mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 17:07:38 +00:00
161 lines
2.8 KiB
Text
161 lines
2.8 KiB
Text
|
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||
|
/*
|
||
|
* Device tree for the uDPU board.
|
||
|
* Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
|
||
|
* Copyright (C) 2016 Marvell
|
||
|
* Copyright (C) 2019 Methode Electronics
|
||
|
* Copyright (C) 2019 Telus
|
||
|
*
|
||
|
* Vladimir Vid <vladimir.vid@sartura.hr>
|
||
|
*/
|
||
|
|
||
|
/dts-v1/;
|
||
|
|
||
|
#include <dt-bindings/gpio/gpio.h>
|
||
|
#include "armada-372x.dtsi"
|
||
|
|
||
|
/ {
|
||
|
chosen {
|
||
|
stdout-path = "serial0:115200n8";
|
||
|
};
|
||
|
|
||
|
memory@0 {
|
||
|
device_type = "memory";
|
||
|
reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
|
||
|
};
|
||
|
|
||
|
leds {
|
||
|
compatible = "gpio-leds";
|
||
|
|
||
|
led-power1 {
|
||
|
label = "udpu:green:power";
|
||
|
gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
|
||
|
};
|
||
|
|
||
|
led-power2 {
|
||
|
label = "udpu:red:power";
|
||
|
gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
|
||
|
};
|
||
|
|
||
|
led-network1 {
|
||
|
label = "udpu:green:network";
|
||
|
gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
|
||
|
};
|
||
|
|
||
|
led-network2 {
|
||
|
label = "udpu:red:network";
|
||
|
gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
|
||
|
};
|
||
|
|
||
|
led-alarm1 {
|
||
|
label = "udpu:green:alarm";
|
||
|
gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
|
||
|
};
|
||
|
|
||
|
led-alarm2 {
|
||
|
label = "udpu:red:alarm";
|
||
|
gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
|
||
|
};
|
||
|
};
|
||
|
|
||
|
sfp_eth1: sfp-eth1 {
|
||
|
compatible = "sff,sfp";
|
||
|
i2c-bus = <&i2c1>;
|
||
|
los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
|
||
|
mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
|
||
|
tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
|
||
|
tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
|
||
|
maximum-power-milliwatt = <3000>;
|
||
|
};
|
||
|
};
|
||
|
|
||
|
&sdhci0 {
|
||
|
status = "okay";
|
||
|
bus-width = <8>;
|
||
|
mmc-ddr-1_8v;
|
||
|
mmc-hs400-1_8v;
|
||
|
marvell,pad-type = "fixed-1-8v";
|
||
|
non-removable;
|
||
|
no-sd;
|
||
|
no-sdio;
|
||
|
};
|
||
|
|
||
|
&spi0 {
|
||
|
status = "okay";
|
||
|
pinctrl-names = "default";
|
||
|
pinctrl-0 = <&spi_quad_pins>;
|
||
|
|
||
|
flash@0 {
|
||
|
compatible = "jedec,spi-nor";
|
||
|
reg = <0>;
|
||
|
spi-max-frequency = <54000000>;
|
||
|
|
||
|
partitions {
|
||
|
compatible = "fixed-partitions";
|
||
|
#address-cells = <1>;
|
||
|
#size-cells = <1>;
|
||
|
|
||
|
partition@0 {
|
||
|
label = "firmware";
|
||
|
reg = <0x0 0x180000>;
|
||
|
};
|
||
|
|
||
|
partition@180000 {
|
||
|
label = "u-boot-env";
|
||
|
reg = <0x180000 0x10000>;
|
||
|
};
|
||
|
};
|
||
|
};
|
||
|
};
|
||
|
|
||
|
&pinctrl_nb {
|
||
|
i2c2_recovery_pins: i2c2-recovery-pins {
|
||
|
groups = "i2c2";
|
||
|
function = "gpio";
|
||
|
};
|
||
|
};
|
||
|
|
||
|
&i2c1 {
|
||
|
status = "okay";
|
||
|
pinctrl-names = "default", "recovery";
|
||
|
pinctrl-0 = <&i2c2_pins>;
|
||
|
pinctrl-1 = <&i2c2_recovery_pins>;
|
||
|
/delete-property/mrvl,i2c-fast-mode;
|
||
|
scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||
|
sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||
|
|
||
|
temp-sensor@48 {
|
||
|
compatible = "ti,tmp75c";
|
||
|
reg = <0x48>;
|
||
|
};
|
||
|
|
||
|
temp-sensor@49 {
|
||
|
compatible = "ti,tmp75c";
|
||
|
reg = <0x49>;
|
||
|
};
|
||
|
};
|
||
|
|
||
|
ð0 {
|
||
|
status = "okay";
|
||
|
managed = "in-band-status";
|
||
|
phys = <&comphy1 0>;
|
||
|
};
|
||
|
|
||
|
ð1 {
|
||
|
phy-mode = "sgmii";
|
||
|
status = "okay";
|
||
|
managed = "in-band-status";
|
||
|
phys = <&comphy0 1>;
|
||
|
sfp = <&sfp_eth1>;
|
||
|
};
|
||
|
|
||
|
&usb3 {
|
||
|
status = "okay";
|
||
|
phys = <&usb2_utmi_otg_phy>;
|
||
|
phy-names = "usb2-utmi-otg-phy";
|
||
|
};
|
||
|
|
||
|
&uart0 {
|
||
|
status = "okay";
|
||
|
};
|