u-boot/configs/Colombus_defconfig

CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-colombus"
CONFIG_SPL=y
CONFIG_MACH_SUN6I=y
CONFIG_DRAM_CLK=240
CONFIG_DRAM_ZQ=251
CONFIG_USB1_VBUS_PIN=""
CONFIG_I2C0_ENABLE=y
CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:2048,y:1536,depth:24,pclk_khz:208000,le:5,ri:150,up:9,lo:24,hs:5,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH27"
CONFIG_VIDEO_LCD_BL_EN="PM1"
CONFIG_VIDEO_LCD_BL_PWM="PH13"
CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_SYS_I2C_SLAVE=0x7f
CONFIG_SYS_I2C_SPEED=400000
CONFIG_PHY_REALTEK=y
CONFIG_ETH_DESIGNWARE=y
CONFIG_RGMII=y
CONFIG_MII=y
CONFIG_SUN7I_GMAC=y
CONFIG_AXP_ALDO1_VOLT=3300
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_OHCI_HCD=y
kconfig: remove meaningless prefixes in defconfig files Since commit e02ee2548afe (kconfig: switch to single .config configuration), the prefixes in defconfig files such as "+S:", "+ST:", etc., are meaningless. This commit was generated by the following command: find configs -name '_defconfig' \| xargs sed -i 's/^+ST://' Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> 2015-03-12 04:24:39 +00:00			`CONFIG_ARM=y`
			`CONFIG_ARCH_SUNXI=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2021-06-28 14:17:29 +00:00			`CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-colombus"`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2018-04-08 00:27:54 +00:00			`CONFIG_SPL=y`
kconfig: remove meaningless prefixes in defconfig files Since commit e02ee2548afe (kconfig: switch to single .config configuration), the prefixes in defconfig files such as "+S:", "+ST:", etc., are meaningless. This commit was generated by the following command: find configs -name '_defconfig' \| xargs sed -i 's/^+ST://' Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> 2015-03-12 04:24:39 +00:00			`CONFIG_MACH_SUN6I=y`
			`CONFIG_DRAM_CLK=240`
			`CONFIG_DRAM_ZQ=251`
			`CONFIG_USB1_VBUS_PIN=""`
sunxi: Display: Add support for eDP panels connected via an anx9804 bridge Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge, such as found on the Colombus devkit. While at it also fix the wrong indentation of the SSD2828 Kconfig help text in board/sunxi/Kconfig. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-08-08 14:13:53 +00:00			`CONFIG_I2C0_ENABLE=y`
			`CONFIG_AXP_GPIO=y`
			`CONFIG_VIDEO_LCD_MODE="x:2048,y:1536,depth:24,pclk_khz:208000,le:5,ri:150,up:9,lo:24,hs:5,vs:1,sync:3,vmode:0"`
			`CONFIG_VIDEO_LCD_DCLK_PHASE=0`
			`CONFIG_VIDEO_LCD_POWER="PH27"`
			`CONFIG_VIDEO_LCD_BL_EN="PM1"`
			`CONFIG_VIDEO_LCD_BL_PWM="PH13"`
			`CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2020-07-28 12:46:52 +00:00			`# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set`
Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACY First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot have SYS_I2C_LEGACY and DM_I2C at the same time, introduce CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only in SPL. Finally, for some PowerPC cases we also need CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to one or more symbols. Signed-off-by: Tom Rini <trini@konsulko.com> 2021-08-19 03:12:24 +00:00			`CONFIG_SPL_SYS_I2C_LEGACY=y`
Convert CONFIG_SYS_I2C_MVTWSI to Kconfig This converts the following to Kconfig: CONFIG_SYS_I2C_MVTWSI Signed-off-by: Tom Rini <trini@konsulko.com> 2021-08-17 21:59:47 +00:00			`CONFIG_SYS_I2C_MVTWSI=y`
Convert CONFIG_SYS_I2C_SPEED et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_I2C_SPEED CONFIG_SYS_I2C_SLAVE Signed-off-by: Tom Rini <trini@konsulko.com> 2021-08-19 03:12:32 +00:00			`CONFIG_SYS_I2C_SLAVE=0x7f`
			`CONFIG_SYS_I2C_SPEED=400000`
Convert CONFIG_PHYLIB et al to Kconfig This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: Tom Rini <trini@konsulko.com> 2020-04-24 19:35:53 +00:00			`CONFIG_PHY_REALTEK=y`
Kconfig: Move CONFIG_DESIGNWARE_ETH to Kconfig Move this to Kconfig and clean up board config files that use it. Also rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists in drivers/net/Kconfig. Signed-off-by: Simon Glass <sjg@chromium.org> Version 1: Acked-by: Joe Hershberger <joe.hershberger@ni.com> 2015-04-05 22:07:34 +00:00			`CONFIG_ETH_DESIGNWARE=y`
sunxi: Convert CONFIG_RGMII to Kconfig Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to update defconfig files of SYS_EXTRA_OPTIONS accordingly and remove it when it is possible. Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> 2017-04-02 10:59:08 +00:00			`CONFIG_RGMII=y`
Convert CONFIG_MII et al to Kconfig This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> 2018-07-21 04:03:57 +00:00			`CONFIG_MII=y`
sunxi: Move SUNXI_GMAC to Kconfig Move the SUNXI_GMAC config option to Kconfig, remove it from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC. Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> 2017-04-02 10:59:03 +00:00			`CONFIG_SUN7I_GMAC=y`
sunxi: power: Make all voltages configurable through Kconfig On boards with axp221/223 pmic-s we already allow configuring most voltages. Make the Kconfig options for these also apply to boards with axp152 / axp209 pmic-s and extend them to configure all voltages. The Kconfig defaults are chosen so that this commit does not introduce any functional changes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-09-30 13:22:42 +00:00			`CONFIG_AXP_ALDO1_VOLT=3300`
sunxi: Update selects in arch/arm/Kconfig for DM conversions With certain features being convert to DM now we want sunxi to default to having DM enabled for ETH/SERIAL and USB in some cases. Cc: Hans de Goede <hdegoede@redhat.com> Cc: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Tom Rini <trini@konsulko.com> [hdegoede@redhat.com: Also select CONFIG_USB for all sunxi builds] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Simon Glass <sjg@chromium.org> 2015-06-30 20:51:15 +00:00			`CONFIG_USB_EHCI_HCD=y`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2019-02-07 19:53:03 +00:00			`CONFIG_USB_OHCI_HCD=y`