mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 15:37:23 +00:00
102 lines
2.7 KiB
Text
102 lines
2.7 KiB
Text
|
Overview
|
||
|
|
--------
|
||
|
|
The P1023 process includes a performance optimized implementation of the
|
||
|
|
QorIQ data Path Acceleration Architecture (DPAA). This architecture
|
||
|
|
provides the infrastructure to support simplified sharing of networking
|
||
|
|
interfaces and accelerators by multiple CPU cores. P1023 is an e500 based
|
||
|
|
dual core SOC.
|
||
|
|
|
||
|
|
P1023RDS board is a Low End Dual core platform supporting the P1023
|
||
|
|
processor of QorIQ series.
|
||
|
|
|
||
|
|
Building U-boot
|
||
|
|
---------------
|
||
|
|
To build the u-boot for P1023RDS:
|
||
|
|
Configure to NOR boot:
|
||
|
|
make P1023RDS_config
|
||
|
|
Configure to NAND boot:
|
||
|
|
make P1023RDS_NAND_config
|
||
|
|
Build:
|
||
|
|
make
|
||
|
|
|
||
|
|
Board Switches
|
||
|
|
--------------
|
||
|
|
Most switches on the board should not be changed. The most frequent
|
||
|
|
user-settable switches on the board are used to configure
|
||
|
|
the flash banks.
|
||
|
|
|
||
|
|
J4: all open
|
||
|
|
|
||
|
|
Default NOR flash boot switch setting:
|
||
|
|
Sw3[1:8]: off on on off on on off off
|
||
|
|
Sw4[1:8]: off off off on off off off off
|
||
|
|
Sw6[1:8]: off on off on off on on off
|
||
|
|
Sw7[1:8]: off on off off on off off off
|
||
|
|
Sw8[1:8]: on off off off off off off off
|
||
|
|
|
||
|
|
For NAND flash boot,set
|
||
|
|
Sw4[1:4]: off on on on
|
||
|
|
|
||
|
|
The default native ethernet setting is for RGMII mode.
|
||
|
|
To use SGMII mode, set
|
||
|
|
SW8[1:2]: OFF OFF
|
||
|
|
SW7[6:7]: ON ON
|
||
|
|
|
||
|
|
Memory Map
|
||
|
|
----------
|
||
|
|
0x0000_0000 0x7fff_ffff DDR 2G Cacheable
|
||
|
|
0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
|
||
|
|
0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
|
||
|
|
0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
|
||
|
|
|
||
|
|
0xe000_0000 0xe003_ffff BCSR 256K BCSR
|
||
|
|
0xee00_0000 0xefff_ffff NOR flash 32M NOR flash
|
||
|
|
0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M
|
||
|
|
0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
|
||
|
|
0xffa0_0000 0xffaf_ffff NAND FLASH 1M non-cacheable
|
||
|
|
0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
|
||
|
|
|
||
|
|
Flashing u-boot Images
|
||
|
|
---------------
|
||
|
|
To program the image in the boot flash bank:
|
||
|
|
NOR flash boot:
|
||
|
|
=> tftp 1000000 u-boot.bin
|
||
|
|
=> protect off all
|
||
|
|
=> erase eff80000 efffffff
|
||
|
|
=> cp.b 1000000 eff80000 80000
|
||
|
|
|
||
|
|
NAND flash boot:
|
||
|
|
=> tftp 1000000 u-boot-nand.bin
|
||
|
|
=> nand erase 0 80000
|
||
|
|
=> nand write 1000000 0 80000
|
||
|
|
|
||
|
|
Firmware ucode location
|
||
|
|
---------------------------------
|
||
|
|
Microcode(ucode) to FMAN's IRAM is needed to make FMAN Ethernet work.
|
||
|
|
u-boot loads ucode FLASH. The location for ucode:
|
||
|
|
NOR Flash: 0xfe000000
|
||
|
|
NAND Flash: 0x1f00000
|
||
|
|
|
||
|
|
Using the Device Tree Source File
|
||
|
|
---------------------------------
|
||
|
|
To create the DTB (Device Tree Binary) image file,
|
||
|
|
use a command similar to this:
|
||
|
|
|
||
|
|
dtc -b 0 -f -I dts -O dtb p1023rds.dts > p1023rds.dtb
|
||
|
|
|
||
|
|
Likely, that .dts file will come from here;
|
||
|
|
|
||
|
|
linux-2.6/arch/powerpc/boot/dts/p1023rds.dts
|
||
|
|
or
|
||
|
|
make p1023rds.dtb ARCH=powerpc
|
||
|
|
in linux-2.6 directory.
|
||
|
|
|
||
|
|
Booting Linux
|
||
|
|
-------------
|
||
|
|
Place a linux uImage in the TFTP disk area.
|
||
|
|
|
||
|
|
tftp 1000000 uImage
|
||
|
|
tftp 2000000 rootfs.ext2.gz.uboot
|
||
|
|
tftp c00000 p1023rds.dtb
|
||
|
|
bootm 1000000 2000000 c00000
|