u-boot/include/configs/hrcon.h

441 lines
13 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2014
* Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
*
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 family */
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
/*
* SERDES
*/
#define CONFIG_FSL_SERDES
#define CONFIG_FSL_SERDES1 0xe3000
/*
* DDR Setup
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
| DDRCDR_PZ_LOZ \
| DDRCDR_NZ_LOZ \
| DDRCDR_ODT \
| DDRCDR_Q_DRN)
/* 0x7b880001 */
/*
* Manually set up DDR parameters
* consist of one chip NT5TU64M16HG from NANYA
*/
#define CONFIG_SYS_DDR_SIZE 128 /* MB */
#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
| CSCONFIG_ODT_RD_NEVER \
| CSCONFIG_ODT_WR_ONLY_CURRENT \
| CSCONFIG_BANK_BIT_3 \
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
/* 0x80010102 */
#define CONFIG_SYS_DDR_TIMING_3 0
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
| (0 << TIMING_CFG0_WRT_SHIFT) \
| (0 << TIMING_CFG0_RRT_SHIFT) \
| (0 << TIMING_CFG0_WWT_SHIFT) \
| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
| (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
/* 0x00260802 */
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
| (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
| (7 << TIMING_CFG1_CASLAT_SHIFT) \
| (9 << TIMING_CFG1_REFREC_SHIFT) \
| (2 << TIMING_CFG1_WRREC_SHIFT) \
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
| (2 << TIMING_CFG1_WRTORD_SHIFT))
/* 0x26279222 */
#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
| (4 << TIMING_CFG2_CPO_SHIFT) \
| (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
/* 0x021848c5 */
#define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \
| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
/* 0x08240100 */
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
| SDRAM_CFG_DBW_16)
/* 0x43100000 */
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
#define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
| (0x0242 << SDRAM_MODE_SD_SHIFT))
/* ODT 150ohm CL=4, AL=0 on SDRAM */
#define CONFIG_SYS_DDR_MODE2 0x00000000
/*
* Memory test
*/
#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x07f00000
/*
* The reserved memory
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
*/
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* FLASH on the Local Bus
*/
#if 1
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_FLASH_CFI_LEGACY
#define CONFIG_SYS_FLASH_LEGACY_512Kx16
#endif
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 135
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_FPGA_DONE(k) 0x0010
#define CONFIG_SYS_FPGA_COUNT 1
#define CONFIG_SYS_MCLINK_MAX 3
#define CONFIG_SYS_FPGA_PTR \
{ (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }
/*
* Serial Port
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
/* Pass open firmware flat tree */
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_PCA953X /* NXP PCA9554 */
#define CONFIG_PCA9698 /* NXP PCA9698 */
#define CONFIG_SYS_I2C_IHS
#define CONFIG_SYS_I2C_IHS_CH0
#define CONFIG_SYS_I2C_IHS_SPEED_0 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F
#define CONFIG_SYS_I2C_IHS_CH1
#define CONFIG_SYS_I2C_IHS_SPEED_1 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F
#define CONFIG_SYS_I2C_IHS_CH2
#define CONFIG_SYS_I2C_IHS_SPEED_2 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F
#define CONFIG_SYS_I2C_IHS_CH3
#define CONFIG_SYS_I2C_IHS_SPEED_3 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F
#ifdef CONFIG_HRCON_DH
#define CONFIG_SYS_I2C_IHS_DUAL
#define CONFIG_SYS_I2C_IHS_CH0_1
#define CONFIG_SYS_I2C_IHS_SPEED_0_1 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_0_1 0x7F
#define CONFIG_SYS_I2C_IHS_CH1_1
#define CONFIG_SYS_I2C_IHS_SPEED_1_1 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_1_1 0x7F
#define CONFIG_SYS_I2C_IHS_CH2_1
#define CONFIG_SYS_I2C_IHS_SPEED_2_1 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_2_1 0x7F
#define CONFIG_SYS_I2C_IHS_CH3_1
#define CONFIG_SYS_I2C_IHS_SPEED_3_1 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_3_1 0x7F
#endif
/*
* Software (bit-bang) I2C driver configuration
*/
#define CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
#define I2C_SOFT_DECLARATIONS2
#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F
#define I2C_SOFT_DECLARATIONS3
#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F
#define I2C_SOFT_DECLARATIONS4
#define CONFIG_SYS_I2C_SOFT_SPEED_4 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F
#define I2C_SOFT_DECLARATIONS5
#define CONFIG_SYS_I2C_SOFT_SPEED_5 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_5 0x7F
#define I2C_SOFT_DECLARATIONS6
#define CONFIG_SYS_I2C_SOFT_SPEED_6 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_6 0x7F
#define I2C_SOFT_DECLARATIONS7
#define CONFIG_SYS_I2C_SOFT_SPEED_7 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_7 0x7F
#define I2C_SOFT_DECLARATIONS8
#define CONFIG_SYS_I2C_SOFT_SPEED_8 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_8 0x7F
#ifdef CONFIG_HRCON_DH
#define I2C_SOFT_DECLARATIONS9
#define CONFIG_SYS_I2C_SOFT_SPEED_9 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_9 0x7F
#define I2C_SOFT_DECLARATIONS10
#define CONFIG_SYS_I2C_SOFT_SPEED_10 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_10 0x7F
#define I2C_SOFT_DECLARATIONS11
#define CONFIG_SYS_I2C_SOFT_SPEED_11 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_11 0x7F
#define I2C_SOFT_DECLARATIONS12
#define CONFIG_SYS_I2C_SOFT_SPEED_12 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_12 0x7F
#endif
#ifdef CONFIG_HRCON_DH
#define CONFIG_SYS_ICS8N3QV01_I2C {13, 14, 15, 16, 17, 18, 19, 20}
#define CONFIG_SYS_DP501_I2C {1, 3, 5, 7, 2, 4, 6, 8}
#define CONFIG_HRCON_FANS { {10, 0x4c}, {11, 0x4c}, \
{12, 0x4c} }
#else
#define CONFIG_SYS_ICS8N3QV01_I2C {9, 10, 11, 12}
#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4}
#define CONFIG_HRCON_FANS { {6, 0x4c}, {7, 0x4c}, \
{8, 0x4c} }
#endif
#ifndef __ASSEMBLY__
void fpga_gpio_set(unsigned int bus, int pin);
void fpga_gpio_clear(unsigned int bus, int pin);
int fpga_gpio_get(unsigned int bus, int pin);
void fpga_control_set(unsigned int bus, int pin);
void fpga_control_clear(unsigned int bus, int pin);
#endif
#define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200)
#define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100)
#define I2C_FPGA_IDX (I2C_ADAP_HWNR % 4)
#ifdef CONFIG_HRCON_DH
#define I2C_ACTIVE \
do { \
if (I2C_ADAP_HWNR > 7) \
fpga_control_set(I2C_FPGA_IDX, 0x0004); \
else \
fpga_control_clear(I2C_FPGA_IDX, 0x0004); \
} while (0)
#else
#define I2C_ACTIVE { }
#endif
#define I2C_TRISTATE { }
#define I2C_READ \
(fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0)
#define I2C_SDA(bit) \
do { \
if (bit) \
fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \
else \
fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \
} while (0)
#define I2C_SCL(bit) \
do { \
if (bit) \
fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \
else \
fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \
} while (0)
#define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */
/*
* Software (bit-bang) MII driver configuration
*/
#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
#define CONFIG_BITBANGMII_MULTI
/*
* OSD Setup
*/
#define CONFIG_SYS_OSD_SCREENS 1
#define CONFIG_SYS_DP501_DIFFERENTIAL
#define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */
#ifdef CONFIG_HRCON_DH
#define CONFIG_SYS_OSD_DH
#endif
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
/* enable PCIE clock */
#define CONFIG_SYS_SCCR_PCIEXP1CM 1
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCIE
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
/*
* TSEC
*/
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
/*
* TSEC ethernet configuration
*/
#define CONFIG_TSEC1
#define CONFIG_TSEC1_NAME "eTSEC0"
#define TSEC1_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC1_FLAGS TSEC_GIGABIT
/* Options are: eTSEC[0-1] */
#define CONFIG_ETHPRIME "eTSEC0"
/*
* Environment
*/
#if 1
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#else
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* Command line configuration.
*/
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
/*
* Environment Configuration
*/
#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#endif
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_HOSTNAME "hrcon"
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \
"u-boot=u-boot.bin\0" \
"kernel_addr=1000000\0" \
"fdt_addr=C00000\0" \
"fdtfile=hrcon.dtb\0" \
"load=tftp ${loadaddr} ${u-boot}\0" \
"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
" +${filesize};cp.b ${fileaddr} " \
__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
"upd=run load update\0" \
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp ${kernel_addr} $bootfile;" \
"tftp ${fdt_addr} $fdtfile;" \
"bootm ${kernel_addr} - ${fdt_addr}"
#define CONFIG_MMCBOOTCOMMAND \
"setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \
"console=$consoledev,$baudrate $othbootargs;" \
"ext2load mmc 0:2 ${kernel_addr} $bootfile;" \
"ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \
"bootm ${kernel_addr} - ${fdt_addr}"
#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
#endif /* __CONFIG_H */