u-boot/net/bootp.c

1030 lines
25 KiB
C
Raw Normal View History

2002-09-27 23:19:37 +00:00
/*
* Based on LiMon - BOOTP.
*
* Copyright 1994, 1995, 2000 Neil Russell.
* (See License)
* Copyright 2000 Roland Borde
* Copyright 2000 Paolo Scaffardi
* Copyright 2000-2004 Wolfgang Denk, wd@denx.de
2002-09-27 23:19:37 +00:00
*/
#include <common.h>
#include <command.h>
#include <net.h>
#include <net/tftp.h>
2002-09-27 23:19:37 +00:00
#include "bootp.h"
#include "nfs.h"
2002-09-27 23:19:37 +00:00
#ifdef CONFIG_STATUS_LED
#include <status_led.h>
#endif
#ifdef CONFIG_BOOTP_RANDOM_DELAY
#include "net_rand.h"
#endif
2002-09-27 23:19:37 +00:00
#define BOOTP_VENDOR_MAGIC 0x63825363 /* RFC1048 Magic Cookie */
2002-09-27 23:19:37 +00:00
net: BOOTP retry timeout improvements Currently, the BOOTP code sends out its initial request as soon as the Ethernet driver indicates "link up". If this packet is lost or not replied to for some reason, the code waits for a 1s timeout before retrying. For some reason, such early packets are often lost on my system, so this causes an annoying delay. To optimize this, modify the BOOTP code to have very short timeouts for the first packet transmitted, but gradually increase the timeout each time a timeout occurs. This way, if the first packet is lost, the second packet is transmitted quite quickly and hence the overall delay is low. However, if there's still no response, we don't keep spewing out packets at an insane speed. It's arguably more correct to try and find out why the first packet is lost. However, it seems to disappear inside my Ethenet chip; the TX chip indicates no error during TX (not that it has much in the way of reporting...), yet wireshark on the RX side doesn't see any packet. FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is reported too early or based on the wrong condition in HW, and we should add some fixed extra delay into the driver. However, this would slow down every link up event even if it ends up not being needed in some cases. Having BOOTP retry quickly applies the fix/WAR to every possible Ethernet device, and is quite simple to implement, so seems a better solution. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-07-25 23:30:48 +00:00
/*
* The timeout for the initial BOOTP/DHCP request used to be described by a
* counter of fixed-length timeout periods. TIMEOUT_COUNT represents
* that counter
*
* Now that the timeout periods are variable (exponential backoff and retry)
* we convert the timeout count to the absolute time it would have take to
* execute that many retries, and keep sending retry packets until that time
* is reached.
*/
#ifndef CONFIG_NET_RETRY_COUNT
# define TIMEOUT_COUNT 5 /* # of timeouts before giving up */
2002-09-27 23:19:37 +00:00
#else
# define TIMEOUT_COUNT (CONFIG_NET_RETRY_COUNT)
2002-09-27 23:19:37 +00:00
#endif
net: BOOTP retry timeout improvements Currently, the BOOTP code sends out its initial request as soon as the Ethernet driver indicates "link up". If this packet is lost or not replied to for some reason, the code waits for a 1s timeout before retrying. For some reason, such early packets are often lost on my system, so this causes an annoying delay. To optimize this, modify the BOOTP code to have very short timeouts for the first packet transmitted, but gradually increase the timeout each time a timeout occurs. This way, if the first packet is lost, the second packet is transmitted quite quickly and hence the overall delay is low. However, if there's still no response, we don't keep spewing out packets at an insane speed. It's arguably more correct to try and find out why the first packet is lost. However, it seems to disappear inside my Ethenet chip; the TX chip indicates no error during TX (not that it has much in the way of reporting...), yet wireshark on the RX side doesn't see any packet. FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is reported too early or based on the wrong condition in HW, and we should add some fixed extra delay into the driver. However, this would slow down every link up event even if it ends up not being needed in some cases. Having BOOTP retry quickly applies the fix/WAR to every possible Ethernet device, and is quite simple to implement, so seems a better solution. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-07-25 23:30:48 +00:00
#define TIMEOUT_MS ((3 + (TIMEOUT_COUNT * 5)) * 1000)
2002-09-27 23:19:37 +00:00
#define PORT_BOOTPS 67 /* BOOTP server UDP port */
#define PORT_BOOTPC 68 /* BOOTP client UDP port */
2002-09-27 23:19:37 +00:00
#ifndef CONFIG_DHCP_MIN_EXT_LEN /* minimal length of extension list */
#define CONFIG_DHCP_MIN_EXT_LEN 64
2002-09-27 23:19:37 +00:00
#endif
net: More BOOTP retry timeout improvements It's not unusual for DHCP servers to take a couple hundred milliseconds to respond to DHCP discover messages. One possible reason for the delay can be that the server checks (typically using an ARP request) that the IP it's about to hand out isn't in use yet. To make matters worse, some servers may also queue up requests and process them sequentially, which can cause excessively long delays if clients retry too fast. Commit f59be6e850b3 ("net: BOOTP retry timeout improvements") shortened the retry timeouts significantly, but the BOOTP/DHCP implementation in U-Boot doesn't handle that well because it will ignore incoming replies to earlier requests. In one particular setup this increases the time it takes to obtain a DHCP lease from 630 ms to 8313 ms. This commit attempts to fix this in two ways. First it increases the initial retry timeout from 10 ms to 250 ms to give DHCP servers some more time to respond. At the same time a cache of outstanding DHCP request IDs is kept so that the implementation will know to continue transactions even after a retransmission of the DISCOVER message. The maximum retry timeout is also increased from 1 second to 2 seconds. An ID cache of size 4 will keep DHCP requests around for 8 seconds (once the maximum retry timeout has been reached) before dropping them. This should give servers plenty of time to respond. If it ever turns out that this isn't enough, the size of the cache can easily be increased. With this commit the DHCP lease on the above-mentioned setup still takes longer (1230 ms) than originally, but that's an acceptable compromise to improve DHCP lease acquisition time for a broader range of setups. To make it easier to benchmark DHCP in the future, this commit also adds the time it took to obtain a lease to the final "DHCP client bound to address x.x.x.x" message. Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-19 08:21:24 +00:00
#ifndef CONFIG_BOOTP_ID_CACHE_SIZE
#define CONFIG_BOOTP_ID_CACHE_SIZE 4
#endif
u32 bootp_ids[CONFIG_BOOTP_ID_CACHE_SIZE];
net: More BOOTP retry timeout improvements It's not unusual for DHCP servers to take a couple hundred milliseconds to respond to DHCP discover messages. One possible reason for the delay can be that the server checks (typically using an ARP request) that the IP it's about to hand out isn't in use yet. To make matters worse, some servers may also queue up requests and process them sequentially, which can cause excessively long delays if clients retry too fast. Commit f59be6e850b3 ("net: BOOTP retry timeout improvements") shortened the retry timeouts significantly, but the BOOTP/DHCP implementation in U-Boot doesn't handle that well because it will ignore incoming replies to earlier requests. In one particular setup this increases the time it takes to obtain a DHCP lease from 630 ms to 8313 ms. This commit attempts to fix this in two ways. First it increases the initial retry timeout from 10 ms to 250 ms to give DHCP servers some more time to respond. At the same time a cache of outstanding DHCP request IDs is kept so that the implementation will know to continue transactions even after a retransmission of the DISCOVER message. The maximum retry timeout is also increased from 1 second to 2 seconds. An ID cache of size 4 will keep DHCP requests around for 8 seconds (once the maximum retry timeout has been reached) before dropping them. This should give servers plenty of time to respond. If it ever turns out that this isn't enough, the size of the cache can easily be increased. With this commit the DHCP lease on the above-mentioned setup still takes longer (1230 ms) than originally, but that's an acceptable compromise to improve DHCP lease acquisition time for a broader range of setups. To make it easier to benchmark DHCP in the future, this commit also adds the time it took to obtain a lease to the final "DHCP client bound to address x.x.x.x" message. Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-19 08:21:24 +00:00
unsigned int bootp_num_ids;
int bootp_try;
net: BOOTP retry timeout improvements Currently, the BOOTP code sends out its initial request as soon as the Ethernet driver indicates "link up". If this packet is lost or not replied to for some reason, the code waits for a 1s timeout before retrying. For some reason, such early packets are often lost on my system, so this causes an annoying delay. To optimize this, modify the BOOTP code to have very short timeouts for the first packet transmitted, but gradually increase the timeout each time a timeout occurs. This way, if the first packet is lost, the second packet is transmitted quite quickly and hence the overall delay is low. However, if there's still no response, we don't keep spewing out packets at an insane speed. It's arguably more correct to try and find out why the first packet is lost. However, it seems to disappear inside my Ethenet chip; the TX chip indicates no error during TX (not that it has much in the way of reporting...), yet wireshark on the RX side doesn't see any packet. FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is reported too early or based on the wrong condition in HW, and we should add some fixed extra delay into the driver. However, this would slow down every link up event even if it ends up not being needed in some cases. Having BOOTP retry quickly applies the fix/WAR to every possible Ethernet device, and is quite simple to implement, so seems a better solution. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-07-25 23:30:48 +00:00
ulong bootp_start;
ulong bootp_timeout;
char net_nis_domain[32] = {0,}; /* Our NIS domain */
char net_hostname[32] = {0,}; /* Our hostname */
char net_root_path[64] = {0,}; /* Our bootpath */
2002-09-27 23:19:37 +00:00
#if defined(CONFIG_CMD_DHCP)
2012-10-29 13:34:33 +00:00
static dhcp_state_t dhcp_state = INIT;
static u32 dhcp_leasetime;
static struct in_addr dhcp_server_ip;
static void dhcp_handler(uchar *pkt, unsigned dest, struct in_addr sip,
unsigned src, unsigned len);
2002-09-27 23:19:37 +00:00
/* For Debug */
#if 0
static char *dhcpmsg2str(int type)
2002-09-27 23:19:37 +00:00
{
switch (type) {
case 1: return "DHCPDISCOVER"; break;
case 2: return "DHCPOFFER"; break;
case 3: return "DHCPREQUEST"; break;
case 4: return "DHCPDECLINE"; break;
case 5: return "DHCPACK"; break;
case 6: return "DHCPNACK"; break;
case 7: return "DHCPRELEASE"; break;
2002-09-27 23:19:37 +00:00
default: return "UNKNOWN/INVALID MSG TYPE"; break;
}
}
#endif
#endif
2002-09-27 23:19:37 +00:00
net: More BOOTP retry timeout improvements It's not unusual for DHCP servers to take a couple hundred milliseconds to respond to DHCP discover messages. One possible reason for the delay can be that the server checks (typically using an ARP request) that the IP it's about to hand out isn't in use yet. To make matters worse, some servers may also queue up requests and process them sequentially, which can cause excessively long delays if clients retry too fast. Commit f59be6e850b3 ("net: BOOTP retry timeout improvements") shortened the retry timeouts significantly, but the BOOTP/DHCP implementation in U-Boot doesn't handle that well because it will ignore incoming replies to earlier requests. In one particular setup this increases the time it takes to obtain a DHCP lease from 630 ms to 8313 ms. This commit attempts to fix this in two ways. First it increases the initial retry timeout from 10 ms to 250 ms to give DHCP servers some more time to respond. At the same time a cache of outstanding DHCP request IDs is kept so that the implementation will know to continue transactions even after a retransmission of the DISCOVER message. The maximum retry timeout is also increased from 1 second to 2 seconds. An ID cache of size 4 will keep DHCP requests around for 8 seconds (once the maximum retry timeout has been reached) before dropping them. This should give servers plenty of time to respond. If it ever turns out that this isn't enough, the size of the cache can easily be increased. With this commit the DHCP lease on the above-mentioned setup still takes longer (1230 ms) than originally, but that's an acceptable compromise to improve DHCP lease acquisition time for a broader range of setups. To make it easier to benchmark DHCP in the future, this commit also adds the time it took to obtain a lease to the final "DHCP client bound to address x.x.x.x" message. Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-19 08:21:24 +00:00
static void bootp_add_id(ulong id)
{
if (bootp_num_ids >= ARRAY_SIZE(bootp_ids)) {
size_t size = sizeof(bootp_ids) - sizeof(id);
memmove(bootp_ids, &bootp_ids[1], size);
bootp_ids[bootp_num_ids - 1] = id;
} else {
bootp_ids[bootp_num_ids] = id;
bootp_num_ids++;
}
}
static bool bootp_match_id(ulong id)
{
unsigned int i;
for (i = 0; i < bootp_num_ids; i++)
if (bootp_ids[i] == id)
return true;
return false;
}
static int check_packet(uchar *pkt, unsigned dest, unsigned src, unsigned len)
2002-09-27 23:19:37 +00:00
{
struct bootp_hdr *bp = (struct bootp_hdr *)pkt;
2002-09-27 23:19:37 +00:00
int retval = 0;
if (dest != PORT_BOOTPC || src != PORT_BOOTPS)
retval = -1;
else if (len < sizeof(struct bootp_hdr) - OPT_FIELD_SIZE)
2002-09-27 23:19:37 +00:00
retval = -2;
else if (bp->bp_op != OP_BOOTREQUEST &&
bp->bp_op != OP_BOOTREPLY &&
bp->bp_op != DHCP_OFFER &&
bp->bp_op != DHCP_ACK &&
bp->bp_op != DHCP_NAK)
2002-09-27 23:19:37 +00:00
retval = -3;
else if (bp->bp_htype != HWT_ETHER)
retval = -4;
else if (bp->bp_hlen != HWL_ETHER)
retval = -5;
else if (!bootp_match_id(net_read_u32(&bp->bp_id)))
2002-09-27 23:19:37 +00:00
retval = -6;
debug("Filtering pkt = %d\n", retval);
2002-09-27 23:19:37 +00:00
return retval;
}
/*
* Copy parameters of interest from BOOTP_REPLY/DHCP_OFFER packet
*/
static void store_net_params(struct bootp_hdr *bp)
2002-09-27 23:19:37 +00:00
{
#if !defined(CONFIG_BOOTP_SERVERIP)
struct in_addr tmp_ip;
net_copy_ip(&tmp_ip, &bp->bp_siaddr);
if (tmp_ip.s_addr != 0)
net_copy_ip(&net_server_ip, &bp->bp_siaddr);
memcpy(net_server_ethaddr,
((struct ethernet_hdr *)net_rx_packet)->et_src, 6);
if (strlen(bp->bp_file) > 0)
copy_filename(net_boot_file_name, bp->bp_file,
sizeof(net_boot_file_name));
2002-09-27 23:19:37 +00:00
debug("net_boot_file_name: %s\n", net_boot_file_name);
2002-09-27 23:19:37 +00:00
/* Propagate to environment:
* don't delete exising entry when BOOTP / DHCP reply does
2002-09-27 23:19:37 +00:00
* not contain a new value
*/
if (*net_boot_file_name)
setenv("bootfile", net_boot_file_name);
#endif
net_copy_ip(&net_ip, &bp->bp_yiaddr);
2002-09-27 23:19:37 +00:00
}
static int truncate_sz(const char *name, int maxlen, int curlen)
2002-09-27 23:19:37 +00:00
{
if (curlen >= maxlen) {
printf("*** WARNING: %s is too long (%d - max: %d)"
" - truncated\n", name, curlen, maxlen);
2002-09-27 23:19:37 +00:00
curlen = maxlen - 1;
}
return curlen;
2002-09-27 23:19:37 +00:00
}
#if !defined(CONFIG_CMD_DHCP)
2002-09-27 23:19:37 +00:00
static void bootp_process_vendor_field(u8 *ext)
2002-09-27 23:19:37 +00:00
{
int size = *(ext + 1);
2002-09-27 23:19:37 +00:00
debug("[BOOTP] Processing extension %d... (%d bytes)\n", *ext,
*(ext + 1));
2002-09-27 23:19:37 +00:00
net_boot_file_expected_size_in_blocks = 0;
2002-09-27 23:19:37 +00:00
switch (*ext) {
/* Fixed length fields */
case 1: /* Subnet mask */
if (net_netmask.s_addr == 0)
net_copy_ip(&net_netmask, (struct in_addr *)(ext + 2));
2002-09-27 23:19:37 +00:00
break;
case 2: /* Time offset - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
/* Variable length fields */
case 3: /* Gateways list */
if (net_gateway.s_addr == 0)
net_copy_ip(&net_gateway, (struct in_addr *)(ext + 2));
2002-09-27 23:19:37 +00:00
break;
case 4: /* Time server - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
case 5: /* IEN-116 name server - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
case 6:
if (net_dns_server.s_addr == 0)
net_copy_ip(&net_dns_server,
(struct in_addr *)(ext + 2));
#if defined(CONFIG_BOOTP_DNS2)
if ((net_dns_server2.s_addr == 0) && (size > 4))
net_copy_ip(&net_dns_server2,
(struct in_addr *)(ext + 2 + 4));
#endif
2002-09-27 23:19:37 +00:00
break;
case 7: /* Log server - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
case 8: /* Cookie/Quote server - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
case 9: /* LPR server - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
case 10: /* Impress server - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
case 11: /* RPL server - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
case 12: /* Host name */
if (net_hostname[0] == 0) {
size = truncate_sz("Host Name",
sizeof(net_hostname), size);
memcpy(&net_hostname, ext + 2, size);
net_hostname[size] = 0;
2002-09-27 23:19:37 +00:00
}
break;
case 13: /* Boot file size */
2002-09-27 23:19:37 +00:00
if (size == 2)
net_boot_file_expected_size_in_blocks =
ntohs(*(ushort *)(ext + 2));
2002-09-27 23:19:37 +00:00
else if (size == 4)
net_boot_file_expected_size_in_blocks =
ntohl(*(ulong *)(ext + 2));
2002-09-27 23:19:37 +00:00
break;
case 14: /* Merit dump file - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
case 15: /* Domain name - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
case 16: /* Swap server - Not yet supported */
2002-09-27 23:19:37 +00:00
break;
case 17: /* Root path */
if (net_root_path[0] == 0) {
size = truncate_sz("Root Path",
sizeof(net_root_path), size);
memcpy(&net_root_path, ext + 2, size);
net_root_path[size] = 0;
2002-09-27 23:19:37 +00:00
}
break;
case 18: /* Extension path - Not yet supported */
2002-09-27 23:19:37 +00:00
/*
* This can be used to send the information of the
* vendor area in another file that the client can
* access via TFTP.
2002-09-27 23:19:37 +00:00
*/
break;
/* IP host layer fields */
case 40: /* NIS Domain name */
if (net_nis_domain[0] == 0) {
size = truncate_sz("NIS Domain Name",
sizeof(net_nis_domain), size);
memcpy(&net_nis_domain, ext + 2, size);
net_nis_domain[size] = 0;
2002-09-27 23:19:37 +00:00
}
break;
#if defined(CONFIG_CMD_SNTP) && defined(CONFIG_BOOTP_NTPSERVER)
case 42: /* NTP server IP */
net_copy_ip(&net_ntp_server, (struct in_addr *)(ext + 2));
break;
#endif
/* Application layer fields */
case 43: /* Vendor specific info - Not yet supported */
2002-09-27 23:19:37 +00:00
/*
* Binary information to exchange specific
* product information.
2002-09-27 23:19:37 +00:00
*/
break;
/* Reserved (custom) fields (128..254) */
}
2002-09-27 23:19:37 +00:00
}
static void bootp_process_vendor(u8 *ext, int size)
2002-09-27 23:19:37 +00:00
{
u8 *end = ext + size;
2002-09-27 23:19:37 +00:00
debug("[BOOTP] Checking extension (%d bytes)...\n", size);
2002-09-27 23:19:37 +00:00
while ((ext < end) && (*ext != 0xff)) {
if (*ext == 0) {
ext++;
} else {
u8 *opt = ext;
ext += ext[1] + 2;
if (ext <= end)
bootp_process_vendor_field(opt);
}
2002-09-27 23:19:37 +00:00
}
debug("[BOOTP] Received fields:\n");
if (net_netmask.s_addr)
debug("net_netmask : %pI4\n", &net_netmask);
if (net_gateway.s_addr)
debug("net_gateway : %pI4", &net_gateway);
if (net_boot_file_expected_size_in_blocks)
debug("net_boot_file_expected_size_in_blocks : %d\n",
net_boot_file_expected_size_in_blocks);
2002-09-27 23:19:37 +00:00
if (net_hostname[0])
debug("net_hostname : %s\n", net_hostname);
if (net_root_path[0])
debug("net_root_path : %s\n", net_root_path);
if (net_nis_domain[0])
debug("net_nis_domain : %s\n", net_nis_domain);
#if defined(CONFIG_CMD_SNTP) && defined(CONFIG_BOOTP_NTPSERVER)
if (net_ntp_server)
debug("net_ntp_server : %pI4\n", &net_ntp_server);
#endif
}
2002-09-27 23:19:37 +00:00
/*
* Handle a BOOTP received packet.
*/
static void bootp_handler(uchar *pkt, unsigned dest, struct in_addr sip,
unsigned src, unsigned len)
2002-09-27 23:19:37 +00:00
{
struct bootp_hdr *bp;
2002-09-27 23:19:37 +00:00
debug("got BOOTP packet (src=%d, dst=%d, len=%d want_len=%zu)\n",
src, dest, len, sizeof(struct bootp_hdr));
2002-09-27 23:19:37 +00:00
bp = (struct bootp_hdr *)pkt;
2002-09-27 23:19:37 +00:00
/* Filter out pkts we don't want */
if (check_packet(pkt, dest, src, len))
2002-09-27 23:19:37 +00:00
return;
/*
* Got a good BOOTP reply. Copy the data into our variables.
2002-09-27 23:19:37 +00:00
*/
#ifdef CONFIG_STATUS_LED
status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF);
2002-09-27 23:19:37 +00:00
#endif
store_net_params(bp); /* Store net parameters from reply */
2002-09-27 23:19:37 +00:00
/* Retrieve extended information (we must parse the vendor area) */
if (net_read_u32((u32 *)&bp->bp_vend[0]) == htonl(BOOTP_VENDOR_MAGIC))
bootp_process_vendor((uchar *)&bp->bp_vend[4], len);
2002-09-27 23:19:37 +00:00
net_set_timeout_handler(0, (thand_f *)0);
bootstage_mark_name(BOOTSTAGE_ID_BOOTP_STOP, "bootp_stop");
2002-09-27 23:19:37 +00:00
debug("Got good BOOTP\n");
2002-09-27 23:19:37 +00:00
net_auto_load();
2002-09-27 23:19:37 +00:00
}
#endif
2002-09-27 23:19:37 +00:00
/*
* Timeout on BOOTP/DHCP request.
*/
static void bootp_timeout_handler(void)
2002-09-27 23:19:37 +00:00
{
net: BOOTP retry timeout improvements Currently, the BOOTP code sends out its initial request as soon as the Ethernet driver indicates "link up". If this packet is lost or not replied to for some reason, the code waits for a 1s timeout before retrying. For some reason, such early packets are often lost on my system, so this causes an annoying delay. To optimize this, modify the BOOTP code to have very short timeouts for the first packet transmitted, but gradually increase the timeout each time a timeout occurs. This way, if the first packet is lost, the second packet is transmitted quite quickly and hence the overall delay is low. However, if there's still no response, we don't keep spewing out packets at an insane speed. It's arguably more correct to try and find out why the first packet is lost. However, it seems to disappear inside my Ethenet chip; the TX chip indicates no error during TX (not that it has much in the way of reporting...), yet wireshark on the RX side doesn't see any packet. FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is reported too early or based on the wrong condition in HW, and we should add some fixed extra delay into the driver. However, this would slow down every link up event even if it ends up not being needed in some cases. Having BOOTP retry quickly applies the fix/WAR to every possible Ethernet device, and is quite simple to implement, so seems a better solution. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-07-25 23:30:48 +00:00
ulong time_taken = get_timer(bootp_start);
if (time_taken >= TIMEOUT_MS) {
#ifdef CONFIG_BOOTP_MAY_FAIL
net: BOOTP retry timeout improvements Currently, the BOOTP code sends out its initial request as soon as the Ethernet driver indicates "link up". If this packet is lost or not replied to for some reason, the code waits for a 1s timeout before retrying. For some reason, such early packets are often lost on my system, so this causes an annoying delay. To optimize this, modify the BOOTP code to have very short timeouts for the first packet transmitted, but gradually increase the timeout each time a timeout occurs. This way, if the first packet is lost, the second packet is transmitted quite quickly and hence the overall delay is low. However, if there's still no response, we don't keep spewing out packets at an insane speed. It's arguably more correct to try and find out why the first packet is lost. However, it seems to disappear inside my Ethenet chip; the TX chip indicates no error during TX (not that it has much in the way of reporting...), yet wireshark on the RX side doesn't see any packet. FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is reported too early or based on the wrong condition in HW, and we should add some fixed extra delay into the driver. However, this would slow down every link up event even if it ends up not being needed in some cases. Having BOOTP retry quickly applies the fix/WAR to every possible Ethernet device, and is quite simple to implement, so seems a better solution. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-07-25 23:30:48 +00:00
puts("\nRetry time exceeded\n");
net_set_state(NETLOOP_FAIL);
#else
net: BOOTP retry timeout improvements Currently, the BOOTP code sends out its initial request as soon as the Ethernet driver indicates "link up". If this packet is lost or not replied to for some reason, the code waits for a 1s timeout before retrying. For some reason, such early packets are often lost on my system, so this causes an annoying delay. To optimize this, modify the BOOTP code to have very short timeouts for the first packet transmitted, but gradually increase the timeout each time a timeout occurs. This way, if the first packet is lost, the second packet is transmitted quite quickly and hence the overall delay is low. However, if there's still no response, we don't keep spewing out packets at an insane speed. It's arguably more correct to try and find out why the first packet is lost. However, it seems to disappear inside my Ethenet chip; the TX chip indicates no error during TX (not that it has much in the way of reporting...), yet wireshark on the RX side doesn't see any packet. FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is reported too early or based on the wrong condition in HW, and we should add some fixed extra delay into the driver. However, this would slow down every link up event even if it ends up not being needed in some cases. Having BOOTP retry quickly applies the fix/WAR to every possible Ethernet device, and is quite simple to implement, so seems a better solution. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-07-25 23:30:48 +00:00
puts("\nRetry time exceeded; starting again\n");
net_start_again();
#endif
2002-09-27 23:19:37 +00:00
} else {
net: BOOTP retry timeout improvements Currently, the BOOTP code sends out its initial request as soon as the Ethernet driver indicates "link up". If this packet is lost or not replied to for some reason, the code waits for a 1s timeout before retrying. For some reason, such early packets are often lost on my system, so this causes an annoying delay. To optimize this, modify the BOOTP code to have very short timeouts for the first packet transmitted, but gradually increase the timeout each time a timeout occurs. This way, if the first packet is lost, the second packet is transmitted quite quickly and hence the overall delay is low. However, if there's still no response, we don't keep spewing out packets at an insane speed. It's arguably more correct to try and find out why the first packet is lost. However, it seems to disappear inside my Ethenet chip; the TX chip indicates no error during TX (not that it has much in the way of reporting...), yet wireshark on the RX side doesn't see any packet. FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is reported too early or based on the wrong condition in HW, and we should add some fixed extra delay into the driver. However, this would slow down every link up event even if it ends up not being needed in some cases. Having BOOTP retry quickly applies the fix/WAR to every possible Ethernet device, and is quite simple to implement, so seems a better solution. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-07-25 23:30:48 +00:00
bootp_timeout *= 2;
net: More BOOTP retry timeout improvements It's not unusual for DHCP servers to take a couple hundred milliseconds to respond to DHCP discover messages. One possible reason for the delay can be that the server checks (typically using an ARP request) that the IP it's about to hand out isn't in use yet. To make matters worse, some servers may also queue up requests and process them sequentially, which can cause excessively long delays if clients retry too fast. Commit f59be6e850b3 ("net: BOOTP retry timeout improvements") shortened the retry timeouts significantly, but the BOOTP/DHCP implementation in U-Boot doesn't handle that well because it will ignore incoming replies to earlier requests. In one particular setup this increases the time it takes to obtain a DHCP lease from 630 ms to 8313 ms. This commit attempts to fix this in two ways. First it increases the initial retry timeout from 10 ms to 250 ms to give DHCP servers some more time to respond. At the same time a cache of outstanding DHCP request IDs is kept so that the implementation will know to continue transactions even after a retransmission of the DISCOVER message. The maximum retry timeout is also increased from 1 second to 2 seconds. An ID cache of size 4 will keep DHCP requests around for 8 seconds (once the maximum retry timeout has been reached) before dropping them. This should give servers plenty of time to respond. If it ever turns out that this isn't enough, the size of the cache can easily be increased. With this commit the DHCP lease on the above-mentioned setup still takes longer (1230 ms) than originally, but that's an acceptable compromise to improve DHCP lease acquisition time for a broader range of setups. To make it easier to benchmark DHCP in the future, this commit also adds the time it took to obtain a lease to the final "DHCP client bound to address x.x.x.x" message. Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-19 08:21:24 +00:00
if (bootp_timeout > 2000)
bootp_timeout = 2000;
net_set_timeout_handler(bootp_timeout, bootp_timeout_handler);
bootp_request();
2002-09-27 23:19:37 +00:00
}
}
#define put_vci(e, str) \
do { \
size_t vci_strlen = strlen(str); \
*e++ = 60; /* Vendor Class Identifier */ \
*e++ = vci_strlen; \
memcpy(e, str, vci_strlen); \
e += vci_strlen; \
} while (0)
2002-09-27 23:19:37 +00:00
/*
* Initialize BOOTP extension fields in the request.
*/
#if defined(CONFIG_CMD_DHCP)
static int dhcp_extended(u8 *e, int message_type, struct in_addr server_ip,
struct in_addr requested_ip)
2002-09-27 23:19:37 +00:00
{
u8 *start = e;
u8 *cnt;
#if defined(CONFIG_BOOTP_PXE)
char *uuid;
u16 clientarch;
#endif
#if defined(CONFIG_BOOTP_VENDOREX)
u8 *x;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_SEND_HOSTNAME)
2005-10-13 14:45:02 +00:00
char *hostname;
#endif
2002-09-27 23:19:37 +00:00
*e++ = 99; /* RFC1048 Magic Cookie */
*e++ = 130;
*e++ = 83;
*e++ = 99;
2002-09-27 23:19:37 +00:00
*e++ = 53; /* DHCP Message Type */
*e++ = 1;
*e++ = message_type;
2002-09-27 23:19:37 +00:00
*e++ = 57; /* Maximum DHCP Message Size */
*e++ = 2;
*e++ = (576 - 312 + OPT_FIELD_SIZE) >> 8;
*e++ = (576 - 312 + OPT_FIELD_SIZE) & 0xff;
2002-09-27 23:19:37 +00:00
if (server_ip.s_addr) {
int tmp = ntohl(server_ip.s_addr);
2002-09-27 23:19:37 +00:00
*e++ = 54; /* ServerID */
*e++ = 4;
*e++ = tmp >> 24;
*e++ = tmp >> 16;
*e++ = tmp >> 8;
*e++ = tmp & 0xff;
}
2002-09-27 23:19:37 +00:00
if (requested_ip.s_addr) {
int tmp = ntohl(requested_ip.s_addr);
2002-09-27 23:19:37 +00:00
*e++ = 50; /* Requested IP */
*e++ = 4;
*e++ = tmp >> 24;
*e++ = tmp >> 16;
*e++ = tmp >> 8;
*e++ = tmp & 0xff;
}
#if defined(CONFIG_BOOTP_SEND_HOSTNAME)
hostname = getenv("hostname");
if (hostname) {
int hostnamelen = strlen(hostname);
*e++ = 12; /* Hostname */
*e++ = hostnamelen;
memcpy(e, hostname, hostnamelen);
e += hostnamelen;
}
#endif
#if defined(CONFIG_BOOTP_PXE)
clientarch = CONFIG_BOOTP_PXE_CLIENTARCH;
*e++ = 93; /* Client System Architecture */
*e++ = 2;
*e++ = (clientarch >> 8) & 0xff;
*e++ = clientarch & 0xff;
*e++ = 94; /* Client Network Interface Identifier */
*e++ = 3;
*e++ = 1; /* type field for UNDI */
*e++ = 0; /* major revision */
*e++ = 0; /* minor revision */
uuid = getenv("pxeuuid");
if (uuid) {
if (uuid_str_valid(uuid)) {
*e++ = 97; /* Client Machine Identifier */
*e++ = 17;
*e++ = 0; /* type 0 - UUID */
uuid_str_to_bin(uuid, e, UUID_STR_FORMAT_STD);
e += 16;
} else {
printf("Invalid pxeuuid: %s\n", uuid);
}
}
#endif
#ifdef CONFIG_BOOTP_VCI_STRING
put_vci(e, CONFIG_BOOTP_VCI_STRING);
#endif
#if defined(CONFIG_BOOTP_VENDOREX)
x = dhcp_vendorex_prep(e);
if (x)
return x - start;
2002-09-27 23:19:37 +00:00
#endif
*e++ = 55; /* Parameter Request List */
cnt = e++; /* Pointer to count of requested items */
*cnt = 0;
#if defined(CONFIG_BOOTP_SUBNETMASK)
*e++ = 1; /* Subnet Mask */
*cnt += 1;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_TIMEOFFSET)
*e++ = 2;
*cnt += 1;
#endif
#if defined(CONFIG_BOOTP_GATEWAY)
*e++ = 3; /* Router Option */
*cnt += 1;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_DNS)
*e++ = 6; /* DNS Server(s) */
*cnt += 1;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_HOSTNAME)
*e++ = 12; /* Hostname */
*cnt += 1;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_BOOTFILESIZE)
*e++ = 13; /* Boot File Size */
*cnt += 1;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_BOOTPATH)
*e++ = 17; /* Boot path */
*cnt += 1;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_NISDOMAIN)
*e++ = 40; /* NIS Domain name request */
*cnt += 1;
#endif
#if defined(CONFIG_BOOTP_NTPSERVER)
*e++ = 42;
*cnt += 1;
2002-09-27 23:19:37 +00:00
#endif
/* no options, so back up to avoid sending an empty request list */
if (*cnt == 0)
e -= 2;
*e++ = 255; /* End of the list */
2002-09-27 23:19:37 +00:00
/* Pad to minimal length */
2002-09-27 23:19:37 +00:00
#ifdef CONFIG_DHCP_MIN_EXT_LEN
while ((e - start) < CONFIG_DHCP_MIN_EXT_LEN)
*e++ = 0;
2002-09-27 23:19:37 +00:00
#endif
return e - start;
2002-09-27 23:19:37 +00:00
}
#else
2002-09-27 23:19:37 +00:00
/*
* Warning: no field size check - change CONFIG_BOOTP_* at your own risk!
2002-09-27 23:19:37 +00:00
*/
static int bootp_extended(u8 *e)
2002-09-27 23:19:37 +00:00
{
u8 *start = e;
2002-09-27 23:19:37 +00:00
*e++ = 99; /* RFC1048 Magic Cookie */
*e++ = 130;
*e++ = 83;
*e++ = 99;
2002-09-27 23:19:37 +00:00
#if defined(CONFIG_CMD_DHCP)
*e++ = 53; /* DHCP Message Type */
*e++ = 1;
*e++ = DHCP_DISCOVER;
*e++ = 57; /* Maximum DHCP Message Size */
*e++ = 2;
*e++ = (576 - 312 + OPT_FIELD_SIZE) >> 16;
*e++ = (576 - 312 + OPT_FIELD_SIZE) & 0xff;
#endif
2002-09-27 23:19:37 +00:00
#if defined(CONFIG_BOOTP_VCI_STRING) || \
(defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_NET_VCI_STRING))
#ifdef CONFIG_SPL_BUILD
put_vci(e, CONFIG_SPL_NET_VCI_STRING);
#else
put_vci(e, CONFIG_BOOTP_VCI_STRING);
#endif
#endif
#if defined(CONFIG_BOOTP_SUBNETMASK)
*e++ = 1; /* Subnet mask request */
*e++ = 4;
e += 4;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_GATEWAY)
*e++ = 3; /* Default gateway request */
*e++ = 4;
e += 4;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_DNS)
*e++ = 6; /* Domain Name Server */
*e++ = 4;
e += 4;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_HOSTNAME)
*e++ = 12; /* Host name request */
*e++ = 32;
e += 32;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_BOOTFILESIZE)
*e++ = 13; /* Boot file size */
*e++ = 2;
e += 2;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_BOOTPATH)
*e++ = 17; /* Boot path */
*e++ = 32;
e += 32;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_NISDOMAIN)
*e++ = 40; /* NIS Domain name request */
*e++ = 32;
e += 32;
2002-09-27 23:19:37 +00:00
#endif
#if defined(CONFIG_BOOTP_NTPSERVER)
*e++ = 42;
*e++ = 4;
e += 4;
#endif
2002-09-27 23:19:37 +00:00
*e++ = 255; /* End of the list */
2002-09-27 23:19:37 +00:00
return e - start;
2002-09-27 23:19:37 +00:00
}
#endif
2002-09-27 23:19:37 +00:00
void bootp_reset(void)
net: BOOTP retry timeout improvements Currently, the BOOTP code sends out its initial request as soon as the Ethernet driver indicates "link up". If this packet is lost or not replied to for some reason, the code waits for a 1s timeout before retrying. For some reason, such early packets are often lost on my system, so this causes an annoying delay. To optimize this, modify the BOOTP code to have very short timeouts for the first packet transmitted, but gradually increase the timeout each time a timeout occurs. This way, if the first packet is lost, the second packet is transmitted quite quickly and hence the overall delay is low. However, if there's still no response, we don't keep spewing out packets at an insane speed. It's arguably more correct to try and find out why the first packet is lost. However, it seems to disappear inside my Ethenet chip; the TX chip indicates no error during TX (not that it has much in the way of reporting...), yet wireshark on the RX side doesn't see any packet. FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is reported too early or based on the wrong condition in HW, and we should add some fixed extra delay into the driver. However, this would slow down every link up event even if it ends up not being needed in some cases. Having BOOTP retry quickly applies the fix/WAR to every possible Ethernet device, and is quite simple to implement, so seems a better solution. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-07-25 23:30:48 +00:00
{
net: More BOOTP retry timeout improvements It's not unusual for DHCP servers to take a couple hundred milliseconds to respond to DHCP discover messages. One possible reason for the delay can be that the server checks (typically using an ARP request) that the IP it's about to hand out isn't in use yet. To make matters worse, some servers may also queue up requests and process them sequentially, which can cause excessively long delays if clients retry too fast. Commit f59be6e850b3 ("net: BOOTP retry timeout improvements") shortened the retry timeouts significantly, but the BOOTP/DHCP implementation in U-Boot doesn't handle that well because it will ignore incoming replies to earlier requests. In one particular setup this increases the time it takes to obtain a DHCP lease from 630 ms to 8313 ms. This commit attempts to fix this in two ways. First it increases the initial retry timeout from 10 ms to 250 ms to give DHCP servers some more time to respond. At the same time a cache of outstanding DHCP request IDs is kept so that the implementation will know to continue transactions even after a retransmission of the DISCOVER message. The maximum retry timeout is also increased from 1 second to 2 seconds. An ID cache of size 4 will keep DHCP requests around for 8 seconds (once the maximum retry timeout has been reached) before dropping them. This should give servers plenty of time to respond. If it ever turns out that this isn't enough, the size of the cache can easily be increased. With this commit the DHCP lease on the above-mentioned setup still takes longer (1230 ms) than originally, but that's an acceptable compromise to improve DHCP lease acquisition time for a broader range of setups. To make it easier to benchmark DHCP in the future, this commit also adds the time it took to obtain a lease to the final "DHCP client bound to address x.x.x.x" message. Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-19 08:21:24 +00:00
bootp_num_ids = 0;
bootp_try = 0;
net: BOOTP retry timeout improvements Currently, the BOOTP code sends out its initial request as soon as the Ethernet driver indicates "link up". If this packet is lost or not replied to for some reason, the code waits for a 1s timeout before retrying. For some reason, such early packets are often lost on my system, so this causes an annoying delay. To optimize this, modify the BOOTP code to have very short timeouts for the first packet transmitted, but gradually increase the timeout each time a timeout occurs. This way, if the first packet is lost, the second packet is transmitted quite quickly and hence the overall delay is low. However, if there's still no response, we don't keep spewing out packets at an insane speed. It's arguably more correct to try and find out why the first packet is lost. However, it seems to disappear inside my Ethenet chip; the TX chip indicates no error during TX (not that it has much in the way of reporting...), yet wireshark on the RX side doesn't see any packet. FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is reported too early or based on the wrong condition in HW, and we should add some fixed extra delay into the driver. However, this would slow down every link up event even if it ends up not being needed in some cases. Having BOOTP retry quickly applies the fix/WAR to every possible Ethernet device, and is quite simple to implement, so seems a better solution. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-07-25 23:30:48 +00:00
bootp_start = get_timer(0);
net: More BOOTP retry timeout improvements It's not unusual for DHCP servers to take a couple hundred milliseconds to respond to DHCP discover messages. One possible reason for the delay can be that the server checks (typically using an ARP request) that the IP it's about to hand out isn't in use yet. To make matters worse, some servers may also queue up requests and process them sequentially, which can cause excessively long delays if clients retry too fast. Commit f59be6e850b3 ("net: BOOTP retry timeout improvements") shortened the retry timeouts significantly, but the BOOTP/DHCP implementation in U-Boot doesn't handle that well because it will ignore incoming replies to earlier requests. In one particular setup this increases the time it takes to obtain a DHCP lease from 630 ms to 8313 ms. This commit attempts to fix this in two ways. First it increases the initial retry timeout from 10 ms to 250 ms to give DHCP servers some more time to respond. At the same time a cache of outstanding DHCP request IDs is kept so that the implementation will know to continue transactions even after a retransmission of the DISCOVER message. The maximum retry timeout is also increased from 1 second to 2 seconds. An ID cache of size 4 will keep DHCP requests around for 8 seconds (once the maximum retry timeout has been reached) before dropping them. This should give servers plenty of time to respond. If it ever turns out that this isn't enough, the size of the cache can easily be increased. With this commit the DHCP lease on the above-mentioned setup still takes longer (1230 ms) than originally, but that's an acceptable compromise to improve DHCP lease acquisition time for a broader range of setups. To make it easier to benchmark DHCP in the future, this commit also adds the time it took to obtain a lease to the final "DHCP client bound to address x.x.x.x" message. Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-19 08:21:24 +00:00
bootp_timeout = 250;
net: BOOTP retry timeout improvements Currently, the BOOTP code sends out its initial request as soon as the Ethernet driver indicates "link up". If this packet is lost or not replied to for some reason, the code waits for a 1s timeout before retrying. For some reason, such early packets are often lost on my system, so this causes an annoying delay. To optimize this, modify the BOOTP code to have very short timeouts for the first packet transmitted, but gradually increase the timeout each time a timeout occurs. This way, if the first packet is lost, the second packet is transmitted quite quickly and hence the overall delay is low. However, if there's still no response, we don't keep spewing out packets at an insane speed. It's arguably more correct to try and find out why the first packet is lost. However, it seems to disappear inside my Ethenet chip; the TX chip indicates no error during TX (not that it has much in the way of reporting...), yet wireshark on the RX side doesn't see any packet. FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is reported too early or based on the wrong condition in HW, and we should add some fixed extra delay into the driver. However, this would slow down every link up event even if it ends up not being needed in some cases. Having BOOTP retry quickly applies the fix/WAR to every possible Ethernet device, and is quite simple to implement, so seems a better solution. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-07-25 23:30:48 +00:00
}
void bootp_request(void)
2002-09-27 23:19:37 +00:00
{
uchar *pkt, *iphdr;
struct bootp_hdr *bp;
int extlen, pktlen, iplen;
int eth_hdr_size;
#ifdef CONFIG_BOOTP_RANDOM_DELAY
ulong rand_ms;
#endif
u32 bootp_id;
struct in_addr zero_ip;
struct in_addr bcast_ip;
2002-09-27 23:19:37 +00:00
bootstage_mark_name(BOOTSTAGE_ID_BOOTP_START, "bootp_start");
#if defined(CONFIG_CMD_DHCP)
2002-09-27 23:19:37 +00:00
dhcp_state = INIT;
#endif
#ifdef CONFIG_BOOTP_RANDOM_DELAY /* Random BOOTP delay */
if (bootp_try == 0)
srand_mac();
2002-09-27 23:19:37 +00:00
if (bootp_try <= 2) /* Start with max 1024 * 1ms */
rand_ms = rand() >> (22 - bootp_try);
else /* After 3rd BOOTP request max 8192 * 1ms */
rand_ms = rand() >> 19;
2002-09-27 23:19:37 +00:00
printf("Random delay: %ld ms...\n", rand_ms);
mdelay(rand_ms);
2002-09-27 23:19:37 +00:00
#endif /* CONFIG_BOOTP_RANDOM_DELAY */
printf("BOOTP broadcast %d\n", ++bootp_try);
pkt = net_tx_packet;
memset((void *)pkt, 0, PKTSIZE);
2002-09-27 23:19:37 +00:00
eth_hdr_size = net_set_ether(pkt, net_bcast_ethaddr, PROT_IP);
pkt += eth_hdr_size;
2002-09-27 23:19:37 +00:00
/*
* Next line results in incorrect packet size being transmitted,
* resulting in errors in some DHCP servers, reporting missing bytes.
* Size must be set in packet header after extension length has been
* determined.
2002-09-27 23:19:37 +00:00
* C. Hallinan, DS4.COM, Inc.
*/
/* net_set_udp_header(pkt, 0xFFFFFFFFL, PORT_BOOTPS, PORT_BOOTPC,
sizeof (struct bootp_hdr)); */
iphdr = pkt; /* We need this later for net_set_udp_header() */
pkt += IP_UDP_HDR_SIZE;
2002-09-27 23:19:37 +00:00
bp = (struct bootp_hdr *)pkt;
2002-09-27 23:19:37 +00:00
bp->bp_op = OP_BOOTREQUEST;
bp->bp_htype = HWT_ETHER;
bp->bp_hlen = HWL_ETHER;
bp->bp_hops = 0;
bp->bp_secs = htons(get_timer(0) / 1000);
zero_ip.s_addr = 0;
net_write_ip(&bp->bp_ciaddr, zero_ip);
net_write_ip(&bp->bp_yiaddr, zero_ip);
net_write_ip(&bp->bp_siaddr, zero_ip);
net_write_ip(&bp->bp_giaddr, zero_ip);
memcpy(bp->bp_chaddr, net_ethaddr, 6);
copy_filename(bp->bp_file, net_boot_file_name, sizeof(bp->bp_file));
2002-09-27 23:19:37 +00:00
/* Request additional information from the BOOTP/DHCP server */
#if defined(CONFIG_CMD_DHCP)
extlen = dhcp_extended((u8 *)bp->bp_vend, DHCP_DISCOVER, zero_ip,
zero_ip);
2002-09-27 23:19:37 +00:00
#else
extlen = bootp_extended((u8 *)bp->bp_vend);
#endif
2002-09-27 23:19:37 +00:00
/*
* Bootp ID is the lower 4 bytes of our ethernet address
* plus the current time in ms.
2002-09-27 23:19:37 +00:00
*/
bootp_id = ((u32)net_ethaddr[2] << 24)
| ((u32)net_ethaddr[3] << 16)
| ((u32)net_ethaddr[4] << 8)
| (u32)net_ethaddr[5];
bootp_id += get_timer(0);
bootp_id = htonl(bootp_id);
bootp_add_id(bootp_id);
net_copy_u32(&bp->bp_id, &bootp_id);
2002-09-27 23:19:37 +00:00
/*
* Calculate proper packet lengths taking into account the
* variable size of the options field
*/
iplen = BOOTP_HDR_SIZE - OPT_FIELD_SIZE + extlen;
pktlen = eth_hdr_size + IP_UDP_HDR_SIZE + iplen;
bcast_ip.s_addr = 0xFFFFFFFFL;
net_set_udp_header(iphdr, bcast_ip, PORT_BOOTPS, PORT_BOOTPC, iplen);
net_set_timeout_handler(bootp_timeout, bootp_timeout_handler);
2002-09-27 23:19:37 +00:00
#if defined(CONFIG_CMD_DHCP)
2002-09-27 23:19:37 +00:00
dhcp_state = SELECTING;
net_set_udp_handler(dhcp_handler);
2002-09-27 23:19:37 +00:00
#else
net_set_udp_handler(bootp_handler);
#endif
net_send_packet(net_tx_packet, pktlen);
2002-09-27 23:19:37 +00:00
}
#if defined(CONFIG_CMD_DHCP)
static void dhcp_process_options(uchar *popt, struct bootp_hdr *bp)
2002-09-27 23:19:37 +00:00
{
uchar *end = popt + BOOTP_HDR_SIZE;
2002-09-27 23:19:37 +00:00
int oplen, size;
#if defined(CONFIG_CMD_SNTP) && defined(CONFIG_BOOTP_TIMEOFFSET)
int *to_ptr;
#endif
2002-09-27 23:19:37 +00:00
while (popt < end && *popt != 0xff) {
2002-09-27 23:19:37 +00:00
oplen = *(popt + 1);
switch (*popt) {
case 1:
net_copy_ip(&net_netmask, (popt + 2));
break;
#if defined(CONFIG_CMD_SNTP) && defined(CONFIG_BOOTP_TIMEOFFSET)
case 2: /* Time offset */
to_ptr = &net_ntp_time_offset;
net_copy_u32((u32 *)to_ptr, (u32 *)(popt + 2));
net_ntp_time_offset = ntohl(net_ntp_time_offset);
break;
#endif
case 3:
net_copy_ip(&net_gateway, (popt + 2));
break;
case 6:
net_copy_ip(&net_dns_server, (popt + 2));
#if defined(CONFIG_BOOTP_DNS2)
if (*(popt + 1) > 4)
net_copy_ip(&net_dns_server2, (popt + 2 + 4));
#endif
break;
case 12:
size = truncate_sz("Host Name",
sizeof(net_hostname), oplen);
memcpy(&net_hostname, popt + 2, size);
net_hostname[size] = 0;
break;
case 15: /* Ignore Domain Name Option */
break;
case 17:
size = truncate_sz("Root Path",
sizeof(net_root_path), oplen);
memcpy(&net_root_path, popt + 2, size);
net_root_path[size] = 0;
break;
case 28: /* Ignore Broadcast Address Option */
break;
#if defined(CONFIG_CMD_SNTP) && defined(CONFIG_BOOTP_NTPSERVER)
case 42: /* NTP server IP */
net_copy_ip(&net_ntp_server, (popt + 2));
break;
#endif
case 51:
net_copy_u32(&dhcp_leasetime, (u32 *)(popt + 2));
break;
case 53: /* Ignore Message Type Option */
break;
case 54:
net_copy_ip(&dhcp_server_ip, (popt + 2));
break;
case 58: /* Ignore Renewal Time Option */
break;
case 59: /* Ignore Rebinding Time Option */
break;
case 66: /* Ignore TFTP server name */
break;
case 67: /* vendor opt bootfile */
/*
* I can't use dhcp_vendorex_proc here because I need
* to write into the bootp packet - even then I had to
* pass the bootp packet pointer into here as the
* second arg
*/
size = truncate_sz("Opt Boot File",
sizeof(bp->bp_file),
oplen);
if (bp->bp_file[0] == '\0' && size > 0) {
/*
* only use vendor boot file if we didn't
* receive a boot file in the main non-vendor
* part of the packet - god only knows why
* some vendors chose not to use this perfectly
* good spot to store the boot file (join on
* Tru64 Unix) it seems mind bogglingly crazy
* to me
*/
printf("*** WARNING: using vendor "
"optional boot file\n");
memcpy(bp->bp_file, popt + 2, size);
bp->bp_file[size] = '\0';
}
break;
default:
#if defined(CONFIG_BOOTP_VENDOREX)
if (dhcp_vendorex_proc(popt))
break;
2002-09-27 23:19:37 +00:00
#endif
printf("*** Unhandled DHCP Option in OFFER/ACK:"
" %d\n", *popt);
break;
2002-09-27 23:19:37 +00:00
}
popt += oplen + 2; /* Process next option */
}
}
static int dhcp_message_type(unsigned char *popt)
2002-09-27 23:19:37 +00:00
{
if (net_read_u32((u32 *)popt) != htonl(BOOTP_VENDOR_MAGIC))
2002-09-27 23:19:37 +00:00
return -1;
popt += 4;
while (*popt != 0xff) {
if (*popt == 53) /* DHCP Message Type */
2002-09-27 23:19:37 +00:00
return *(popt + 2);
popt += *(popt + 1) + 2; /* Scan through all options */
}
return -1;
}
static void dhcp_send_request_packet(struct bootp_hdr *bp_offer)
2002-09-27 23:19:37 +00:00
{
uchar *pkt, *iphdr;
struct bootp_hdr *bp;
2002-09-27 23:19:37 +00:00
int pktlen, iplen, extlen;
int eth_hdr_size;
struct in_addr offered_ip;
struct in_addr zero_ip;
struct in_addr bcast_ip;
2002-09-27 23:19:37 +00:00
debug("dhcp_send_request_packet: Sending DHCPREQUEST\n");
pkt = net_tx_packet;
memset((void *)pkt, 0, PKTSIZE);
2002-09-27 23:19:37 +00:00
eth_hdr_size = net_set_ether(pkt, net_bcast_ethaddr, PROT_IP);
pkt += eth_hdr_size;
2002-09-27 23:19:37 +00:00
iphdr = pkt; /* We'll need this later to set proper pkt size */
pkt += IP_UDP_HDR_SIZE;
2002-09-27 23:19:37 +00:00
bp = (struct bootp_hdr *)pkt;
2002-09-27 23:19:37 +00:00
bp->bp_op = OP_BOOTREQUEST;
bp->bp_htype = HWT_ETHER;
bp->bp_hlen = HWL_ETHER;
bp->bp_hops = 0;
bp->bp_secs = htons(get_timer(0) / 1000);
/* Do not set the client IP, your IP, or server IP yet, since it
* hasn't been ACK'ed by the server yet */
2006-10-11 22:01:08 +00:00
/*
* RFC3046 requires Relay Agents to discard packets with
* nonzero and offered giaddr
*/
zero_ip.s_addr = 0;
net_write_ip(&bp->bp_giaddr, zero_ip);
memcpy(bp->bp_chaddr, net_ethaddr, 6);
2002-09-27 23:19:37 +00:00
/*
* ID is the id of the OFFER packet
*/
net_copy_u32(&bp->bp_id, &bp_offer->bp_id);
2002-09-27 23:19:37 +00:00
/*
* Copy options from OFFER packet if present
*/
/* Copy offered IP into the parameters request list */
net_copy_ip(&offered_ip, &bp_offer->bp_yiaddr);
extlen = dhcp_extended((u8 *)bp->bp_vend, DHCP_REQUEST,
dhcp_server_ip, offered_ip);
2002-09-27 23:19:37 +00:00
iplen = BOOTP_HDR_SIZE - OPT_FIELD_SIZE + extlen;
pktlen = eth_hdr_size + IP_UDP_HDR_SIZE + iplen;
bcast_ip.s_addr = 0xFFFFFFFFL;
net_set_udp_header(iphdr, bcast_ip, PORT_BOOTPS, PORT_BOOTPC, iplen);
2002-09-27 23:19:37 +00:00
#ifdef CONFIG_BOOTP_DHCP_REQUEST_DELAY
udelay(CONFIG_BOOTP_DHCP_REQUEST_DELAY);
#endif /* CONFIG_BOOTP_DHCP_REQUEST_DELAY */
debug("Transmitting DHCPREQUEST packet: len = %d\n", pktlen);
net_send_packet(net_tx_packet, pktlen);
2002-09-27 23:19:37 +00:00
}
/*
* Handle DHCP received packets.
*/
static void dhcp_handler(uchar *pkt, unsigned dest, struct in_addr sip,
unsigned src, unsigned len)
2002-09-27 23:19:37 +00:00
{
struct bootp_hdr *bp = (struct bootp_hdr *)pkt;
2002-09-27 23:19:37 +00:00
debug("DHCPHandler: got packet: (src=%d, dst=%d, len=%d) state: %d\n",
src, dest, len, dhcp_state);
2002-09-27 23:19:37 +00:00
/* Filter out pkts we don't want */
if (check_packet(pkt, dest, src, len))
2002-09-27 23:19:37 +00:00
return;
debug("DHCPHandler: got DHCP packet: (src=%d, dst=%d, len=%d) state: "
"%d\n", src, dest, len, dhcp_state);
2002-09-27 23:19:37 +00:00
switch (dhcp_state) {
case SELECTING:
/*
* Wait an appropriate time for any potential DHCPOFFER packets
* to arrive. Then select one, and generate DHCPREQUEST
* response. If filename is in format we recognize, assume it
* is a valid OFFER from a server we want.
2002-09-27 23:19:37 +00:00
*/
debug("DHCP: state=SELECTING bp_file: \"%s\"\n", bp->bp_file);
#ifdef CONFIG_SYS_BOOTFILE_PREFIX
2002-09-27 23:19:37 +00:00
if (strncmp(bp->bp_file,
CONFIG_SYS_BOOTFILE_PREFIX,
strlen(CONFIG_SYS_BOOTFILE_PREFIX)) == 0) {
#endif /* CONFIG_SYS_BOOTFILE_PREFIX */
2002-09-27 23:19:37 +00:00
debug("TRANSITIONING TO REQUESTING STATE\n");
2002-09-27 23:19:37 +00:00
dhcp_state = REQUESTING;
if (net_read_u32((u32 *)&bp->bp_vend[0]) ==
htonl(BOOTP_VENDOR_MAGIC))
dhcp_process_options((u8 *)&bp->bp_vend[4], bp);
2002-09-27 23:19:37 +00:00
net_set_timeout_handler(5000, bootp_timeout_handler);
dhcp_send_request_packet(bp);
#ifdef CONFIG_SYS_BOOTFILE_PREFIX
2002-09-27 23:19:37 +00:00
}
#endif /* CONFIG_SYS_BOOTFILE_PREFIX */
2002-09-27 23:19:37 +00:00
return;
break;
case REQUESTING:
debug("DHCP State: REQUESTING\n");
2002-09-27 23:19:37 +00:00
if (dhcp_message_type((u8 *)bp->bp_vend) == DHCP_ACK) {
if (net_read_u32((u32 *)&bp->bp_vend[0]) ==
htonl(BOOTP_VENDOR_MAGIC))
dhcp_process_options((u8 *)&bp->bp_vend[4], bp);
/* Store net params from reply */
store_net_params(bp);
2002-09-27 23:19:37 +00:00
dhcp_state = BOUND;
net: More BOOTP retry timeout improvements It's not unusual for DHCP servers to take a couple hundred milliseconds to respond to DHCP discover messages. One possible reason for the delay can be that the server checks (typically using an ARP request) that the IP it's about to hand out isn't in use yet. To make matters worse, some servers may also queue up requests and process them sequentially, which can cause excessively long delays if clients retry too fast. Commit f59be6e850b3 ("net: BOOTP retry timeout improvements") shortened the retry timeouts significantly, but the BOOTP/DHCP implementation in U-Boot doesn't handle that well because it will ignore incoming replies to earlier requests. In one particular setup this increases the time it takes to obtain a DHCP lease from 630 ms to 8313 ms. This commit attempts to fix this in two ways. First it increases the initial retry timeout from 10 ms to 250 ms to give DHCP servers some more time to respond. At the same time a cache of outstanding DHCP request IDs is kept so that the implementation will know to continue transactions even after a retransmission of the DISCOVER message. The maximum retry timeout is also increased from 1 second to 2 seconds. An ID cache of size 4 will keep DHCP requests around for 8 seconds (once the maximum retry timeout has been reached) before dropping them. This should give servers plenty of time to respond. If it ever turns out that this isn't enough, the size of the cache can easily be increased. With this commit the DHCP lease on the above-mentioned setup still takes longer (1230 ms) than originally, but that's an acceptable compromise to improve DHCP lease acquisition time for a broader range of setups. To make it easier to benchmark DHCP in the future, this commit also adds the time it took to obtain a lease to the final "DHCP client bound to address x.x.x.x" message. Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-08-19 08:21:24 +00:00
printf("DHCP client bound to address %pI4 (%lu ms)\n",
&net_ip, get_timer(bootp_start));
bootstage_mark_name(BOOTSTAGE_ID_BOOTP_STOP,
"bootp_stop");
2002-09-27 23:19:37 +00:00
net_auto_load();
2002-09-27 23:19:37 +00:00
return;
}
break;
case BOUND:
/* DHCP client bound to address */
break;
2002-09-27 23:19:37 +00:00
default:
puts("DHCP: INVALID STATE\n");
2002-09-27 23:19:37 +00:00
break;
}
}
void dhcp_request(void)
2002-09-27 23:19:37 +00:00
{
bootp_request();
2002-09-27 23:19:37 +00:00
}
#endif /* CONFIG_CMD_DHCP */