u-boot/board/congatec/common/Makefile

#
# (C) Copyright 2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# SPDX-License-Identifier:	GPL-2.0+
#

MINIMAL=

ifdef CONFIG_SPL_BUILD
ifndef CONFIG_TPL_BUILD
ifdef CONFIG_SPL_INIT_MINIMAL
MINIMAL=y
endif
endif
endif

ifdef MINIMAL
# necessary to create built-in.o
obj- := __dummy__.o
else

obj-y				+= mmc.o

endif
imx: support for conga-QMX8 board Add i.MX8QM qmx8 congatec board support U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200) CPU: NXP i.MX8QM RevB A53 at 1200 MHz Model: Congatec QMX8 Qseven series Board: conga-QMX8 Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9 Boot: SD2 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 switch to partitions #0, OK mmc2 is current device Net: Error: ethernet@5b040000 address not set. No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> 2021-05-31 13:50:40 +00:00			`#`
			`# (C) Copyright 2006`
			`# Wolfgang Denk, DENX Software Engineering, wd@denx.de.`
			`#`
			`# SPDX-License-Identifier: GPL-2.0+`
			`#`

			`MINIMAL=`

			`ifdef CONFIG_SPL_BUILD`
Convert CONFIG_SPL_INIT_MINIMAL et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_INIT_MINIMAL CONFIG_SPL_FLUSH_IMAGE CONFIG_SPL_SKIP_RELOCATE Signed-off-by: Tom Rini <trini@konsulko.com> 2022-05-13 16:26:35 +00:00			`ifndef CONFIG_TPL_BUILD`
imx: support for conga-QMX8 board Add i.MX8QM qmx8 congatec board support U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200) CPU: NXP i.MX8QM RevB A53 at 1200 MHz Model: Congatec QMX8 Qseven series Board: conga-QMX8 Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9 Boot: SD2 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 switch to partitions #0, OK mmc2 is current device Net: Error: ethernet@5b040000 address not set. No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> 2021-05-31 13:50:40 +00:00			`ifdef CONFIG_SPL_INIT_MINIMAL`
			`MINIMAL=y`
			`endif`
			`endif`
Convert CONFIG_SPL_INIT_MINIMAL et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_INIT_MINIMAL CONFIG_SPL_FLUSH_IMAGE CONFIG_SPL_SKIP_RELOCATE Signed-off-by: Tom Rini <trini@konsulko.com> 2022-05-13 16:26:35 +00:00			`endif`
imx: support for conga-QMX8 board Add i.MX8QM qmx8 congatec board support U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200) CPU: NXP i.MX8QM RevB A53 at 1200 MHz Model: Congatec QMX8 Qseven series Board: conga-QMX8 Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9 Boot: SD2 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 switch to partitions #0, OK mmc2 is current device Net: Error: ethernet@5b040000 address not set. No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> 2021-05-31 13:50:40 +00:00
			`ifdef MINIMAL`
			`# necessary to create built-in.o`
			`obj- := __dummy__.o`
			`else`

			`obj-y += mmc.o`

			`endif`