Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-17 16:53:06 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/doc/board/sifive/unmatched.rst

573 lines
28 KiB
ReStructuredText
Raw Normal View History

board: sifive: add HiFive Unmatched board support Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-27 13:52:13 +00:00
.. SPDX-License-Identifier: GPL-2.0+
HiFive Unmatched
================
FU740-C000 RISC-V SoC
---------------------
The FU740-C000 is a 4+1 64-bit RISC-V core SoC from SiFive.
The HiFive Unmatched development platform is based on FU740-C000 and capable
of running Linux.
Mainline support
----------------
The support for following drivers are already enabled:
1. SiFive UART Driver.
2. SiFive PRCI Driver for clock.
3. Cadence MACB ethernet driver for networking support.
4. SiFive SPI Driver.
5. MMC SPI Driver for MMC/SD support.
doc: describe MSEL settings for booting from SD card unmatched.rst describes booting from SD card or from SPI. But only for booting from SPI the boot selection settings are described. Add the missing information. Fix a typo 'uSD'. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-01-27 01:50:28 +00:00
Booting from micro SD card using U-Boot SPL
-------------------------------------------
Booting from an SD card requires that the boot mode selection DIP switches
MSEL[3:0] are set to 1011.
board: sifive: add HiFive Unmatched board support Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-27 13:52:13 +00:00
Building
--------
Before building U-Boot SPL, OpenSBI must be built first. OpenSBI can be
cloned and built for FU740 as below:
.. code-block:: console
git clone https://github.com/riscv/opensbi.git
cd opensbi
make PLATFORM=generic
export OPENSBI=<path to opensbi/build/platform/generic/firmware/fw_dynamic.bin>
Now build the U-Boot SPL and U-Boot proper
.. code-block:: console
cd <U-Boot-dir>
make sifive_unmatched_defconfig
make
This will generate spl/u-boot-spl.bin and u-boot.itb
Flashing
--------
ZSBL loads the U-Boot SPL (u-boot-spl.bin) from a partition with GUID type
5B193300-FC78-40CD-8002-E86C45580B47
doc: correct HiFive Unmatched boot description Main U-Boot is loaded by sector number, not by partition GUID type. Fixes: 70415e1e528d ("board: sifive: add HiFive Unmatched board support") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2023-05-01 12:47:52 +00:00
With the default configuration U-Boot SPL expects u-boot.itb starting at sector
2082 (CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x822). It is recommended to use a
partition with type GUID 2E54B353-1271-4842-806F-E436D6AF6985 for storing
main U-Boot.
board: sifive: add HiFive Unmatched board support Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-27 13:52:13 +00:00
u-boot.itb is a combination of fw_dynamic.bin, u-boot-nodtb.bin and
device tree blob (hifive-unmatched-a00.dtb)
Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)
doc: riscv: flashing SiFive boards We should not use /dev/sda and /dev/sdb in our examples. Users might inadvertently mess up their workstation. Use /dev/sdX instead. Remove console output like '# ' and '> ' which makes copying hard. Set example language to bash for correct syntax-highlighting. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> iewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-07-28 08:52:53 +00:00
.. code-block:: bash
board: sifive: add HiFive Unmatched board support Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-27 13:52:13 +00:00
doc: riscv: flashing SiFive boards We should not use /dev/sda and /dev/sdb in our examples. Users might inadvertently mess up their workstation. Use /dev/sdX instead. Remove console output like '# ' and '> ' which makes copying hard. Set example language to bash for correct syntax-highlighting. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> iewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-07-28 08:52:53 +00:00
sudo sgdisk -g --clear -a 1 \
--new=1:34:2081 --change-name=1:spl --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
--new=2:2082:10273 --change-name=2:uboot --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
--new=3:16384:282623 --change-name=3:boot --typecode=3:0x0700 \
--new=4:286720:13918207 --change-name=4:root --typecode=4:0x8300 \
/dev/sdX
board: sifive: add HiFive Unmatched board support Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-27 13:52:13 +00:00
Copy linux Image.gz and hifive-unmatched-a00.dtb to boot partition
doc: riscv: flashing SiFive boards We should not use /dev/sda and /dev/sdb in our examples. Users might inadvertently mess up their workstation. Use /dev/sdX instead. Remove console output like '# ' and '> ' which makes copying hard. Set example language to bash for correct syntax-highlighting. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> iewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-07-28 08:52:53 +00:00
.. code-block:: bash
board: sifive: add HiFive Unmatched board support Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-27 13:52:13 +00:00
doc: riscv: flashing SiFive boards We should not use /dev/sda and /dev/sdb in our examples. Users might inadvertently mess up their workstation. Use /dev/sdX instead. Remove console output like '# ' and '> ' which makes copying hard. Set example language to bash for correct syntax-highlighting. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> iewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-07-28 08:52:53 +00:00
sudo mkfs.vfat /dev/sdX3
sudo mkfs.ext4 /dev/sdX4
board: sifive: add HiFive Unmatched board support Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-27 13:52:13 +00:00
doc: riscv: flashing SiFive boards We should not use /dev/sda and /dev/sdb in our examples. Users might inadvertently mess up their workstation. Use /dev/sdX instead. Remove console output like '# ' and '> ' which makes copying hard. Set example language to bash for correct syntax-highlighting. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> iewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-07-28 08:52:53 +00:00
sudo mount /dev/sdX3 /media/sdX3
sudo cp Image.gz hifive-unmatched-a00.dtb /media/sdX3/
board: sifive: add HiFive Unmatched board support Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-27 13:52:13 +00:00
Program the SD card
doc: riscv: flashing SiFive boards We should not use /dev/sda and /dev/sdb in our examples. Users might inadvertently mess up their workstation. Use /dev/sdX instead. Remove console output like '# ' and '> ' which makes copying hard. Set example language to bash for correct syntax-highlighting. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> iewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-07-28 08:52:53 +00:00
.. code-block:: bash
board: sifive: add HiFive Unmatched board support Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-27 13:52:13 +00:00
doc: riscv: flashing SiFive boards We should not use /dev/sda and /dev/sdb in our examples. Users might inadvertently mess up their workstation. Use /dev/sdX instead. Remove console output like '# ' and '> ' which makes copying hard. Set example language to bash for correct syntax-highlighting. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> iewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-07-28 08:52:53 +00:00
sudo dd if=spl/u-boot-spl.bin of=/dev/sdX seek=34
sudo dd if=u-boot.itb of=/dev/sdX seek=2082
board: sifive: add HiFive Unmatched board support Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-27 13:52:13 +00:00
Booting
-------
Once you plugin the sdcard and power up, you should see the U-Boot prompt.
Loading the kernel and dtb
.. code-block:: none
fatload mmc 0:3 ${kernel_addr_r} Image.gz
fatload mmc 0:3 ${fdt_addr_r} hifive-unmatched-a00.dtb
booti ${kernel_addr_r} - ${fdt_addr_r}
Sample boot log from HiFive Unmatched board
-------------------------------------------
.. code-block:: none
U-Boot SPL 2021.04-rc4-00009-g7d70643cc3-dirty (Mar 16 2021 - 18:03:14 +0800)
Trying to boot from MMC1
U-Boot 2021.04-rc4-00009-g7d70643cc3-dirty (Mar 16 2021 - 18:03:14 +0800)
CPU: rv64imafdc
Model: SiFive HiFive Unmatched A00
DRAM: 16 GiB
MMC: spi@10050000:mmc@0: 0
In: serial@10010000
Out: serial@10010000
Err: serial@10010000
Model: SiFive HiFive Unmatched A00
Net:
Error: ethernet@10090000 address not set.
No ethernet found.
Hit any key to stop autoboot: 0
PCIe Link up, Gen1
Device 0: Vendor: 0x126f Rev: S1111A0L Prod: AA000000000000001995
Type: Hard Disk
Capacity: 488386.3 MB = 476.9 GB (1000215216 x 512)
... is now current device
Scanning nvme 0:1...
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disk mmc@0.blk...
** Unrecognized filesystem type **
** Unrecognized filesystem type **
Scanning disk nvme#0.blk#0...
Found 8 disks
No EFI system partition
Error: ethernet@10090000 address not set.
BootOrder not defined
EFI boot manager: Cannot load any image
starting USB...
Bus xhci_pci: Register 4000840 NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus xhci_pci for devices... 3 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:3...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
205 bytes read in 9 ms (21.5 KiB/s)
1: OpenEmbedded-SiFive-HiFive-Unmatched
Retrieving file: /Image.gz
7225919 bytes read in 4734 ms (1.5 MiB/s)
append: root=/dev/mmcblk0p4 rootfstype=ext4 rootwait console=ttySIF0,115200 earlycon=sbi
Retrieving file: /hifive-unmatched-a00.dtb
10445 bytes read in 13 ms (784.2 KiB/s)
Uncompressing Kernel Image
Moving Image from 0x84000000 to 0x80200000, end=81629000
## Flattened Device Tree blob at 88000000
Booting using the fdt blob at 0x88000000
Using Device Tree in place at 0000000088000000, end 00000000880058cc
Starting kernel ...
[ 0.000000] Linux version 5.10.15 (oe-user@oe-host) (riscv64-oe-linux-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.0.201
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '')
[ 0.000000] printk: bootconsole [sbi0] enabled
[ 0.000000] efi: UEFI not found.
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000027fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x000000027fffffff]
[ 0.000000] Zeroed struct page in unavailable ranges: 512 pages
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff]
[ 0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB)
[ 0.000000] SBI specification v0.3 detected
[ 0.000000] SBI implementation ID=0x1 Version=0x9
[ 0.000000] SBI v0.2 TIME extension detected
[ 0.000000] SBI v0.2 IPI extension detected
[ 0.000000] SBI v0.2 RFENCE extension detected
[ 0.000000] SBI v0.2 HSM extension detected
[ 0.000000] CPU with hartid=0 is not available
[ 0.000000] CPU with hartid=0 is not available
[ 0.000000] riscv: ISA extensions acdfim
[ 0.000000] riscv: ELF capabilities acdfim
[ 0.000000] percpu: Embedded 26 pages/cpu s66904 r8192 d31400 u106496
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975
[ 0.000000] Kernel command line: root=/dev/mmcblk0p4 rootfstype=ext4 rootwait console=ttySIF0,115200 earlycon=sbi
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Sorting __ex_table...
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 8155880K/8386560K available (8490K kernel code, 5515K rwdata, 4096K rodata, 285K init, 383K bss, 23)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] CPU with hartid=0 is not available
[ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller
[ 0.000000] riscv-intc: 64 local interrupts mapped
[ 0.000000] plic: interrupt-controller@c000000: mapped 69 interrupts with 4 handlers for 9 contexts.
[ 0.000000] random: get_random_bytes called from 0xffffffe000002a6a with crng_init=0
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 352636161696s
[ 0.000007] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns
[ 0.008626] Console: colour dummy device 80x25
[ 0.013049] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=4000)
[ 0.023115] pid_max: default: 32768 minimum: 301
[ 0.028423] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.035919] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.045957] rcu: Hierarchical SRCU implementation.
[ 0.050393] EFI services will not be available.
[ 0.055132] smp: Bringing up secondary CPUs ...
[ 0.061824] smp: Brought up 1 node, 4 CPUs
[ 0.067458] devtmpfs: initialized
[ 0.072700] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.081789] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.089738] NET: Registered protocol family 16
[ 0.093999] thermal_sys: Registered thermal governor 'step_wise'
[ 0.109208] iommu: Default domain type: Translated
[ 0.119694] vgaarb: loaded
[ 0.122571] SCSI subsystem initialized
[ 0.126499] usbcore: registered new interface driver usbfs
[ 0.131686] usbcore: registered new interface driver hub
[ 0.137071] usbcore: registered new device driver usb
[ 0.142286] EDAC MC: Ver: 3.0.0
[ 0.145760] Advanced Linux Sound Architecture Driver Initialized.
[ 0.152205] clocksource: Switched to clocksource riscv_clocksource
[ 1.046286] VFS: Disk quotas dquot_6.6.0
[ 1.049651] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.062844] NET: Registered protocol family 2
[ 1.067172] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 1.075455] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 1.085428] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 1.096548] TCP: Hash tables configured (established 65536 bind 65536)
[ 1.103043] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 1.109879] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 1.117413] NET: Registered protocol family 1
[ 1.121881] RPC: Registered named UNIX socket transport module.
[ 1.127139] RPC: Registered udp transport module.
[ 1.131901] RPC: Registered tcp transport module.
[ 1.136677] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.143194] PCI: CLS 0 bytes, default 64
[ 1.148359] Initialise system trusted keyrings
[ 1.152364] workingset: timestamp_bits=62 max_order=21 bucket_order=0
[ 1.165382] NFS: Registering the id_resolver key type
[ 1.169781] Key type id_resolver registered
[ 1.174011] Key type id_legacy registered
[ 1.178179] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.184874] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.192453] 9p: Installing v9fs 9p2000 file system support
[ 1.198116] NET: Registered protocol family 38
[ 1.201886] Key type asymmetric registered
[ 1.206046] Asymmetric key parser 'x509' registered
[ 1.211029] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.218468] io scheduler mq-deadline registered
[ 1.223072] io scheduler kyber registered
[ 1.228803] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 1.235017] fu740-pcie e00000000.pcie: FPGA PCIE PROBE
[ 1.281706] fu740-pcie e00000000.pcie: PCIE-PERSTN is GPIO 504
[ 1.286922] fu740-pcie e00000000.pcie: PWREN is GPIO 501
[ 1.292377] fu740-pcie e00000000.pcie: host bridge /soc/pcie@e00000000 ranges:
[ 1.299603] fu740-pcie e00000000.pcie: IO 0x0060080000..0x006008ffff -> 0x0060080000
[ 1.307922] fu740-pcie e00000000.pcie: MEM 0x0060090000..0x0070ffffff -> 0x0060090000
[ 1.316244] fu740-pcie e00000000.pcie: MEM 0x2000000000..0x3fffffffff -> 0x2000000000
[ 1.432223] fu740-pcie e00000000.pcie: PWREN enabling
[ 1.436607] fu740-pcie e00000000.pcie: PWREN valid
[ 1.560226] fu740-pcie e00000000.pcie: invalid resource
[ 1.664802] fu740-pcie e00000000.pcie: Link up
[ 1.768582] fu740-pcie e00000000.pcie: Link up
[ 1.872369] fu740-pcie e00000000.pcie: Link up
[ 1.876116] fu740-pcie e00000000.pcie: Link up, Gen3
[ 1.881352] fu740-pcie e00000000.pcie: PCI host bridge to bus 0000:00
[ 1.887700] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.893247] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0x60080000-0x6008ffff])
[ 1.902807] pci_bus 0000:00: root bus resource [mem 0x60090000-0x70ffffff]
[ 1.909748] pci_bus 0000:00: root bus resource [mem 0x2000000000-0x3fffffffff pref]
[ 1.917517] pci 0000:00:00.0: [f15e:0000] type 01 class 0x060400
[ 1.923569] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 1.929902] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[ 1.936723] pci 0000:00:00.0: supports D1
[ 1.940755] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.947619] pci 0000:01:00.0: [1b21:2824] type 01 class 0x060400
[ 1.953052] pci 0000:01:00.0: enabling Extended Tags
[ 1.958165] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.976890] pci 0000:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.984425] pci 0000:02:00.0: [1b21:2824] type 01 class 0x060400
[ 1.990396] pci 0000:02:00.0: enabling Extended Tags
[ 1.995509] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 2.001938] pci 0000:02:02.0: [1b21:2824] type 01 class 0x060400
[ 2.007682] pci 0000:02:02.0: enabling Extended Tags
[ 2.012793] pci 0000:02:02.0: PME# supported from D0 D3hot D3cold
[ 2.019167] pci 0000:02:03.0: [1b21:2824] type 01 class 0x060400
[ 2.024966] pci 0000:02:03.0: enabling Extended Tags
[ 2.030075] pci 0000:02:03.0: PME# supported from D0 D3hot D3cold
[ 2.036468] pci 0000:02:04.0: [1b21:2824] type 01 class 0x060400
[ 2.042250] pci 0000:02:04.0: enabling Extended Tags
[ 2.047359] pci 0000:02:04.0: PME# supported from D0 D3hot D3cold
[ 2.053811] pci 0000:02:08.0: [1b21:2824] type 01 class 0x060400
[ 2.059534] pci 0000:02:08.0: enabling Extended Tags
[ 2.064647] pci 0000:02:08.0: PME# supported from D0 D3hot D3cold
[ 2.071499] pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.078837] pci 0000:02:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.086911] pci 0000:02:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.094987] pci 0000:02:04.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.103075] pci 0000:02:08.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.111901] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 03
[ 2.118031] pci 0000:04:00.0: [1b21:1142] type 00 class 0x0c0330
[ 2.123968] pci 0000:04:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 2.131038] pci 0000:04:00.0: PME# supported from D3cold
[ 2.148888] pci_bus 0000:04: busn_res: [bus 04-ff] end is updated to 04
[ 2.155588] pci_bus 0000:05: busn_res: [bus 05-ff] end is updated to 05
[ 2.162286] pci_bus 0000:06: busn_res: [bus 06-ff] end is updated to 06
[ 2.168408] pci 0000:07:00.0: [126f:2263] type 00 class 0x010802
[ 2.174351] pci 0000:07:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
[ 2.192890] pci_bus 0000:07: busn_res: [bus 07-ff] end is updated to 07
[ 2.198837] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 07
[ 2.205522] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 07
[ 2.212241] pci 0000:00:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff]
[ 2.219067] pci 0000:00:00.0: BAR 14: assigned [mem 0x60200000-0x603fffff]
[ 2.226010] pci 0000:00:00.0: BAR 6: assigned [mem 0x60090000-0x6009ffff pref]
[ 2.233308] pci 0000:01:00.0: BAR 14: assigned [mem 0x60200000-0x603fffff]
[ 2.240259] pci 0000:02:02.0: BAR 14: assigned [mem 0x60200000-0x602fffff]
[ 2.247203] pci 0000:02:08.0: BAR 14: assigned [mem 0x60300000-0x603fffff]
[ 2.254150] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 2.259217] pci 0000:04:00.0: BAR 0: assigned [mem 0x60200000-0x60207fff 64bit]
[ 2.266594] pci 0000:02:02.0: PCI bridge to [bus 04]
[ 2.271615] pci 0000:02:02.0: bridge window [mem 0x60200000-0x602fffff]
[ 2.278485] pci 0000:02:03.0: PCI bridge to [bus 05]
[ 2.283529] pci 0000:02:04.0: PCI bridge to [bus 06]
[ 2.288572] pci 0000:07:00.0: BAR 0: assigned [mem 0x60300000-0x60303fff 64bit]
[ 2.295952] pci 0000:02:08.0: PCI bridge to [bus 07]
[ 2.300973] pci 0000:02:08.0: bridge window [mem 0x60300000-0x603fffff]
[ 2.307842] pci 0000:01:00.0: PCI bridge to [bus 02-07]
[ 2.313133] pci 0000:01:00.0: bridge window [mem 0x60200000-0x603fffff]
[ 2.320009] pci 0000:00:00.0: PCI bridge to [bus 01-07]
[ 2.325288] pci 0000:00:00.0: bridge window [mem 0x60200000-0x603fffff]
[ 2.332808] pcieport 0000:00:00.0: AER: enabled with IRQ 51
[ 2.337946] pcieport 0000:01:00.0: enabling device (0000 -> 0002)
[ 2.344786] pcieport 0000:02:02.0: enabling device (0000 -> 0002)
[ 2.351328] pcieport 0000:02:08.0: enabling device (0000 -> 0002)
[ 2.357091] pci 0000:04:00.0: enabling device (0000 -> 0002)
[ 2.362751] switchtec: loaded.
[ 2.365933] L2CACHE: DataError @ 0x00000003.00964470
[ 2.365992] L2CACHE: No. of Banks in the cache: 4
[ 2.375414] L2CACHE: No. of ways per bank: 16
[ 2.379846] L2CACHE: Sets per bank: 512
[ 2.383751] L2CACHE: Bytes per cache block: 64
[ 2.388267] L2CACHE: Index of the largest way enabled: 15
[ 2.434865] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.441695] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 115200) is a SiFive UART v0
[ 2.450625] printk: console [ttySIF0] enabled
[ 2.450625] printk: console [ttySIF0] enabled
[ 2.459360] printk: bootconsole [sbi0] disabled
[ 2.459360] printk: bootconsole [sbi0] disabled
[ 2.468824] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 115200) is a SiFive UART v0
[ 2.493853] loop: module loaded
[ 2.526475] nvme nvme0: pci function 0000:07:00.0
[ 2.530852] nvme 0000:07:00.0: enabling device (0000 -> 0002)
[ 2.537716] Rounding down aligned max_sectors from 4294967295 to 4294967288
[ 2.544470] db_root: cannot open: /etc/target
[ 2.545926] nvme nvme0: allocated 64 MiB host memory buffer.
[ 2.549020] sifive_spi 10040000.spi: mapped; irq=4, cs=1
[ 2.559941] spi-nor spi0.0: is25wp256 (32768 Kbytes)
[ 2.566431] sifive_spi 10050000.spi: mapped; irq=6, cs=1
[ 2.566707] nvme nvme0: 4/0/0 default/read/poll queues
[ 2.571935] libphy: Fixed MDIO Bus: probed
[ 2.580950] macb 10090000.ethernet: Registered clk switch 'sifive-gemgxl-mgmt'
[ 2.587536] macb 10090000.ethernet: invalid hw address, using random
[ 2.588100] nvme0n1: p1 p2
[ 2.593875] BEU: Load or Store TILINK BUS ERR occurred
[ 2.594342] libphy: MACB_mii_bus: probed
[ 2.599312] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 7 (5e:57:b8:ab:24:4a)
[ 2.615501] e1000e: Intel(R) PRO/1000 Network Driver
[ 2.620251] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 2.626463] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.632684] ehci-pci: EHCI PCI platform driver
[ 2.637144] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.643273] ohci-pci: OHCI PCI platform driver
[ 2.647731] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.654315] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 2.659450] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 1
[ 2.807373] xhci_hcd 0000:04:00.0: hcc params 0x0200e081 hci version 0x100 quirks 0x0000000010000410
[ 2.816609] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.824115] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.831312] usb usb1: Product: xHCI Host Controller
[ 2.836174] usb usb1: Manufacturer: Linux 5.10.15 xhci-hcd
[ 2.841652] usb usb1: SerialNumber: 0000:04:00.0
[ 2.846639] hub 1-0:1.0: USB hub found
[ 2.850037] hub 1-0:1.0: 2 ports detected
[ 2.854306] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 2.859335] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 2
[ 2.866599] xhci_hcd 0000:04:00.0: Host supports USB 3.0 SuperSpeed
[ 2.873638] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.881074] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 2.889212] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.896422] usb usb2: Product: xHCI Host Controller
[ 2.901282] usb usb2: Manufacturer: Linux 5.10.15 xhci-hcd
[ 2.906752] usb usb2: SerialNumber: 0000:04:00.0
[ 2.911671] hub 2-0:1.0: USB hub found
[ 2.915130] hub 2-0:1.0: 2 ports detected
[ 2.919486] usbcore: registered new interface driver usb-storage
[ 2.925212] usbcore: registered new interface driver usbserial_generic
[ 2.931620] usbserial: USB Serial support registered for generic
[ 2.937771] mousedev: PS/2 mouse device common for all mice
[ 2.943220] usbcore: registered new interface driver usbtouchscreen
[ 2.949466] i2c /dev entries driver
[ 2.954218] lm90 0-004c: supply vcc not found, using dummy regulator
[ 2.961629] EDAC DEVICE0: Giving out device to module Sifive ECC Manager controller sifive_edac.0: DEV sifive_edac.0 (I)
[ 2.997874] mmc_spi spi1.0: SD/MMC host mmc0, no DMA, no WP, no poweroff, cd polling
[ 3.005138] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.010980] usbcore: registered new interface driver usbhid
[ 3.016407] usbhid: USB HID core driver
[ 3.020540] usbcore: registered new interface driver snd-usb-audio
[ 3.027209] NET: Registered protocol family 10
[ 3.031878] Segment Routing with IPv6
[ 3.034864] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.041232] NET: Registered protocol family 17
[ 3.045324] 9pnet: Installing 9P2000 support
[ 3.049397] Key type dns_resolver registered
[ 3.053786] Loading compiled-in X.509 certificates
[ 3.059729] ALSA device list:
[ 3.061943] No soundcards found.
[ 3.066057] Waiting for root device /dev/mmcblk0p4...
[ 3.077319] mmc0: host does not support reading read-only switch, assuming write-enable
[ 3.084564] mmc0: new SDHC card on SPI
[ 3.089699] mmcblk0: mmc0:0000 SD32G 29.7 GiB
[ 3.126488] GPT:Primary header thinks Alt. header is not at the end of the disk.
[ 3.133144] GPT:13918241 != 62333951
[ 3.136679] GPT:Alternate GPT header not at the end of the disk.
[ 3.142673] GPT:13918241 != 62333951
[ 3.146231] GPT: Use GNU Parted to correct GPT errors.
[ 3.151398] mmcblk0: p1 p2 p3 p4
[ 3.212226] usb 1-2: new high-speed USB device number 2 using xhci_hcd
[ 3.258310] EXT4-fs (mmcblk0p4): INFO: recovery required on readonly filesystem
[ 3.264855] EXT4-fs (mmcblk0p4): write access will be enabled during recovery
[ 3.458247] usb 1-2: New USB device found, idVendor=174c, idProduct=2074, bcdDevice= 0.01
[ 3.465662] usb 1-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 3.472775] usb 1-2: Product: AS2107
[ 3.476336] usb 1-2: Manufacturer: ASMedia
[ 3.480419] usb 1-2: SerialNumber: USB2.0 Hub
[ 3.533583] EXT4-fs (mmcblk0p4): recovery complete
[ 3.543756] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
[ 3.551132] VFS: Mounted root (ext4 filesystem) readonly on device 179:4.
[ 3.554682] hub 1-2:1.0: USB hub found
[ 3.561105] devtmpfs: mounted
[ 3.561778] hub 1-2:1.0: 4 ports detected
[ 3.565546] Freeing unused kernel memory: 284K
[ 3.572964] Kernel memory protection not selected by kernel config.
[ 3.579225] Run /sbin/init as init process
[ 3.613136] usb 2-2: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 3.643539] usb 2-2: New USB device found, idVendor=174c, idProduct=3074, bcdDevice= 0.01
[ 3.650948] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 3.658072] usb 2-2: Product: AS2107
[ 3.661630] usb 2-2: Manufacturer: ASMedia
[ 3.665709] usb 2-2: SerialNumber: USB2.0 Hub
[ 3.762380] hub 2-2:1.0: USB hub found
[ 3.766074] hub 2-2:1.0: 4 ports detected
[ 7.487226] systemd[1]: System time before build time, advancing clock.
[ 7.788093] systemd[1]: systemd 247.2+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +U)
[ 7.809694] systemd[1]: Detected architecture riscv64.
Welcome to OpenEmbedded nodistro.0!
[ 7.832648] systemd[1]: Set hostname to <unmatched>.
[ 9.397499] systemd[1]: Queued start job for default target Multi-User System.
[ 9.408518] random: systemd: uninitialized urandom read (16 bytes read)
[ 9.429329] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 9.440400] random: systemd: uninitialized urandom read (16 bytes read)
[ 9.447086] systemd[1]: Created slice system-modprobe.slice.
[ OK ] Created slice system-modprobe.slice.
[ 9.458480] random: systemd: uninitialized urandom read (16 bytes read)
[ 9.465436] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 9.478594] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 9.490225] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password <20><>…ts to Console Directory Watch.
[ 9.506407] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password R<><52>…uests to Wall Directory Watch.
[ 9.522312] systemd[1]: Reached target Paths.
[ OK ] Reached target Paths.
[ 9.531078] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 9.542855] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 9.552712] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 9.561566] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 9.578686] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 9.586545] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[snip]
[ OK ] Reached target System Time Synchronized.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started D-Bus System Message Bus.
Starting User Login Management...
Starting Permit User Sessions...
[ OK ] Started Xinetd A Powerful Replacement For Inetd.
[ OK ] Finished Permit User Sessions.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on hvc0.
[ OK ] Started Serial Getty on ttySIF0.
[ OK ] Reached target Login Prompts.
[ OK ] Started User Login Management.
[ OK ] Reached target Multi-User System.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Finished Update UTMP about System Runlevel Changes.
OpenEmbedded nodistro.0 unmatched hvc0
unmatched login:
OpenEmbedded nodistro.0 unmatched ttySIF0
unmatched login:
riscv: Support booting SiFive Unmatched from SPI. Configure SPI flash devices into SPL. Add SPI boot option to spl.c. Document how to format flash for booting. Signed-off-by: Thomas Skibo <thomas-git@skibo.net> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-11-24 22:32:09 +00:00
Booting from SPI
----------------
Use Building steps from "Booting from uSD using U-Boot SPL" section.
Partition the SPI in Linux via mtdblock. The partition types here are
"HiFive Unleashed FSBL", "HiFive Unleashed BBL", and "U-Boot environment"
for partitions one through three respectively.
.. code-block:: none
sgdisk --clear -a 1 \
--new=1:40:2087 --change-name=1:spl --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
--new=2:2088:10279 --change-name=2:uboot --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
--new=3:10280:10535 --change-name=3:env --typecode=3:3DE21764-95BD-54BD-A5C3-4ABE786F38A8 \
/dev/mtdblock0
Write U-boot SPL and U-boot to their partitions.
.. code-block:: none
doc: path to u-boot-spl.bin on SiFive Unmatched board u-boot-spl.bin is built in spl/. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-03-10 10:32:49 +00:00
dd if=spl/u-boot-spl.bin of=/dev/mtdblock0 bs=4096 seek=5 conv=sync
riscv: Support booting SiFive Unmatched from SPI. Configure SPI flash devices into SPL. Add SPI boot option to spl.c. Document how to format flash for booting. Signed-off-by: Thomas Skibo <thomas-git@skibo.net> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-11-24 22:32:09 +00:00
dd if=u-boot.itb of=/dev/mtdblock0 bs=4096 seek=261 conv=sync
Power off the board.
Change DIP switches MSEL[3:0] to 0110.
Power up the board.
Reference in a new issue Copy permalink