u-boot/include/configs/salvator-x.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * include/configs/salvator-x.h
 *     This file is Salvator-X board configuration.
 *
 * Copyright (C) 2015 Renesas Electronics Corporation
 */

#ifndef __SALVATOR_X_H
#define __SALVATOR_X_H

#include "rcar-gen3-common.h"

/* Generic Timer Definitions (use in assembler source) */
#define COUNTER_FREQUENCY	0xFE502A	/* 16.66MHz from CPclk */

/* Environment in eMMC, at the end of 2nd "boot sector" */

#define CONFIG_FLASH_SHOW_PROGRESS	45
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_SYS_FLASH_BANKS_LIST	{ 0x08000000 }
#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
#define CONFIG_SYS_MAX_FLASH_SECT	256
#define CONFIG_SYS_WRITE_SWAPPED_DATA

#endif /* __SALVATOR_X_H */
SPDX: Convert all of our single license tags to Linux Kernel style When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com> 2018-05-06 21:58:06 +00:00			`/* SPDX-License-Identifier: GPL-2.0+ */`
ARM: rmobile: Add support salvator-x board Salvator-x is an entry level development board based on R-Car H3 SoC (R8A7795). This commit supports SCIF only. Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> 2016-03-31 18:51:36 +00:00			`/*`
			`* include/configs/salvator-x.h`
			`* This file is Salvator-X board configuration.`
			`*`
			`* Copyright (C) 2015 Renesas Electronics Corporation`
			`*/`

			`#ifndef __SALVATOR_X_H`
			`#define __SALVATOR_X_H`

			`#include "rcar-gen3-common.h"`

			`/* Generic Timer Definitions (use in assembler source) */`
			`#define COUNTER_FREQUENCY 0xFE502A /* 16.66MHz from CPclk */`

ARM: rmobile: salvator-x: Add SD support Add support for the SD card slots on the Salvator-X board. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> 2017-05-13 13:57:46 +00:00			`/* Environment in eMMC, at the end of 2nd "boot sector" */`

ARM: rmobile: Enable RPC on Salvator-X, ULCB, Ebisu Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965 Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF accessible, mainline ATF is mandatory and must be built with RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for development and testing convenience only and must be disabled in deployment for platform security reasons. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> 2017-07-29 19:28:50 +00:00			`#define CONFIG_FLASH_SHOW_PROGRESS 45`
			`#define CONFIG_SYS_FLASH_QUIET_TEST`
			`#define CONFIG_SYS_FLASH_BANKS_LIST { 0x08000000 }`
			`#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT`
			`#define CONFIG_SYS_MAX_FLASH_SECT 256`
			`#define CONFIG_SYS_WRITE_SWAPPED_DATA`

ARM: rmobile: Add support salvator-x board Salvator-x is an entry level development board based on R-Car H3 SoC (R8A7795). This commit supports SCIF only. Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> 2016-03-31 18:51:36 +00:00			`#endif /* __SALVATOR_X_H */`