mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-22 19:23:07 +00:00
92 lines
2 KiB
C
92 lines
2 KiB
C
|
// SPDX-License-Identifier: GPL-2.0+
|
||
|
|
/*
|
||
|
|
* Copyright 2014 Freescale Semiconductor, Inc.
|
||
|
|
* Copyright 2020 Hitachi Power Grids. All rights reserved.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <common.h>
|
||
|
|
#include <fsl_ddr_sdram.h>
|
||
|
|
#include <fsl_ddr_dimm_params.h>
|
||
|
|
#include <asm/io.h>
|
||
|
|
#include <asm/arch/clock.h>
|
||
|
|
#include <asm/global_data.h>
|
||
|
|
#include <asm/arch/ls102xa_soc.h>
|
||
|
|
|
||
|
|
DECLARE_GLOBAL_DATA_PTR;
|
||
|
|
|
||
|
|
void fsl_ddr_board_options(memctl_options_t *popts,
|
||
|
|
dimm_params_t *pdimm,
|
||
|
|
unsigned int ctrl_num)
|
||
|
|
{
|
||
|
|
if (ctrl_num > 1) {
|
||
|
|
printf("Not supported controller number %d\n", ctrl_num);
|
||
|
|
return;
|
||
|
|
}
|
||
|
|
|
||
|
|
// 1/2 DRAM cycle (should be increased in case of ADDR/CMD heavily loaded than the clock)
|
||
|
|
popts->clk_adjust = 0x4;
|
||
|
|
popts->write_data_delay = 0x4;
|
||
|
|
// wr leveling start value for lane 0
|
||
|
|
popts->wrlvl_start = 0x5;
|
||
|
|
// wr leveling start values for lanes 1-3 (lane 4 not there)
|
||
|
|
popts->wrlvl_ctl_2 = 0x05050500;
|
||
|
|
// 32-bit DRAM, no need to set start values for lanes we do not have (5-8)
|
||
|
|
popts->wrlvl_ctl_3 = 0x0;
|
||
|
|
popts->cpo_override = 0x1f;
|
||
|
|
|
||
|
|
/* force DDR bus width to 32 bits */
|
||
|
|
popts->data_bus_width = 1;
|
||
|
|
popts->otf_burst_chop_en = 0;
|
||
|
|
popts->burst_length = DDR_BL8;
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Factors to consider for half-strength driver enable:
|
||
|
|
* - number of DIMMs installed
|
||
|
|
*/
|
||
|
|
popts->half_strength_driver_enable = 1;
|
||
|
|
/*
|
||
|
|
* Write leveling override
|
||
|
|
*/
|
||
|
|
popts->wrlvl_override = 1;
|
||
|
|
popts->wrlvl_sample = 0xf;
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Rtt and Rtt_WR override
|
||
|
|
*/
|
||
|
|
popts->rtt_override = 0;
|
||
|
|
|
||
|
|
/* Enable ZQ calibration */
|
||
|
|
popts->zq_en = 1;
|
||
|
|
|
||
|
|
popts->cswl_override = DDR_CSWL_CS0;
|
||
|
|
|
||
|
|
/* optimize cpo for erratum A-009942 */
|
||
|
|
popts->cpo_sample = 0x58;
|
||
|
|
|
||
|
|
/* DHC_EN =1, ODT = 75 Ohm */
|
||
|
|
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
|
||
|
|
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
|
||
|
|
}
|
||
|
|
|
||
|
|
int fsl_initdram(void)
|
||
|
|
{
|
||
|
|
phys_size_t dram_size;
|
||
|
|
|
||
|
|
puts("Initializing DDR....using SPD\n");
|
||
|
|
dram_size = fsl_ddr_sdram();
|
||
|
|
|
||
|
|
erratum_a008850_post();
|
||
|
|
|
||
|
|
gd->ram_size = dram_size;
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
int dram_init_banksize(void)
|
||
|
|
{
|
||
|
|
gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
|
||
|
|
gd->bd->bi_dram[0].size = gd->ram_size;
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|