u-boot/arch/arm/mach-meson/board-gx.c

272 lines
6.6 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2016 Beniamino Galvani <b.galvani@gmail.com>
* (C) Copyright 2018 Neil Armstrong <narmstrong@baylibre.com>
*/
#include <common.h>
#include <init.h>
#include <net.h>
#include <asm/arch/boot.h>
#include <asm/arch/eth.h>
#include <asm/arch/gx.h>
#include <asm/arch/mem.h>
#include <asm/arch/meson-vpu.h>
#include <asm/io.h>
#include <asm/armv8/mmu.h>
ARM: arch-meson: build memory banks using reported memory from registers As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware and a secondary BL32 firmware. Since mid-2017, the reserved memory address of the BL31 firmware was moved and grown for security reasons. But mainline U-Boot and Linux has the old address and size fixed. These SoCs have a register interface to get the two firmware reserved memory start and sizes. This patch adds a dynamic reservation of the memory zones in the device tree bootmem reserved memory zone used by the kernel in early boot. To be complete, the memory zones are also added to the EFI reserved zones. Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2]. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html Changes since v1: - switched the #if to if(IS_ENABLED()) to compile all code paths - renamed function to meson_board_add_reserved_memory() - added a mem.h header with comment - updated all boards ft_board_setup() Changes since RFC v2: - reduced preprocessor load - kept Odroid-C2 static memory mapping as exception Changes since RFC v1: - switch to fdt rsv mem table and efi reserve memory - replaced in_le32 by readl() Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> [trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 09:35:46 +00:00
#include <linux/sizes.h>
#include <usb.h>
#include <linux/usb/otg.h>
#include <asm/arch/usb-gx.h>
#include <usb/dwc2_udc.h>
#include <clk.h>
#include <phy.h>
DECLARE_GLOBAL_DATA_PTR;
int meson_get_boot_device(void)
{
return readl(GX_AO_SEC_GP_CFG0) & GX_AO_BOOT_DEVICE;
}
/* Configure the reserved memory zones exported by the secure registers
* into EFI and DTB reserved memory entries.
*/
void meson_init_reserved_memory(void *fdt)
ARM: arch-meson: build memory banks using reported memory from registers As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware and a secondary BL32 firmware. Since mid-2017, the reserved memory address of the BL31 firmware was moved and grown for security reasons. But mainline U-Boot and Linux has the old address and size fixed. These SoCs have a register interface to get the two firmware reserved memory start and sizes. This patch adds a dynamic reservation of the memory zones in the device tree bootmem reserved memory zone used by the kernel in early boot. To be complete, the memory zones are also added to the EFI reserved zones. Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2]. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html Changes since v1: - switched the #if to if(IS_ENABLED()) to compile all code paths - renamed function to meson_board_add_reserved_memory() - added a mem.h header with comment - updated all boards ft_board_setup() Changes since RFC v2: - reduced preprocessor load - kept Odroid-C2 static memory mapping as exception Changes since RFC v1: - switch to fdt rsv mem table and efi reserve memory - replaced in_le32 by readl() Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> [trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 09:35:46 +00:00
{
u64 bl31_size, bl31_start;
u64 bl32_size, bl32_start;
u32 reg;
/*
* Get ARM Trusted Firmware reserved memory zones in :
* - AO_SEC_GP_CFG3: bl32 & bl31 size in KiB, can be 0
* - AO_SEC_GP_CFG5: bl31 physical start address, can be NULL
* - AO_SEC_GP_CFG4: bl32 physical start address, can be NULL
*/
reg = readl(GX_AO_SEC_GP_CFG3);
ARM: arch-meson: build memory banks using reported memory from registers As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware and a secondary BL32 firmware. Since mid-2017, the reserved memory address of the BL31 firmware was moved and grown for security reasons. But mainline U-Boot and Linux has the old address and size fixed. These SoCs have a register interface to get the two firmware reserved memory start and sizes. This patch adds a dynamic reservation of the memory zones in the device tree bootmem reserved memory zone used by the kernel in early boot. To be complete, the memory zones are also added to the EFI reserved zones. Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2]. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html Changes since v1: - switched the #if to if(IS_ENABLED()) to compile all code paths - renamed function to meson_board_add_reserved_memory() - added a mem.h header with comment - updated all boards ft_board_setup() Changes since RFC v2: - reduced preprocessor load - kept Odroid-C2 static memory mapping as exception Changes since RFC v1: - switch to fdt rsv mem table and efi reserve memory - replaced in_le32 by readl() Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> [trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 09:35:46 +00:00
bl31_size = ((reg & GX_AO_BL31_RSVMEM_SIZE_MASK)
>> GX_AO_BL31_RSVMEM_SIZE_SHIFT) * SZ_1K;
bl32_size = (reg & GX_AO_BL32_RSVMEM_SIZE_MASK) * SZ_1K;
ARM: arch-meson: build memory banks using reported memory from registers As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware and a secondary BL32 firmware. Since mid-2017, the reserved memory address of the BL31 firmware was moved and grown for security reasons. But mainline U-Boot and Linux has the old address and size fixed. These SoCs have a register interface to get the two firmware reserved memory start and sizes. This patch adds a dynamic reservation of the memory zones in the device tree bootmem reserved memory zone used by the kernel in early boot. To be complete, the memory zones are also added to the EFI reserved zones. Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2]. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html Changes since v1: - switched the #if to if(IS_ENABLED()) to compile all code paths - renamed function to meson_board_add_reserved_memory() - added a mem.h header with comment - updated all boards ft_board_setup() Changes since RFC v2: - reduced preprocessor load - kept Odroid-C2 static memory mapping as exception Changes since RFC v1: - switch to fdt rsv mem table and efi reserve memory - replaced in_le32 by readl() Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> [trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 09:35:46 +00:00
bl31_start = readl(GX_AO_SEC_GP_CFG5);
bl32_start = readl(GX_AO_SEC_GP_CFG4);
ARM: arch-meson: build memory banks using reported memory from registers As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware and a secondary BL32 firmware. Since mid-2017, the reserved memory address of the BL31 firmware was moved and grown for security reasons. But mainline U-Boot and Linux has the old address and size fixed. These SoCs have a register interface to get the two firmware reserved memory start and sizes. This patch adds a dynamic reservation of the memory zones in the device tree bootmem reserved memory zone used by the kernel in early boot. To be complete, the memory zones are also added to the EFI reserved zones. Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2]. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html Changes since v1: - switched the #if to if(IS_ENABLED()) to compile all code paths - renamed function to meson_board_add_reserved_memory() - added a mem.h header with comment - updated all boards ft_board_setup() Changes since RFC v2: - reduced preprocessor load - kept Odroid-C2 static memory mapping as exception Changes since RFC v1: - switch to fdt rsv mem table and efi reserve memory - replaced in_le32 by readl() Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> [trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 09:35:46 +00:00
/*
* Early Meson GX Firmware revisions did not provide the reserved
ARM: arch-meson: build memory banks using reported memory from registers As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware and a secondary BL32 firmware. Since mid-2017, the reserved memory address of the BL31 firmware was moved and grown for security reasons. But mainline U-Boot and Linux has the old address and size fixed. These SoCs have a register interface to get the two firmware reserved memory start and sizes. This patch adds a dynamic reservation of the memory zones in the device tree bootmem reserved memory zone used by the kernel in early boot. To be complete, the memory zones are also added to the EFI reserved zones. Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2]. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html Changes since v1: - switched the #if to if(IS_ENABLED()) to compile all code paths - renamed function to meson_board_add_reserved_memory() - added a mem.h header with comment - updated all boards ft_board_setup() Changes since RFC v2: - reduced preprocessor load - kept Odroid-C2 static memory mapping as exception Changes since RFC v1: - switch to fdt rsv mem table and efi reserve memory - replaced in_le32 by readl() Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> [trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 09:35:46 +00:00
* memory zones in the registers, keep fixed memory zone handling.
*/
if (IS_ENABLED(CONFIG_MESON_GX) &&
ARM: arch-meson: build memory banks using reported memory from registers As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware and a secondary BL32 firmware. Since mid-2017, the reserved memory address of the BL31 firmware was moved and grown for security reasons. But mainline U-Boot and Linux has the old address and size fixed. These SoCs have a register interface to get the two firmware reserved memory start and sizes. This patch adds a dynamic reservation of the memory zones in the device tree bootmem reserved memory zone used by the kernel in early boot. To be complete, the memory zones are also added to the EFI reserved zones. Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2]. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html Changes since v1: - switched the #if to if(IS_ENABLED()) to compile all code paths - renamed function to meson_board_add_reserved_memory() - added a mem.h header with comment - updated all boards ft_board_setup() Changes since RFC v2: - reduced preprocessor load - kept Odroid-C2 static memory mapping as exception Changes since RFC v1: - switch to fdt rsv mem table and efi reserve memory - replaced in_le32 by readl() Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> [trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 09:35:46 +00:00
!reg && !bl31_start && !bl32_start) {
bl31_start = 0x10000000;
bl31_size = 0x200000;
}
/* Add first 16MiB reserved zone */
meson_board_add_reserved_memory(fdt, 0, GX_FIRMWARE_MEM_SIZE);
ARM: arch-meson: build memory banks using reported memory from registers As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware and a secondary BL32 firmware. Since mid-2017, the reserved memory address of the BL31 firmware was moved and grown for security reasons. But mainline U-Boot and Linux has the old address and size fixed. These SoCs have a register interface to get the two firmware reserved memory start and sizes. This patch adds a dynamic reservation of the memory zones in the device tree bootmem reserved memory zone used by the kernel in early boot. To be complete, the memory zones are also added to the EFI reserved zones. Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2]. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html Changes since v1: - switched the #if to if(IS_ENABLED()) to compile all code paths - renamed function to meson_board_add_reserved_memory() - added a mem.h header with comment - updated all boards ft_board_setup() Changes since RFC v2: - reduced preprocessor load - kept Odroid-C2 static memory mapping as exception Changes since RFC v1: - switch to fdt rsv mem table and efi reserve memory - replaced in_le32 by readl() Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> [trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 09:35:46 +00:00
/* Add BL31 reserved zone */
if (bl31_start && bl31_size)
meson_board_add_reserved_memory(fdt, bl31_start, bl31_size);
/* Add BL32 reserved zone */
if (bl32_start && bl32_size)
meson_board_add_reserved_memory(fdt, bl32_start, bl32_size);
#if defined(CONFIG_VIDEO_MESON)
meson_vpu_rsv_fb(fdt);
#endif
}
phys_size_t get_effective_memsize(void)
{
/* Size is reported in MiB, convert it in bytes */
return ((readl(GX_AO_SEC_GP_CFG0) & GX_AO_MEM_SIZE_MASK)
>> GX_AO_MEM_SIZE_SHIFT) * SZ_1M;
}
static struct mm_region gx_mem_map[] = {
{
.virt = 0x0UL,
.phys = 0x0UL,
.size = 0xc0000000UL,
.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
PTE_BLOCK_INNER_SHARE
}, {
.virt = 0xc0000000UL,
.phys = 0xc0000000UL,
.size = 0x30000000UL,
.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
PTE_BLOCK_NON_SHARE |
PTE_BLOCK_PXN | PTE_BLOCK_UXN
}, {
/* List terminator */
0,
}
};
struct mm_region *mem_map = gx_mem_map;
/* Configure the Ethernet MAC with the requested interface mode
* with some optional flags.
*/
void meson_eth_init(phy_interface_t mode, unsigned int flags)
{
switch (mode) {
case PHY_INTERFACE_MODE_RGMII:
case PHY_INTERFACE_MODE_RGMII_ID:
case PHY_INTERFACE_MODE_RGMII_RXID:
case PHY_INTERFACE_MODE_RGMII_TXID:
/* Set RGMII mode */
setbits_le32(GX_ETH_REG_0, GX_ETH_REG_0_PHY_INTF |
GX_ETH_REG_0_TX_PHASE(1) |
GX_ETH_REG_0_TX_RATIO(4) |
GX_ETH_REG_0_PHY_CLK_EN |
GX_ETH_REG_0_CLK_EN);
/* Reset to external PHY */
if(!IS_ENABLED(CONFIG_MESON_GXBB))
writel(0x2009087f, GX_ETH_REG_3);
break;
case PHY_INTERFACE_MODE_RMII:
/* Set RMII mode */
out_le32(GX_ETH_REG_0, GX_ETH_REG_0_INVERT_RMII_CLK |
GX_ETH_REG_0_CLK_EN);
/* Use GXL RMII Internal PHY (also on GXM) */
if (!IS_ENABLED(CONFIG_MESON_GXBB)) {
if ((flags & MESON_USE_INTERNAL_RMII_PHY)) {
writel(0x10110181, GX_ETH_REG_2);
writel(0xe40908ff, GX_ETH_REG_3);
} else
writel(0x2009087f, GX_ETH_REG_3);
}
break;
default:
printf("Invalid Ethernet interface mode\n");
return;
}
/* Enable power gate */
clrbits_le32(GX_MEM_PD_REG_0, GX_MEM_PD_REG_0_ETH_MASK);
}
#if CONFIG_IS_ENABLED(USB_XHCI_DWC3_OF_SIMPLE) && \
CONFIG_IS_ENABLED(USB_GADGET_DWC2_OTG)
static struct dwc2_plat_otg_data meson_gx_dwc2_data;
static struct phy usb_phys[2];
int board_usb_init(int index, enum usb_init_type init)
{
struct ofnode_phandle_args args;
struct udevice *clk_dev;
ofnode dwc2_node;
struct clk clk;
int ret, i;
u32 val;
/* find the dwc2 node */
dwc2_node = ofnode_by_compatible(ofnode_null(), "snps,dwc2");
if (!ofnode_valid(dwc2_node)) {
debug("Not found dwc2 node\n");
return -ENODEV;
}
if (!ofnode_is_available(dwc2_node)) {
debug("dwc2 is disabled in the device tree\n");
return -ENODEV;
}
/* get the PHYs */
for (i = 0; i < 2; i++) {
ret = generic_phy_get_by_index_nodev(dwc2_node, i,
&usb_phys[i]);
if (ret && ret != -ENOENT) {
pr_err("Failed to get USB PHY%d for %s\n",
i, ofnode_get_name(dwc2_node));
return ret;
}
}
for (i = 0; i < 2; i++) {
ret = generic_phy_init(&usb_phys[i]);
if (ret) {
pr_err("Can't init USB PHY%d for %s\n",
i, ofnode_get_name(dwc2_node));
return ret;
}
}
for (i = 0; i < 2; i++) {
ret = generic_phy_power_on(&usb_phys[i]);
if (ret) {
pr_err("Can't power USB PHY%d for %s\n",
i, ofnode_get_name(dwc2_node));
return ret;
}
}
phy_meson_gxl_usb3_set_mode(&usb_phys[0], USB_DR_MODE_PERIPHERAL);
phy_meson_gxl_usb2_set_mode(&usb_phys[1], USB_DR_MODE_PERIPHERAL);
meson_gx_dwc2_data.regs_otg = ofnode_get_addr(dwc2_node);
if (meson_gx_dwc2_data.regs_otg == FDT_ADDR_T_NONE) {
debug("usbotg: can't get base address\n");
return -ENODATA;
}
/* Enable clock */
ret = ofnode_parse_phandle_with_args(dwc2_node, "clocks",
"#clock-cells", 0, 0, &args);
if (ret) {
debug("usbotg has no clocks defined in the device tree\n");
return ret;
}
ret = uclass_get_device_by_ofnode(UCLASS_CLK, args.node, &clk_dev);
if (ret)
return ret;
if (args.args_count != 1) {
debug("Can't find clock ID in the device tree\n");
return -ENODATA;
}
clk.dev = clk_dev;
clk.id = args.args[0];
ret = clk_enable(&clk);
if (ret) {
debug("Failed to enable usbotg clock\n");
return ret;
}
ofnode_read_u32(dwc2_node, "g-rx-fifo-size", &val);
meson_gx_dwc2_data.rx_fifo_sz = val;
ofnode_read_u32(dwc2_node, "g-np-tx-fifo-size", &val);
meson_gx_dwc2_data.np_tx_fifo_sz = val;
ofnode_read_u32(dwc2_node, "g-tx-fifo-size", &val);
meson_gx_dwc2_data.tx_fifo_sz = val;
return dwc2_udc_probe(&meson_gx_dwc2_data);
}
int board_usb_cleanup(int index, enum usb_init_type init)
{
int i;
phy_meson_gxl_usb3_set_mode(&usb_phys[0], USB_DR_MODE_HOST);
phy_meson_gxl_usb2_set_mode(&usb_phys[1], USB_DR_MODE_HOST);
for (i = 0; i < 2; i++)
usb_phys[i].dev = NULL;
return 0;
}
#endif