u-boot/include/configs/stm32mp15_common.h

155 lines
4.2 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause */
/*
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved
*
* Configuration settings for the STM32MP15x CPU
*/
#ifndef __CONFIG_STM32MP15_COMMMON_H
#define __CONFIG_STM32MP15_COMMMON_H
#include <linux/sizes.h>
#include <asm/arch/stm32.h>
/*
* Configuration of the external SRAM memory used by U-Boot
*/
#define CONFIG_SYS_SDRAM_BASE STM32_DDR_BASE
/*
* For booting Linux, use the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ SZ_256M
stm32mp1: update memory layout Update the memory layout to be aligned with other platform and avoid overlap with 32MB Linux kernel (multiv7 image). + Kernel => 32MiB offset = 0xC2000000 and increase the bootm size to 32MiB + FDT => 64MiB offset = 0xc4000000 + SCRIPT => 65Mib offset = 0xc4100000 + PXESCRIPT => 66Mib offset = 0xc4200000 + SPLASHIMAGE => 67Mib offset = 0xc4300000 + RAMDISK => 68Mib offset = 0xc4400000 (not limited size) In sources/boot/u-boot/doc/README.distro + kernel_addr_r: A size of 16MB for the kernel is likely adequate. + pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate. + fdt_addr_r: A size of 1MB for the FDT/DTB seems reasonable. + ramdisk_addr_r: It is recommended that this location be highest in RAM out of fdt_addr_, kernel_addr_r, and ramdisk_addr_r, so that the RAM disk can vary in size and use any available RAM. + pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate. + scriptaddr: A size of 1MB for extlinux.conf is more than adequate. For suggestions on memory locations for ARM systems, you must follow the guidelines specified in Documentation/arm/Booting in the Linux kernel tree. And in sources/linux-stm32mp/Documentation/arm/Booting The zImage may also be placed in system RAM and called there. The kernel should be placed in the first 128MiB of RAM. It is recommended that it is loaded above 32MiB in order to avoid the need to relocate prior to decompression, which will make the boot process slightly faster. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-27 16:01:21 +00:00
/* Extend size of kernel image for uncompression */
/*MMC SD*/
#define CONFIG_SYS_MMC_MAX_DEVICE 3
/* NAND support */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
/* Ethernet need */
#ifdef CONFIG_DWC_ETH_QOS
#define CONFIG_SERVERIP 192.168.1.1
#endif
/*****************************************************************************/
#ifdef CONFIG_DISTRO_DEFAULTS
/*****************************************************************************/
#if !defined(CONFIG_SPL_BUILD)
#ifdef CONFIG_CMD_MMC
#define BOOT_TARGET_MMC0(func) func(MMC, mmc, 0)
#define BOOT_TARGET_MMC1(func) func(MMC, mmc, 1)
#define BOOT_TARGET_MMC2(func) func(MMC, mmc, 2)
#else
#define BOOT_TARGET_MMC0(func)
#define BOOT_TARGET_MMC1(func)
#define BOOT_TARGET_MMC2(func)
#endif
#ifdef CONFIG_NET
#define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
#else
#define BOOT_TARGET_PXE(func)
#endif
#ifdef CONFIG_CMD_UBIFS
distroboot: Fix ubifs Fix multiple issues in ubifs distroboot code: U-Boot supports attaching only one MTD device as UBI at the time. So always call 'ubifsmount ubi0:${bootubivol}' for mounting UBI volume ${bootubivol}. Usage of 'ubi${devnum}' is incorrect as 'ubi part' command attach MTD device always as UBI device ubi0. Set distroboot ${bootfstype} variable to ubifs in ubifs_boot command. Distroboot scripts require ${bootfstype} variable to be properly set and it is already set for all other boot types. Set distroboot ${distro_bootpart} variable to ${bootubivol} value. UBI device does not have partitions, but has volumes. Distroboot scripts require something to be set in ${distro_bootpart} variable, so set it to the UBI volume which is currently mounted by ubifs. Set distroboot ${devnum} variable to fixed string "ubi0". ubifs code differs from the other partition code that it requires "ubi" prefix before number. Explicitly unmount ubifs volume after loading all data from it. This allows to detach UBI device from MTD device. Move definition of MTD device with UBI and UBI volume with ubifs filesystem from global env variables ${bootubipart} and ${bootubivol} into the distroboot "func" macro, defined in board include config files. UBIFS distroboot macros then set ${bootubipart} and ${bootubivol} local variables for compatibility with existing distroboot scripts. This last change allows to define more UBIFS target devices and make it clear what is boot MTD/UBI device. All board include config files are adjusted to use this new scheme of specifying boot MTD/UBI device. Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2022-05-31 08:32:36 +00:00
#define BOOT_TARGET_UBIFS(func) func(UBIFS, ubifs, 0, UBI, boot)
#else
#define BOOT_TARGET_UBIFS(func)
#endif
#ifdef CONFIG_CMD_USB
#define BOOT_TARGET_USB(func) func(USB, usb, 0)
#else
#define BOOT_TARGET_USB(func)
#endif
#define BOOT_TARGET_DEVICES(func) \
BOOT_TARGET_MMC1(func) \
BOOT_TARGET_UBIFS(func) \
BOOT_TARGET_MMC0(func) \
BOOT_TARGET_MMC2(func) \
BOOT_TARGET_USB(func) \
BOOT_TARGET_PXE(func)
/*
* default bootcmd for stm32mp15:
* for serial/usb: execute the stm32prog command
* for mmc boot (eMMC, SD card), distro boot on the same mmc device
* for nand or spi-nand boot, distro boot with ubifs on UBI partition
* for nor boot, use the default distro order in ${boot_targets}
*/
#define STM32MP_BOOTCMD "bootcmd_stm32mp=" \
"echo \"Boot over ${boot_device}${boot_instance}!\";" \
"if test ${boot_device} = serial || test ${boot_device} = usb;" \
"then stm32prog ${boot_device} ${boot_instance}; " \
"else " \
"run env_check;" \
"if test ${boot_device} = mmc;" \
"then env set boot_targets \"mmc${boot_instance}\"; fi;" \
"if test ${boot_device} = nand ||" \
" test ${boot_device} = spi-nand ;" \
"then env set boot_targets ubifs0; fi;" \
"run distro_bootcmd;" \
"fi;\0"
#ifdef CONFIG_FASTBOOT_CMD_OEM_FORMAT
/* eMMC default partitions for fastboot command: oem format */
#define STM32MP_PARTS_DEFAULT \
"partitions=" \
"name=ssbl,size=2M;" \
"name=bootfs,size=64MB,bootable;" \
"name=vendorfs,size=16M;" \
"name=rootfs,size=746M;" \
"name=userfs,size=-\0"
#else
#define STM32MP_PARTS_DEFAULT
#endif
#define STM32MP_EXTRA \
"env_check=if env info -p -d -q; then env save; fi\0" \
"boot_net_usb_start=true\0"
#ifndef STM32MP_BOARD_EXTRA_ENV
#define STM32MP_BOARD_EXTRA_ENV
#endif
#include <config_distro_bootcmd.h>
stm32mp1: update memory layout Update the memory layout to be aligned with other platform and avoid overlap with 32MB Linux kernel (multiv7 image). + Kernel => 32MiB offset = 0xC2000000 and increase the bootm size to 32MiB + FDT => 64MiB offset = 0xc4000000 + SCRIPT => 65Mib offset = 0xc4100000 + PXESCRIPT => 66Mib offset = 0xc4200000 + SPLASHIMAGE => 67Mib offset = 0xc4300000 + RAMDISK => 68Mib offset = 0xc4400000 (not limited size) In sources/boot/u-boot/doc/README.distro + kernel_addr_r: A size of 16MB for the kernel is likely adequate. + pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate. + fdt_addr_r: A size of 1MB for the FDT/DTB seems reasonable. + ramdisk_addr_r: It is recommended that this location be highest in RAM out of fdt_addr_, kernel_addr_r, and ramdisk_addr_r, so that the RAM disk can vary in size and use any available RAM. + pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate. + scriptaddr: A size of 1MB for extlinux.conf is more than adequate. For suggestions on memory locations for ARM systems, you must follow the guidelines specified in Documentation/arm/Booting in the Linux kernel tree. And in sources/linux-stm32mp/Documentation/arm/Booting The zImage may also be placed in system RAM and called there. The kernel should be placed in the first 128MiB of RAM. It is recommended that it is loaded above 32MiB in order to avoid the need to relocate prior to decompression, which will make the boot process slightly faster. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-27 16:01:21 +00:00
/*
* memory layout for 32M uncompressed/compressed kernel,
* 1M fdt, 1M script, 1M pxe and 1M for overlay
stm32mp1: update memory layout Update the memory layout to be aligned with other platform and avoid overlap with 32MB Linux kernel (multiv7 image). + Kernel => 32MiB offset = 0xC2000000 and increase the bootm size to 32MiB + FDT => 64MiB offset = 0xc4000000 + SCRIPT => 65Mib offset = 0xc4100000 + PXESCRIPT => 66Mib offset = 0xc4200000 + SPLASHIMAGE => 67Mib offset = 0xc4300000 + RAMDISK => 68Mib offset = 0xc4400000 (not limited size) In sources/boot/u-boot/doc/README.distro + kernel_addr_r: A size of 16MB for the kernel is likely adequate. + pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate. + fdt_addr_r: A size of 1MB for the FDT/DTB seems reasonable. + ramdisk_addr_r: It is recommended that this location be highest in RAM out of fdt_addr_, kernel_addr_r, and ramdisk_addr_r, so that the RAM disk can vary in size and use any available RAM. + pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate. + scriptaddr: A size of 1MB for extlinux.conf is more than adequate. For suggestions on memory locations for ARM systems, you must follow the guidelines specified in Documentation/arm/Booting in the Linux kernel tree. And in sources/linux-stm32mp/Documentation/arm/Booting The zImage may also be placed in system RAM and called there. The kernel should be placed in the first 128MiB of RAM. It is recommended that it is loaded above 32MiB in order to avoid the need to relocate prior to decompression, which will make the boot process slightly faster. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-27 16:01:21 +00:00
* and the ramdisk at the end.
*/
#define __KERNEL_ADDR_R __stringify(0xc2000000)
#define __FDT_ADDR_R __stringify(0xc4000000)
#define __SCRIPT_ADDR_R __stringify(0xc4100000)
#define __PXEFILE_ADDR_R __stringify(0xc4200000)
#define __FDTOVERLAY_ADDR_R __stringify(0xc4300000)
#define __RAMDISK_ADDR_R __stringify(0xc4400000)
#define STM32MP_MEM_LAYOUT \
"kernel_addr_r=" __KERNEL_ADDR_R "\0" \
"fdt_addr_r=" __FDT_ADDR_R "\0" \
"scriptaddr=" __SCRIPT_ADDR_R "\0" \
"pxefile_addr_r=" __PXEFILE_ADDR_R "\0" \
"fdtoverlay_addr_r=" __FDTOVERLAY_ADDR_R "\0" \
"ramdisk_addr_r=" __RAMDISK_ADDR_R "\0"
#define CONFIG_EXTRA_ENV_SETTINGS \
STM32MP_MEM_LAYOUT \
STM32MP_BOOTCMD \
STM32MP_PARTS_DEFAULT \
BOOTENV \
STM32MP_EXTRA \
STM32MP_BOARD_EXTRA_ENV
#endif /* ifndef CONFIG_SPL_BUILD */
#endif /* ifdef CONFIG_DISTRO_DEFAULTS*/
#endif /* __CONFIG_STM32MP15_COMMMON_H */