u-boot/arch/arm/dts/s5p4418-pinctrl.dtsi

207 lines
3.4 KiB
Text
Raw Normal View History

arm: add support for SoC s5p4418 (cpu) / nanopi2 board Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01: - SPL not supported yet --> no spl-dir in arch/arm/cpu/armv7/s5p4418/. Appropriate line in Makefile removed. - cpu.c: '#include <cpu_func.h>' added. - arch/arm/cpu/armv7/s5p4418/u-boot.lds removed, is not required anylonger. - "obj-$(CONFIG_ARCH_NEXELL) += s5p-common/" added to arch/arm/cpu/armv7/Makefile since s5p-common/pwm.c is used instead of drivers/pwm/pwm-nexell.c. - s5p4418.dtsi: '#include "../../../include/generated/autoconf.h"' removed, is not necessary, error at out-of-tree building. '#ifdef CONFIG_CPU_NXP4330'-blocks (2x) removed. Some minor changes regarding mmc. 'u-boot,dm-pre-reloc' added to dp0 because of added DM_VIDEO support. - board/s5p4418/ renamed to board/friendlyarm/ - All s5p4418-boards except nanopi2 removed because there is no possibility to test the other boards. - Kconfig: Changes to have a structure like mach-bcm283x (RaspberryPi), e.g. "config ..." entries moved from/to other Kconfig. - "CONFIG_" removed from several s5p4418/nanopi2 specific defines because the appropriate values do not need to be configurable. - nanopi2/board.c: All getenv(), getenv_ulong(), setenv() and saveenv() renamed to env_get(), env_get_ulong(), env_set() and env_save(), respectively. MACH_TYPE_S5P4418 is not defined anymore, therefore appropriate code removed (not necessary for DT-kernels). - nanopi2/onewire.c: All crc8() renamed to crc8_ow() because crc8() is already defined in lib/crc8.c (with different parameters). - dts: "nexell,s5pxx18-i2c" used instead of "i2c-gpio", i2c0 and i2c1 added. gmac-, ehci- and dwc2otg-entries removed because the appropriate functionality is not supported yet. New mmc-property "mmcboost" added. s5p4418-pinctrl.dtsi: gmac-entries removed, mmc- and i2c-entries added. - '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where possible (and similar). Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
2020-07-10 17:07:37 +00:00
// SPDX-License-Identifier: GPL-2.0+
/*
* Nexell's s5p6818 SoC pin-mux and pin-config device tree source
*
* (C) Copyright 2020 Stefan Bosch <stefan_b@posteo.net>
*
* Copyright (C) 2016 Nexell Co., Ltd.
* http://www.nexell.co.kr
*
* Nexell's s5p6818 SoC pin-mux and pin-config options are listed as
* device tree nodes in this file.
*/
pinctrl@C0010000 {
/*
* values for "pin-pull":
* pulldown resistor = 0
* pullup = 1
* no pullup/down = 2
*/
/* MMC */
mmc0_clk: mmc0-clk {
pins = "gpioa-29";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <2>;
};
mmc0_cmd: mmc0-cmd {
pins = "gpioa-31";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <1>;
};
mmc0_bus4: mmc0-bus-width4 {
pins = "gpiob-1, gpiob-3, gpiob-5, gpiob-7";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <1>;
};
mmc1_clk: mmc1-clk {
pins = "gpiod-22";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <2>;
};
mmc1_cmd: mmc1-cmd {
pins = "gpiod-23";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <1>;
};
mmc1_bus4: mmc1-bus-width4 {
pins = "gpiod-24, gpiod-25, gpiod-26, gpiod-27";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <1>;
};
mmc2_clk: mmc2-clk {
pins = "gpioc-18";
pin-function = <2>;
pin-pull = <2>;
pin-strength = <2>;
};
mmc2_cmd: mmc2-cmd {
pins = "gpioc-19";
pin-function = <2>;
pin-pull = <2>;
pin-strength = <1>;
};
mmc2_bus4: mmc2-bus-width4 {
pins = "gpioc-20, gpioc-21, gpioc-22, gpioc-23";
pin-function = <2>;
pin-pull = <2>;
pin-strength = <1>;
};
mmc2_bus8: mmc2-bus-width8 {
nexell,pins = "gpioe-21", "gpioe-22", "gpioe-23", "gpioe-24";
pin-function = <2>;
pin-pull = <2>;
pin-strength = <1>;
};
/* I2C */
i2c0_sda:i2c0-sda {
pins = "gpiod-3";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
i2c0_scl:i2c0-scl {
pins = "gpiod-2";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
i2c1_sda:i2c1-sda {
pins = "gpiod-5";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
i2c1_scl:i2c1-scl {
pins = "gpiod-4";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
i2c2_sda:i2c2-sda {
pins = "gpiod-7";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
i2c2_scl:i2c2-scl {
pins = "gpiod-6";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
/* UART */
uart0_rx:uart0-rx {
pins = "gpiod-14";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
uart0_tx:uart0-tx {
pins = "gpiod-18";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
uart1_rx:uart1-rx {
pins = "gpiod-15";
pin-function = <2>;
pin-pull = <2>;
pin-strength = <0>;
};
uart1_tx:uart1-tx {
pins = "gpiod-19";
pin-function = <2>;
pin-pull = <2>;
pin-strength = <0>;
};
uart2_rx:uart2-rx {
pins = "gpiod-16";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
uart2_tx:uart2-tx {
pins = "gpiod-20";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
uart3_rx:uart3-rx {
pins = "gpiod-17";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
uart3_tx:uart3-tx {
pins = "gpiod-21";
pin-function = <1>;
pin-pull = <2>;
pin-strength = <0>;
};
uart4_rx:uart4-rx {
pins = "gpiob-28";
pin-function = <3>;
pin-pull = <2>;
pin-strength = <0>;
};
uart4_tx:uart4-tx {
pins = "gpiob-29";
pin-function = <3>;
pin-pull = <2>;
pin-strength = <0>;
};
arm: add support for SoC s5p4418 (cpu) / nanopi2 board Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01: - SPL not supported yet --> no spl-dir in arch/arm/cpu/armv7/s5p4418/. Appropriate line in Makefile removed. - cpu.c: '#include <cpu_func.h>' added. - arch/arm/cpu/armv7/s5p4418/u-boot.lds removed, is not required anylonger. - "obj-$(CONFIG_ARCH_NEXELL) += s5p-common/" added to arch/arm/cpu/armv7/Makefile since s5p-common/pwm.c is used instead of drivers/pwm/pwm-nexell.c. - s5p4418.dtsi: '#include "../../../include/generated/autoconf.h"' removed, is not necessary, error at out-of-tree building. '#ifdef CONFIG_CPU_NXP4330'-blocks (2x) removed. Some minor changes regarding mmc. 'u-boot,dm-pre-reloc' added to dp0 because of added DM_VIDEO support. - board/s5p4418/ renamed to board/friendlyarm/ - All s5p4418-boards except nanopi2 removed because there is no possibility to test the other boards. - Kconfig: Changes to have a structure like mach-bcm283x (RaspberryPi), e.g. "config ..." entries moved from/to other Kconfig. - "CONFIG_" removed from several s5p4418/nanopi2 specific defines because the appropriate values do not need to be configurable. - nanopi2/board.c: All getenv(), getenv_ulong(), setenv() and saveenv() renamed to env_get(), env_get_ulong(), env_set() and env_save(), respectively. MACH_TYPE_S5P4418 is not defined anymore, therefore appropriate code removed (not necessary for DT-kernels). - nanopi2/onewire.c: All crc8() renamed to crc8_ow() because crc8() is already defined in lib/crc8.c (with different parameters). - dts: "nexell,s5pxx18-i2c" used instead of "i2c-gpio", i2c0 and i2c1 added. gmac-, ehci- and dwc2otg-entries removed because the appropriate functionality is not supported yet. New mmc-property "mmcboost" added. s5p4418-pinctrl.dtsi: gmac-entries removed, mmc- and i2c-entries added. - '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where possible (and similar). Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
2020-07-10 17:07:37 +00:00
};