u-boot/arch/arm/dts/zynqmp-zcu104-revA.dts

266 lines
4.8 KiB
Text
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0+
/*
* dts file for Xilinx ZynqMP ZCU104
*
* (C) Copyright 2017 - 2018, Xilinx, Inc.
*
* Michal Simek <michal.simek@xilinx.com>
*/
/dts-v1/;
#include "zynqmp.dtsi"
#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/phy/phy.h>
/ {
model = "ZynqMP ZCU104 RevA";
compatible = "xlnx,zynqmp-zcu104-revA", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
aliases {
ethernet0 = &gem3;
gpio0 = &gpio;
i2c0 = &i2c1;
mmc0 = &sdhci1;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
spi0 = &qspi;
usb0 = &usb0;
};
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
};
&can1 {
status = "okay";
};
&dcc {
status = "okay";
};
&gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
phy0: phy@c {
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
};
};
&gpio {
status = "okay";
};
&gpu {
status = "okay";
};
&i2c1 {
status = "okay";
clock-frequency = <400000>;
/* Another connection to this bus via PL i2c via PCA9306 - u45 */
i2c-mux@74 { /* u34 */
compatible = "nxp,pca9548";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x74>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/*
* IIC_EEPROM 1kB memory which uses 256B blocks
* where every block has different address.
* 0 - 256B address 0x54
* 256B - 512B address 0x55
* 512B - 768B address 0x56
* 768B - 1024B address 0x57
*/
eeprom: eeprom@54 { /* u23 */
compatible = "atmel,24c08";
reg = <0x54>;
#address-cells = <1>;
#size-cells = <1>;
};
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
compatible = "idt,8t49n287";
reg = <0x6c>;
};
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
#clock-cells = <0>;
compatible = "infineon,irps5401";
reg = <0x43>;
};
irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
#clock-cells = <0>;
compatible = "infineon,irps5401";
reg = <0x4d>;
};
};
i2c@4 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
tca6416_u97: gpio@21 {
compatible = "ti,tca6416";
reg = <0x21>;
gpio-controller;
#gpio-cells = <2>;
/*
* IRQ not connected
* Lines:
* 0 - IRPS5401_ALERT_B
* 1 - HDMI_8T49N241_INT_ALM
* 2 - MAX6643_OT_B
* 3 - MAX6643_FANFAIL_B
* 5 - IIC_MUX_RESET_B
* 6 - GEM3_EXP_RESET_B
* 7 - FMC_LPC_PRSNT_M2C_B
* 4, 10 - 17 - not connected
*/
};
};
i2c@5 {
#address-cells = <1>;
#size-cells = <0>;
reg = <5>;
};
i2c@7 {
#address-cells = <1>;
#size-cells = <0>;
reg = <7>;
};
/* 3, 6 not connected */
};
};
&qspi {
status = "okay";
flash@0 {
compatible = "m25p80"; /* n25q512a 128MiB */
#address-cells = <1>;
#size-cells = <1>;
reg = <0x0>;
spi-tx-bus-width = <1>;
spi-rx-bus-width = <4>;
spi-max-frequency = <108000000>; /* Based on DC1 spec */
partition@qspi-fsbl-uboot { /* for testing purpose */
label = "qspi-fsbl-uboot";
reg = <0x0 0x100000>;
};
partition@qspi-linux { /* for testing purpose */
label = "qspi-linux";
reg = <0x100000 0x500000>;
};
partition@qspi-device-tree { /* for testing purpose */
label = "qspi-device-tree";
reg = <0x600000 0x20000>;
};
partition@qspi-rootfs { /* for testing purpose */
label = "qspi-rootfs";
reg = <0x620000 0x5E0000>;
};
};
};
&rtc {
status = "okay";
};
&sata {
status = "okay";
/* SATA OOB timing settings */
ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
phy-names = "sata-phy";
phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
};
/* SD1 with level shifter */
&sdhci1 {
status = "okay";
no-1-8-v;
xlnx,mio_bank = <1>;
disable-wp;
};
&serdes {
status = "okay";
};
&uart0 {
status = "okay";
};
&uart1 {
status = "okay";
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
phy-names = "usb3-phy";
phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
maximum-speed = "super-speed";
};
&watchdog0 {
status = "okay";
};
&xilinx_ams {
status = "okay";
};
&ams_ps {
status = "okay";
};
&ams_pl {
status = "okay";
};