u-boot/include/configs/zynq_microzed.h

/*
 * (C) Copyright 2013 Xilinx, Inc.
 *
 * Configuration for Micro Zynq Evaluation and Development Board - MicroZedBoard
 * See zynq-common.h for Zynq common configs
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_ZYNQ_MICROZED_H
#define __CONFIG_ZYNQ_MICROZED_H

#define CONFIG_SYS_SDRAM_SIZE		(1024 * 1024 * 1024)

#define CONFIG_ZYNQ_SERIAL_UART1
#define CONFIG_ZYNQ_GEM0
#define CONFIG_ZYNQ_GEM_PHY_ADDR0	0

#define CONFIG_SYS_NO_FLASH

#define CONFIG_ZYNQ_SDHCI0
#define CONFIG_DEFAULT_DEVICE_TREE	zynq-microzed

#include <configs/zynq-common.h>

#endif /* __CONFIG_ZYNQ_MICROZED_H */
zynq: Add zynq microzed board support MicroZed is a low-cost development board based on the Xilinx Zynq-7000 All Programmable SoC. APSOC: - XC7Z010-1CLG400C Memory: - 1 GB of DDR3 SDRAM - 128Mb of QSPI flash(S25FL128SAGBHI200) - Micro SD card interface Communication: - 10/100/1000 Ethernet - USB 2.0 - USB-UART User I/O: - 100 User I/O (50 per connector) - Configurable as up to 48 LVDS pairs or 100 single-ended I/O Misc: - Xilinx PC4 JTAG configuration port - PS JTAG pins accessible via Pmod - 33.33 MHz oscillator - User LED and push switch For more info - http://zedboard.org/product/microzed Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> 2014-01-08 20:18:17 +00:00			`/*`
			`* (C) Copyright 2013 Xilinx, Inc.`
			`*`
			`* Configuration for Micro Zynq Evaluation and Development Board - MicroZedBoard`
			`* See zynq-common.h for Zynq common configs`
			`*`
			`* SPDX-License-Identifier: GPL-2.0+`
			`*/`

			`#ifndef __CONFIG_ZYNQ_MICROZED_H`
			`#define __CONFIG_ZYNQ_MICROZED_H`

			`#define CONFIG_SYS_SDRAM_SIZE (1024 * 1024 * 1024)`

			`#define CONFIG_ZYNQ_SERIAL_UART1`
			`#define CONFIG_ZYNQ_GEM0`
			`#define CONFIG_ZYNQ_GEM_PHY_ADDR0 0`

			`#define CONFIG_SYS_NO_FLASH`

			`#define CONFIG_ZYNQ_SDHCI0`
zynq: Enable CONFIG_DEFAULT_DEVICE_TREE Enabled default dts files on respective pre-board config files this is way MAKEALL will works. and it's upto user to build specific dts by specifying at build time. $ make zynq_zc70x_config $ make --> with default dts zynq-zc702.dts or $ make DEVICE_TREE=zynq-zc702 --> Same configuration with zynq-zc706.dts Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> 2014-01-08 20:18:30 +00:00			`#define CONFIG_DEFAULT_DEVICE_TREE zynq-microzed`
zynq: Add zynq microzed board support MicroZed is a low-cost development board based on the Xilinx Zynq-7000 All Programmable SoC. APSOC: - XC7Z010-1CLG400C Memory: - 1 GB of DDR3 SDRAM - 128Mb of QSPI flash(S25FL128SAGBHI200) - Micro SD card interface Communication: - 10/100/1000 Ethernet - USB 2.0 - USB-UART User I/O: - 100 User I/O (50 per connector) - Configurable as up to 48 LVDS pairs or 100 single-ended I/O Misc: - Xilinx PC4 JTAG configuration port - PS JTAG pins accessible via Pmod - 33.33 MHz oscillator - User LED and push switch For more info - http://zedboard.org/product/microzed Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> 2014-01-08 20:18:17 +00:00
			`#include <configs/zynq-common.h>`

			`#endif /* __CONFIG_ZYNQ_MICROZED_H */`