u-boot/include/configs/ap_sh4a_4a.h

116 lines
3.6 KiB
C
Raw Normal View History

/*
* Configuation settings for the Alpha Project AP-SH4A-4A board
*
* Copyright (C) 2012 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __AP_SH4A_4A_H
#define __AP_SH4A_4A_H
#define CONFIG_CPU_SH7734 1
#define CONFIG_AP_SH4A_4A 1
#define CONFIG_400MHZ_MODE 1
/* #define CONFIG_533MHZ_MODE 1 */
#define CONFIG_SYS_TEXT_BASE 0x8BFC0000
#define CONFIG_DISPLAY_BOARDINFO
#undef CONFIG_SHOW_BOOT_PROGRESS
/* Ether */
#define CONFIG_SH_ETHER 1
#define CONFIG_SH_ETHER_USE_PORT (0)
#define CONFIG_SH_ETHER_PHY_ADDR (0x0)
#define CONFIG_SH_ETHER_PHY_MODE (PHY_INTERFACE_MODE_GMII)
#define CONFIG_SH_ETHER_SH7734_MII (0x02) /* GMII */
#define CONFIG_BITBANGMII
#define CONFIG_BITBANGMII_MULTI
/* undef to save memory */
#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */
/* Buffer size for Console output */
#define CONFIG_SYS_PBSIZE 256
/* List of legal baudrate settings for this board */
#define CONFIG_SYS_BAUDRATE_TABLE { 115200 }
/* SCIF */
#define CONFIG_SCIF 1
#define CONFIG_CONS_SCIF4 1
/* Suppress display of console information at boot */
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE (0x88000000)
#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024)
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024)
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE)
/* Enable alternate, more extensive, memory test */
#undef CONFIG_SYS_ALT_MEMTEST
/* Scratch address used by the alternate memory test */
#undef CONFIG_SYS_MEMTEST_SCRATCH
/* Enable temporary baudrate change while serial download */
#undef CONFIG_SYS_LOADS_BAUD_CHANGE
/* FLASH */
#define CONFIG_FLASH_CFI_DRIVER 1
#define CONFIG_SYS_FLASH_CFI
#undef CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BASE (0xA0000000)
#define CONFIG_SYS_MAX_FLASH_SECT 512
/* if you use all NOR Flash , you change dip-switch. Please see Manual. */
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
/* Timeout for Flash erase operations (in ms) */
#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000)
/* Timeout for Flash write operations (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000)
/* Timeout for Flash set sector lock bit operations (in ms) */
#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000)
/* Timeout for Flash clear lock bit operations (in ms) */
#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000)
/*
* Use hardware flash sectors protection instead
* of U-Boot software protection
*/
#undef CONFIG_SYS_FLASH_PROTECTION
#undef CONFIG_SYS_DIRECT_FLASH_TFTP
/* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE)
/* Monitor size */
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
/* Size of DRAM reserved for malloc() use */
#define CONFIG_SYS_MALLOC_LEN (256 * 1024)
#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024)
/* ENV setting */
#define CONFIG_ENV_OVERWRITE 1
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
/* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */
#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE)
/* Board Clock */
#if defined(CONFIG_400MHZ_MODE)
#define CONFIG_SYS_CLK_FREQ 50000000
#else
#define CONFIG_SYS_CLK_FREQ 44444444
#endif
#define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ
#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_TMU_CLK_DIV 4
#endif /* __AP_SH4A_4A_H */