mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-06 13:14:27 +00:00
79 lines
2.4 KiB
Text
79 lines
2.4 KiB
Text
|
Binding for Nexell s5pxx18 pin cotroller
|
||
|
|
========================================
|
||
|
|
|
||
|
|
Nexell's ARM bases SoC's integrates a GPIO and Pin mux/config hardware
|
||
|
|
controller. It controls the input/output settings on the available pads/pins
|
||
|
|
and also provides ability to multiplex and configure the output of various
|
||
|
|
on-chip controllers onto these pads.
|
||
|
|
|
||
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
||
|
|
common pinctrl bindings used by client devices, including the meaning of the
|
||
|
|
phrase "pin configuration node".
|
||
|
|
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: "nexell,s5pxx18-pinctrl"
|
||
|
|
- reg: should be register base and length as documented in the datasheet
|
||
|
|
- interrupts: interrupt specifier for the controller over gpio and alive pins
|
||
|
|
|
||
|
|
Example:
|
||
|
|
pinctrl_0: pinctrl@c0010000 {
|
||
|
|
compatible = "nexell,s5pxx18-pinctrl";
|
||
|
|
reg = <0xc0010000 0xf000>;
|
||
|
|
u-boot,dm-pre-reloc;
|
||
|
|
};
|
||
|
|
|
||
|
|
Nexell's pin configuration nodes act as a container for an arbitrary number of
|
||
|
|
subnodes. Each of these subnodes represents some desired configuration for a
|
||
|
|
pin, a group, or a list of pins or groups. This configuration can include the
|
||
|
|
mux function to select on those pin(s)/group(s), and various pin configuration
|
||
|
|
parameters.
|
||
|
|
|
||
|
|
Child nodes must be set at least one of the following settings:
|
||
|
|
- pins = Select pins for using this function.
|
||
|
|
- pin-function = Select the function for use in a selected pin.
|
||
|
|
- pin-pull = Pull up/down configuration.
|
||
|
|
- pin-strength = Drive strength configuration.
|
||
|
|
|
||
|
|
Valid values for nexell,pins are:
|
||
|
|
"gpioX-N" : X in {A,B,C,D,E}, N in {0-31}
|
||
|
|
Valid values for nexell,pin-function are:
|
||
|
|
"N" : N in {0-3}.
|
||
|
|
This setting means that the value is different for each pin.
|
||
|
|
Please refer to datasheet.
|
||
|
|
Valid values for nexell,pin-pull are:
|
||
|
|
"N" : 0 - Down, 1 - Up, 2 - Off
|
||
|
|
Valid values for nexell,pin-strength are:
|
||
|
|
"N" : 0,1,2,3
|
||
|
|
|
||
|
|
|
||
|
|
Example:
|
||
|
|
- pin settings
|
||
|
|
mmc0_clk: mmc0-clk {
|
||
|
|
pins = "gpioa-29";
|
||
|
|
pin-function = <1>;
|
||
|
|
pin-pull = <2>;
|
||
|
|
pin-strength = <2>;
|
||
|
|
};
|
||
|
|
|
||
|
|
mmc0_cmd: mmc0-cmd {
|
||
|
|
pins = "gpioa-31";
|
||
|
|
pin-function = <1>;
|
||
|
|
pin-pull = <2>;
|
||
|
|
pin-strength = <1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
mmc0_bus4: mmc0-bus-width4 {
|
||
|
|
pins = "gpiob-1, gpiob-3, gpiob-5, gpiob-7";
|
||
|
|
pin-function = <1>;
|
||
|
|
pin-pull = <2>;
|
||
|
|
pin-strength = <1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
- used by client devices
|
||
|
|
mmc0:mmc@... {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&mmc0_clk>, <&mmc0_cmd>, <&mmc0_bus4>;
|
||
|
|
...
|
||
|
|
};
|