Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-10 23:24:38 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/configs/uniphier_v7_defconfig

63 lines
1.6 KiB
Text
Raw Normal View History

ARM: uniphier: add ProXstream2 and PH1-LD6b support The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-21 15:27:41 +00:00
CONFIG_ARM=y
CONFIG_ARCH_UNIPHIER=y
configs: Re-sync Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-13 17:48:42 +00:00
CONFIG_SYS_TEXT_BASE=0x84000000
Revert "Increase default of CONFIG_SYS_MALLOC_F_LEN for SPL_OF_CONTROL" This reverts commit 90c08d9e08c7a108ab904f3bbdeb558081757892. I took a closer look at this after the commit was applied, and found CONFIG_SYS_MALLOC_F_LEN=0x2000 was too much. 8KB memory for SPL is actually too big for some boards. Perhaps 0x800 is enough, but the situation varies board by board. Let's postpone our decision until we come up with a better idea. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-19 12:40:26 +00:00
CONFIG_SYS_MALLOC_F_LEN=0x2000
ARM: uniphier: move CONFIG_SPL_* to defconfig or select As I repeated in the ML, I am unhappy with config entries with bare defaults. Kick them out of arch/arm/mach-uniphier/Kconfig. Currently, CONFIG_SPL_SERIAL_SUPPORT is not user-configurable (build fails without it), but it should be fixed later anyway, so I am moving CONFIG_SPL_SERIAL_SUPPORT to defconfigs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-20 05:27:00 +00:00
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
env: Finish migration of common ENV options - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-19 01:02:10 +00:00
CONFIG_ENV_SIZE=0x2000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 19:54:04 +00:00
CONFIG_NR_DRAM_BANKS=3
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08 00:27:54 +00:00
CONFIG_SPL=y
ARM: uniphier: add ProXstream2 and PH1-LD6b support The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-21 15:27:41 +00:00
CONFIG_MICRO_SUPPORT_CARD=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-23 15:47:37 +00:00
CONFIG_SPL_TEXT_BASE=0x00100000
ARM: uniphier: disable CONFIG_ARCH_FIXUP_FDT_MEMORY Do not overwrite the memory nodes in the kernel DT where some parts of the memory region might be carved out. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-05 09:31:38 +00:00
# CONFIG_ARCH_FIXUP_FDT_MEMORY is not set
ARM: uniphier: allow to source boot script before distro-boot Some users might need additional setups before booting the kernel. If there is found a file 'boot.scr', run it before invoking the distro boot command. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-19 11:03:14 +00:00
CONFIG_BOOTCOMMAND="run ${bootdev}script; run ${bootdev}boot"
preboot: Introduce CONFIG_USE_PREBOOT and migrate CONFIG_PREBOOT This is the same migration path as commit b6251db8c3f0 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND"). I also moved the description in README to the Kconfig help. I ripped off the sentence about 'LWMON' since it is gone already. I only let my boards migrate, leaving the rest to platform maintainers. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-02-14 02:05:33 +00:00
CONFIG_USE_PREBOOT=y
CONFIG_PREBOOT="env exist ${bootdev}preboot && run ${bootdev}preboot"
ARM: uniphier: set CONFIG_LOGLEVEL to 6 Print out KERN_NOTICE or higher level log messages. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-24 15:25:31 +00:00
CONFIG_LOGLEVEL=6
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 15:57:37 +00:00
CONFIG_SPL_NAND_SUPPORT=y
Convert CONFIG_SPL_NOR_SUPPORT to Kconfig Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-13 05:18:51 +00:00
CONFIG_SPL_NOR_SUPPORT=y
ARM: uniphier: enable CONFIG_CMD_CONFIG This command is useful to see which config options are enabled on the running U-Boot image. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-21 06:09:11 +00:00
CONFIG_CMD_CONFIG=y
cmd: Toggle the default value of CONFIG_CMD_IMLS Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-08 18:48:01 +00:00
CONFIG_CMD_IMLS=y
ARM: uniphier: add ProXstream2 and PH1-LD6b support The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-21 15:27:41 +00:00
# CONFIG_CMD_XIMG is not set
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 23:58:53 +00:00
CONFIG_CMD_GPIO=y
ARM: uniphier: enable CONFIG_CMD_GPT Enable CONFIG_CMD_GPT, keeping CONFIG_SPL_EFI_PARTITION because the SPL for UniPhier platform does not recognize any partitions. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-17 07:17:55 +00:00
CONFIG_CMD_GPT=y
ARM: uniphier: add ProXstream2 and PH1-LD6b support The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-21 15:27:41 +00:00
CONFIG_CMD_I2C=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 23:58:53 +00:00
CONFIG_CMD_MMC=y
ARM: uniphier: add ProXstream2 and PH1-LD6b support The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-21 15:27:41 +00:00
CONFIG_CMD_USB=y
CONFIG_CMD_TFTPPUT=y
ARM: uniphier: enable CONFIG_CMD_CACHE This will be useful, for example, to load firmware to DRAM and make it visible to other agents. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-08-28 03:44:41 +00:00
CONFIG_CMD_CACHE=y
ARM: uniphier: add ProXstream2 and PH1-LD6b support The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-21 15:27:41 +00:00
CONFIG_CMD_TIME=y
# CONFIG_CMD_MISC is not set
configs: Migrate and re-enabled CONFIG_CMD_MTDPARTS Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms that had been enabling it turn it on by hand. This exposed that we had not yet migrated CMD_MTDPARTS fully, so do so now. Fixes: 86dfa556d927 ("cmd: ubi: Remove useless call to mtdparts_init()") Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-14 00:54:45 +00:00
CONFIG_CMD_MTDPARTS=y
ARM: uniphier: enable MTD partition and UBI Enable "mtdparts" and "ubi" commands for uniphier_v8_defconfig to use UBI on NAND devices. Enable only "mtdparts" for uniphier_{v7,ld4_sld8}_defconfig because enabling UBI would increase 170KB, which would be memory footprint problem. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-07-19 07:28:27 +00:00
CONFIG_MTDIDS_DEFAULT="nand0=uniphier-nand.0"
CONFIG_MTDPARTS_DEFAULT="mtdparts=uniphier-nand.0:1m(firmware),-(UBI)"
ARM: uniphier: enable CONFIG_CMD_UBI Now that CONFIG_SYS_MONITOR_LEN increased, we have room for enabling more options again. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-10 03:58:34 +00:00
CONFIG_CMD_UBI=y
ARM: uniphier: disable CONFIG_SPL_DOS_PARTITION The SPL for UniPhier platform does not recognize any partitions. Do not compile unneeded features. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-17 07:17:39 +00:00
# CONFIG_SPL_DOS_PARTITION is not set
ARM: uniphier: enable CONFIG_CMD_GPT Enable CONFIG_CMD_GPT, keeping CONFIG_SPL_EFI_PARTITION because the SPL for UniPhier platform does not recognize any partitions. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-17 07:17:55 +00:00
# CONFIG_SPL_EFI_PARTITION is not set
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 19:26:12 +00:00
CONFIG_DEFAULT_DEVICE_TREE="uniphier-pxs2-vodka"
env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-13 03:46:36 +00:00
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
ARM: uniphier: add ProXstream2 and PH1-LD6b support The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-21 15:27:41 +00:00
CONFIG_NET_RANDOM_ETHADDR=y
ARM: uniphier: enable GPIO command and driver for UniPhier SoCs This allows to use the "gpio" command. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-02-16 08:03:50 +00:00
CONFIG_GPIO_UNIPHIER=y
ARM: uniphier: move CONFIG_I2C_EEPROM to defconfig We already have the entry for this option in Kconfig, so let's migrate to it. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-26 18:47:58 +00:00
CONFIG_MISC=y
CONFIG_I2C_EEPROM=y
Kconfig: Add EEPROM options to Kconfig when I2C_EEPROM is set Add the following options to drivers/misc/Kconfig: SYS_I2C_EEPROM_ADDR SYS_I2C_EEPROM_BUS SYS_EEPROM_SIZE SYS_EEPROM_PAGE_WRITE_BITS SYS_EEPROM_PAGE_WRITE_DELAY_MS SYS_I2C_EEPROM_ADDR_LEN SYS_I2C_EEPROM_ADDR_OVERFLOW This does not migrate any boards, but provides a foundations for those who want/need these options Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Migrate uniphier] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-13 14:00:28 +00:00
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=10
Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-05-01 07:58:27 +00:00
CONFIG_SUPPORT_EMMC_BOOT=y
ARM: uniphier: enable UniPhier SD/MMC host driver Enable the driver in all UniPhier defconfig files and add some needed defines to the common files. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-18 10:52:49 +00:00
CONFIG_MMC_UNIPHIER=y
Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-14 20:10:50 +00:00
CONFIG_FLASH_CFI_DRIVER=y
CONFIG_SYS_FLASH_CFI=y
ARM: uniphier: move CONFIG_NAND to defconfig This imply was added when the option was moved by the moveconfig tool, but the intention is not clear. Move it to defconfig. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-29 06:41:32 +00:00
CONFIG_NAND=y
ARM: uniphier: enable CONFIG_NAND_DENALI_DT Migrate to the DT-based NAND init entry. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-26 08:58:02 +00:00
CONFIG_NAND_DENALI_DT=y
ARM: uniphier: add ProXstream2 and PH1-LD6b support The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-21 15:27:41 +00:00
CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES=8
CONFIG_SPL_NAND_DENALI=y
ARM: uniphier: enable CONFIG_SNI_AVE and disable CONFIG_SMC911X Enable the on-chip ethernet driver for uniphier_{v7,v8}_defconfig. Disable the on-board SMC911x because it has not migrated to the driver model yet - it is not possible to enable DM and non-DM drivers at the same time. The CONFIG_SMC911X for uniphier_ld4_sld8_defconfig is still kept because the on-chip ethernet driver for LD4, sLD8 is not supported yet. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-06-19 07:11:42 +00:00
CONFIG_DM_ETH=y
CONFIG_SNI_AVE=y
ARM: uniphier: add ProXstream2 and PH1-LD6b support The DDR SDRAM initialization code has not been mainlined yet, but U-Boot proper should work. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-21 15:27:41 +00:00
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
ARM: uniphier: enable DWC3 xHCI driver really I thought commit d37d31849c6a ("ARM: uniphier: enable DWC3 xHCI driver") enabled CONFIG_USB_DWC3_UNIPHIER, but CONFIG_USB_XHCI_DWC3 was missing in uniphier_v7_defconfig. Re-add. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-17 12:19:40 +00:00
CONFIG_USB_XHCI_DWC3=y
ARM: uniphier: merge two defconfig files into uniphier_v7_defconfig The main difference between Pro4 and PXs2/LD6b is the Denali NAND IP version. This is now distinguished by DT. Merge the two defconfig files into uniphier_v7_defconfig. Update the README.uniphier too. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-15 12:43:20 +00:00
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_GENERIC=y
ARM: uniphier: enable DWC3 xHCI driver Enable CONFIGs for the DWC3 core and the UniPhier specific glue layer. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-13 17:21:16 +00:00
CONFIG_USB_DWC3=y
ARM: uniphier: enable DWC3 xHCI driver really I thought commit d37d31849c6a ("ARM: uniphier: enable DWC3 xHCI driver") enabled CONFIG_USB_DWC3_UNIPHIER, but CONFIG_USB_XHCI_DWC3 was missing in uniphier_v7_defconfig. Re-add. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-17 12:19:40 +00:00
CONFIG_USB_DWC3_UNIPHIER=y
Move CONFIG_PANIC_HANG to Kconfig Freescale (NXP) boards have lots of defconfig files per board. I used "imply PANIC_HANG" for them. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-04 03:37:00 +00:00
CONFIG_PANIC_HANG=y
ARM: uniphier: enable MTD partition and UBI Enable "mtdparts" and "ubi" commands for uniphier_v8_defconfig to use UBI on NAND devices. Enable only "mtdparts" for uniphier_{v7,ld4_sld8}_defconfig because enabling UBI would increase 170KB, which would be memory footprint problem. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-07-19 07:28:27 +00:00
CONFIG_FDT_FIXUP_PARTITIONS=y
Reference in a new issue Copy permalink