u-boot/doc/device-tree-bindings/leds/leds-bcm6328.txt

LEDs connected to Broadcom BCM6328 controller

This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268.
In these SoCs it's possible to control LEDs both as GPIOs or by hardware.
However, on some devices there are Serial LEDs (LEDs connected to a 74x164
controller), which can either be controlled by software (exporting the 74x164
as spi-gpio. See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or
by hardware using this driver.
Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and
exporting the 74x164 as spi-gpio prevents those LEDs to be hardware
controlled, so the only chance to keep them working is by using this driver.

Required properties:
  - compatible : should be "brcm,bcm6328-leds".
  - #address-cells : must be 1.
  - #size-cells : must be 0.
  - reg : BCM6328 LED controller address and size.

Optional properties:
  - brcm,serial-leds : Boolean, enables Serial LEDs.
    Default : false
  - brcm,serial-mux : Boolean, enables Serial LEDs multiplexing.
    Default : false
  - brcm,serial-clk-low : Boolean, makes clock signal active low.
    Default : false
  - brcm,serial-dat-low : Boolean, makes data signal active low.
    Default : false
  - brcm,serial-shift-inv : Boolean, inverts Serial LEDs shift direction.
    Default : false

Each LED is represented as a sub-node of the brcm,bcm6328-leds device.

LED sub-node required properties:
  - reg : LED pin number (only LEDs 0 to 23 are valid).

LED sub-node optional properties:
  - label : see Documentation/devicetree/bindings/leds/common.txt
  - active-low : Boolean, makes LED active low.
    Default : false

Examples:
Scenario 1 : BCM6328 with 4 GPIO LEDs
	leds0: led-controller@10000800 {
		compatible = "brcm,bcm6328-leds";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0x10000800 0x24>;

		alarm_red@2 {
			reg = <2>;
			active-low;
			label = "red:alarm";
		};
		inet_green@3 {
			reg = <3>;
			active-low;
			label = "green:inet";
		};
		power_green@4 {
			reg = <4>;
			active-low;
			label = "green:power";
		};
	};

Scenario 2 : BCM63268 with Serial LEDs
	leds0: led-controller@10001900 {
		compatible = "brcm,bcm6328-leds";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0x10001900 0x24>;
		brcm,serial-leds;
		brcm,serial-dat-low;
		brcm,serial-shift-inv;

		inet_red@2 {
			reg = <2>;
			active-low;
			label = "red:inet";
		};
		dsl_green@3 {
			reg = <3>;
			active-low;
			label = "green:dsl";
		};
		usb_green@4 {
			reg = <4>;
			active-low;
			label = "green:usb";
		};
		wps_green@7 {
			reg = <7>;
			active-low;
			label = "green:wps";
		};
		inet_green@8 {
			reg = <8>;
			active-low;
			label = "green:inet";
		};
		power_green@20 {
			reg = <20>;
			active-low;
			label = "green:power";
		};
	};