u-boot/configs/Mele_M9_defconfig

CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI,SUNXI_GMAC"
CONFIG_FDTFILE="sun6i-a31-m9.dtb"
+S:CONFIG_ARM=y
+S:CONFIG_ARCH_SUNXI=y
+S:CONFIG_MACH_SUN6I=y
+S:CONFIG_TARGET_MELE_M9=y
+S:CONFIG_DRAM_CLK=312
+S:CONFIG_DRAM_ZQ=120
# The Mele M9 uses 3.3V for general IO
+S:CONFIG_AXP221_DCDC1_VOLT=3300
# Ethernet phy power
+S:CONFIG_AXP221_DLDO1_VOLT=3300
# USB hub power
+S:CONFIG_AXP221_DLDO4_VOLT=3300
# Wifi power
+S:CONFIG_AXP221_ALDO1_VOLT=3300
# Vbus gpio for usb1
+S:CONFIG_USB1_VBUS_PIN="PC27"
# No Vbus gpio for usb2
+S:CONFIG_USB2_VBUS_PIN=""
sun6i: Add Mele M9 board Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2014-10-27 22:29:49 +00:00			`CONFIG_SPL=y`
sun6i: Add gmac support for sun6i boards Hookup the gmac found on the sun6i / A31 SoCs. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2014-11-21 16:19:45 +00:00			`CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI,SUNXI_GMAC"`
sun6i: Add Mele M9 board Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2014-10-27 22:29:49 +00:00			`CONFIG_FDTFILE="sun6i-a31-m9.dtb"`
			`+S:CONFIG_ARM=y`
			`+S:CONFIG_ARCH_SUNXI=y`
			`+S:CONFIG_MACH_SUN6I=y`
			`+S:CONFIG_TARGET_MELE_M9=y`
sun6i: Make dram clk and zq value Kconfig options It turns out that there is a too large spread between boards to handle this with a default value, turn this into Kconfig options, and set the values the factory images are using for the Colombus and Mele_M9 boards. Note this changes the ZQ default when not overriden through defconfig from 120 to 123, as that is what most boards seem to actually use. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2014-11-15 18:46:39 +00:00			`+S:CONFIG_DRAM_CLK=312`
			`+S:CONFIG_DRAM_ZQ=120`
sunxi: axp221: Make dcdc1 voltage configurable The dcdc1 voltage is typically used as generic 3.3V IO voltage for things like GPIO-s, sdcard interfaces, etc. On most boards this is undervolted to 3.0V to safe battery, but not on all, make it configurable so that we can use the same settings as the original firmware on all boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2014-12-13 13:12:06 +00:00			`# The Mele M9 uses 3.3V for general IO`
			`+S:CONFIG_AXP221_DCDC1_VOLT=3300`
sun6i: Add Mele M9 board Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2014-10-27 22:29:49 +00:00			`# Ethernet phy power`
			`+S:CONFIG_AXP221_DLDO1_VOLT=3300`
			`# USB hub power`
			`+S:CONFIG_AXP221_DLDO4_VOLT=3300`
			`# Wifi power`
			`+S:CONFIG_AXP221_ALDO1_VOLT=3300`
sun6i: Correct Mele M9 Vbus gpio settings I noticed that the kernel and u-boot settings were different, double checking has confirmed that the kernel settings are correct. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2014-11-23 11:33:20 +00:00			`# Vbus gpio for usb1`
			`+S:CONFIG_USB1_VBUS_PIN="PC27"`
			`# No Vbus gpio for usb2`
			`+S:CONFIG_USB2_VBUS_PIN=""`