128.000 KiB | 0x 20000..0x 3ffff |
*| spl.backup2 | 128.000 KiB | 0x 40000..0x 5ffff |
*| spl.backup3 | 128.000 KiB | 0x 60000..0x 7ffff |
*| u-boot | 1.875 MiB | 0x 80000..0x 25ffff |
*| uboot.env0 | 512.000 KiB | 0x 260000..0x 2Dffff |
*| uboot.env1 | 512.000 KiB | 0x 2E0000..0x 35ffff |
*| mtdoops | 512.000 KiB | 0x 360000..0x 3dffff |
*| (256) rootfs | 252.125 MiB | 0x 3E0000..0x fffffff |
*| (512) rootfs | 508.125 MiB | 0x 3E0000..0x1fffffff |
*-------------------------------------------------------
*/
#define DFU_ALT_INFO_NAND_V2 \
"spl part 0 1;" \
"spl.backup1 part 0 2;" \
"spl.backup2 part 0 3;" \
"spl.backup3 part 0 4;" \
"u-boot part 0 5;" \
"u-boot.env0 part 0 6;" \
"u-boot.env1 part 0 7;" \
"rootfs partubi 0 9" \
#define CONFIG_ENV_SETTINGS_NAND_V2 \
"nand_active_ubi_vol=rootfs_a\0" \
"rootfs_name=rootfs\0" \
"kernel_name=uImage\0"\
"nand_root_fs_type=ubifs rootwait=1\0" \
"nand_args=run bootargs_defaults;" \
"mtdparts default;" \
"setenv ${partitionset_active} true;" \
"if test -n ${A}; then " \
"setenv nand_active_ubi_vol ${rootfs_name}_a;" \
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"fi;" \
"if test -n ${B}; then " \
"setenv nand_active_ubi_vol ${rootfs_name}_b;" \
"fi;" \
"setenv nand_root ubi0:${nand_active_ubi_vol} rw " \
"ubi.mtd=rootfs,2048;" \
"setenv bootargs ${bootargs} " \
"root=${nand_root} noinitrd ${mtdparts} " \
"rootfstype=${nand_root_fs_type} ip=${ip_method} " \
"console=ttyMTD,mtdoops console=ttyO0,115200n8 mtdoops.mtddev" \
"=mtdoops\0" \
COMMON_ENV_DFU_ARGS \
"dfu_alt_info=" DFU_ALT_INFO_NAND_V2 "\0" \
COMMON_ENV_NAND_BOOT \
"ubi part rootfs ${ubi_off};" \
"ubifsmount ubi0:${nand_active_ubi_vol};" \
"ubifsload ${kloadaddr} boot/${kernel_name};" \
"ubifsload ${loadaddr} boot/${dtb_name}.dtb;" \
"bootm ${kloadaddr} - ${loadaddr}\0" \
"nand_boot_backup=ubifsload ${loadaddr} boot/am335x-draco.dtb;" \
"bootm ${kloadaddr} - ${loadaddr}\0" \
COMMON_ENV_NAND_CMDS
#define CONFIG_ENV_SETTINGS_V2 \
COMMON_ENV_SETTINGS \
"net_args=run bootargs_defaults;" \
"mtdparts default;" \
"setenv bootfile ${project_dir}/kernel/uImage;" \
"setenv bootdtb ${project_dir}/kernel/dtb;" \
"setenv rootpath /home/projects/${project_dir}/rootfs;" \
"setenv bootargs ${bootargs} " \
"root=/dev/nfs ${mtdparts} " \
"nfsroot=${serverip}:${rootpath},${nfsopts} " \
"ip=${ipaddr}:${serverip}:" \
"${gatewayip}:${netmask}:${hostname}:eth0:off\0" \
"net_nfs=echo Booting from network ...; " \
"run net_args; " \
"tftpboot ${kloadaddr} ${serverip}:${bootfile}; " \
"tftpboot ${loadaddr} ${serverip}:${bootdtb}; " \
"bootm ${kloadaddr} - ${loadaddr}\0"
/*
* Variant 3 partition layout
* chip-size = 512MiB
*| name | size | address area |
*-------------------------------------------------------
*| spl | 128.000 KiB | 0x 0..0x 1ffff |
*| spl.backup1 | 128.000 KiB | 0x 20000..0x 3ffff |
*| spl.backup2 | 128.000 KiB | 0x 40000..0x 5ffff |
*| spl.backup3 | 128.000 KiB | 0x 60000..0x 7ffff |
*| u-boot | 1.875 MiB | 0x 80000..0x 25ffff |
*| uboot.env0 | 512.000 KiB | 0x 260000..0x 2Dffff |
*| uboot.env1 | 512.000 KiB | 0x 2E0000..0x 35ffff |
*| rootfs | 300.000 MiB | 0x 360000..0x12f5ffff |
*| mtdoops | 512.000 KiB | 0x12f60000..0x12fdffff |
*|configuration | 104.125 MiB | 0x12fe0000..0x1fffffff |
*-------------------------------------------------------
"mtdparts=omap2-nand.0:" \
"128k(spl)," \
"128k(spl.backup1)," \
"128k(spl.backup2)," \
"128k(spl.backup3)," \
"1920k(u-boot)," \
"512k(u-boot.env0)," \
"512k(u-boot.env1)," \
"300m(rootfs)," \
"512k(mtdoops)," \
"-(configuration)"
*/
#define CONFIG_SYS_NAND_BASE (0x08000000) /* physical address */
/* to access nand at */
/* CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND
devices */
#if !defined(CONFIG_SPI_BOOT)
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#endif
#endif
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
/* Reboot after 60 sec if bootcmd fails */
#define CONFIG_RESET_TO_RETRY
#define CONFIG_BOOT_RETRY_TIME 60
#endif /* ! __CONFIG_SIEMENS_AM33X_COMMON_H */