u-boot/board/Marvell/sheevaplug/sheevaplug.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * (C) Copyright 2009
 * Marvell Semiconductor <www.marvell.com>
 * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
 */

#ifndef __SHEEVAPLUG_H
#define __SHEEVAPLUG_H

#define SHEEVAPLUG_OE_LOW		(~(0))
#define SHEEVAPLUG_OE_HIGH		(~(0))
#define SHEEVAPLUG_OE_VAL_LOW		(1 << 29)	/* USB_PWEN low */
#define SHEEVAPLUG_OE_VAL_HIGH		(1 << 17)	/* LED pin high */

/* PHY related */
#define MV88E1116_LED_FCTRL_REG		10
#define MV88E1116_CPRSP_CR3_REG		21
#define MV88E1116_MAC_CTRL_REG		21
#define MV88E1116_PGADR_REG		22
#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)

#endif /* __SHEEVAPLUG_H */
SPDX: Convert all of our single license tags to Linux Kernel style When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com> 2018-05-06 21:58:06 +00:00			`/* SPDX-License-Identifier: GPL-2.0+ */`
Marvell Sheevaplug Board support Reference: http://plugcomputer.org/ http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support This patch is tested for- 1. Boot from DRAM/NAND flash 2. File transfer using tftp 3. NAND flash read/write/erase 4. Linux kernel and RFS Boot from NAND 5. Enabled USB PHY init for kernel need 6. Boot from USB supported Note: to boot Kirkwood kernel with USB support, you should add "usb start" in the boot sequence Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> 2009-07-16 15:28:00 +00:00			`/*`
			`* (C) Copyright 2009`
			`* Marvell Semiconductor <www.marvell.com>`
			`* Written-by: Prafulla Wadaskar <prafulla@marvell.com>`
			`*/`

			`#ifndef __SHEEVAPLUG_H`
			`#define __SHEEVAPLUG_H`

			`#define SHEEVAPLUG_OE_LOW (~(0))`
			`#define SHEEVAPLUG_OE_HIGH (~(0))`
			`#define SHEEVAPLUG_OE_VAL_LOW (1 << 29) /* USB_PWEN low */`
			`#define SHEEVAPLUG_OE_VAL_HIGH (1 << 17) /* LED pin high */`

			`/* PHY related */`
			`#define MV88E1116_LED_FCTRL_REG 10`
			`#define MV88E1116_CPRSP_CR3_REG 21`
			`#define MV88E1116_MAC_CTRL_REG 21`
			`#define MV88E1116_PGADR_REG 22`
			`#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)`
			`#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)`

			`#endif /* __SHEEVAPLUG_H */`