u-boot/board/freescale/bsc9131rdb/README

Overview
--------
- BSC9131 is integrated device that targets Femto base station market.
 It combines Power Architecture e500v2 and DSP StarCore SC3850 core
 technologies with MAPLE-B2F baseband acceleration processing elements.
- It's MAPLE disabled personality is called 9231.

The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte shared
  L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
  Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
 Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
 and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
 Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
 operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
 ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network acceleration
  including IEEE 1588. v2 hardware support and virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
  JESD207/three custom ADI RF interfaces (two dual port and one single port)
  and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD support
. Universal Subscriber Identity Module (USIM) interface that facilitates
  communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers

The e500 core subsystem within the Power Architecture consists of the following:
. 32-Kbyte L1 instruction cache
. 32-Kbyte L1 data cache
. 256-Kbyte L2 cache/L2 memory/L2 stash
. programmable interrupt controller (PIC)
. Debug support
. Timers

The SC3850 core subsystem consists of the following:
. 32 Kbyte 8-way level 1 instruction cache (L1 ICache)
. 32 Kbyte 8-way level 1 data cache (L1 DCache)
. 512 Kbyte 8-way level 2 unified instruction/data cache (M2 memory)
. Memory management unit (MMU)
. Enhanced programmable interrupt controller (EPIC)
. Debug and profiling unit (DPU)
. Two 32-bit timers

BSC9131RDB board Overview
-------------------------
 1Gbyte DDR3 (on board DDR)
 128Mbyte 2K page size NAND Flash
 256 Kbit M24256 I2C EEPROM
 128 Mbit SPI Flash memory
 USB-ULPI
 eTSEC1: Connected to RGMII PHY
 eTSEC2: Connected to RGMII PHY
 DUART interface: supports one UARTs up to 115200 bps for console display
 USIM connector

Frequency Combinations Supported
--------------------------------
Core MHz/CCB MHz/DDR(MT/s)
1. 1000/500/800
2. 800/400/667

Boot Methods Supported
-----------------------
1. NAND Flash
2. SPI Flash

Default Boot Method
--------------------
NAND boot

Building U-boot
--------------
To build the u-boot for BSC9131RDB:
1. NAND Flash with sysclk 66MHz(J16 on RDB closed, default)
	make BSC9131RDB_NAND
2. NAND Flash with sysclk 100MHz(J16 on RDB open)
	make BSC9131RDB_NAND_SYSCLK100
3. SPI Flash with sysclk 66MHz(J16 on RDB closed, default)
	make BSC9131RDB_SPIFLASH
4. SPI Flash with sysclk 100MHz(J16 on RDB open)
	make BSC9131RDB_SPIFLASH_SYSCLK100

Memory map
-----------
 0x0000_0000	0x7FFF_FFFF	DDR			1G cacheable
 0xA0000000	0xBFFFFFFF	Shared DSP core L2/M2 space	512M
 0xC100_0000	0xC13F_FFFF	MAPLE-2F		4M
 0xC1F0_0000	0xC1F3_FFFF	PA SRAM Region 0	256K
 0xC1F8_0000	0xC1F9_FFFF	PA SRAM Region 1	128K
 0xFED0_0000	0xFED0_3FFF	SEC Secured RAM		16K
 0xFEE0_0000	0xFEE0_0FFF	DSP Boot ROM		4K
 0xFF60_0000	0xFF6F_FFFF 	DSP CCSR		1M
 0xFF70_0000	0xFF7F_FFFF	PA CCSR			1M
 0xFF80_0000	0xFFFF_FFFF	Boot Page & NAND Buffer 8M

DDR Memory map
---------------
 0x0000_0000	0x36FF_FFFF	Memory passed onto Linux
 0x3700_0000	0x37FF_FFFF	PowerPC-DSP shared control area
 0x3800_0000	0x4FFF_FFFF	DSP Private area

 Out of 880M, passed onto Linux, 1hugetlb page of 256M is reserved for
 data communcation between PowerPC and DSP core.
 Rest is PowerPC private area.

Flashing Images
---------------
To place a new u-boot image in the NAND flash and then boot
with that new image temporarily, use this:
	tftp 1000000 u-boot-nand.bin
	nand erase 0 100000
	nand write 1000000 0 100000
	reset

Using the Device Tree Source File
---------------------------------
To create the DTB (Device Tree Binary) image file,
use a command similar to this:

	dtc -b 0 -f -I dts -O dtb bsc9131rdb.dts > bsc9131rdb.dtb

Likely, that .dts file will come from here;

	linux-2.6/arch/powerpc/boot/dts/bsc9131rdb.dts

Booting Linux
-------------
Place a linux uImage in the TFTP disk area.

	tftp 1000000 uImage
	tftp 2000000 rootfs.ext2.gz.uboot
	tftp c00000 bsc9131rdb.dtb
	bootm 1000000 2000000 c00000