u-boot/board/freescale/p1010rdb/Makefile

# SPDX-License-Identifier: GPL-2.0+
#
# Copyright 2010-2011 Freescale Semiconductor, Inc.

MINIMAL=

ifdef CONFIG_SPL_BUILD
ifndef CONFIG_TPL_BUILD
ifdef CONFIG_SPL_INIT_MINIMAL
MINIMAL=y
endif
endif
endif

ifdef MINIMAL
obj-y	+= spl_minimal.o
else
ifdef CONFIG_SPL_BUILD
obj-y	+= spl.o
endif
obj-y	+= p1010rdb.o
obj-y	+= ddr.o
endif

obj-y	+= law.o
obj-y	+= tlb.o
SPDX: Convert all of our single license tags to Linux Kernel style When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com> 2018-05-06 21:58:06 +00:00			`# SPDX-License-Identifier: GPL-2.0+`
powerpc/85xx: Add basic support for P1010RDB Boot methods supported: NOR Flash, SPI Flash and SDCARD This patch adds the following basic interfaces: DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash. P1010RDB Overview ----------------- 1Gbyte DDR3 (on board DDR) Local Bus (IFC): 32Mbyte 16bit NOR flash 32Mbyte SLC NAND Flash 64KB CPLD device(GPCM interface) SPI Flash: 128 Mbit SPI Flash memory SD/MMC: connector to interface with the SD memory card SATA: 1 internal SATA connect to 2.5. 160G SATA2 HDD 1 eSATA connector to rear panel USB 2.0: x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface. x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet eTSEC: eTSEC1: Connected to RGMII PHY VSC8641XKO eTSEC2: Connected to SGMII PHY VSC8221 eTSEC3: Connected to SGMII PHY VSC8221 eCAN: Two DB-9 female connectors for Field bus interface UART: supports two UARTs up to 115200 bps for console TDM: 2 FXS ports connected via an external SLIC to the TDM interface. SLIC: SPI SLIC I2C: Serial EEprom Real time clock 256 Kbit M24256 I2C EEPROM PCIe: PCIe and mPCIe connectors. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> 2011-02-09 19:17:53 +00:00			`#`
			`# Copyright 2010-2011 Freescale Semiconductor, Inc.`

board/p1010rdb:Add NAND boot support using new SPL format - defines constants - Add spl_minimal.c to initialise DDR - update TLB entries as per NAND boot - remove nand_spl support for P1010RDB Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> 2013-04-16 07:58:12 +00:00			`MINIMAL=`

			`ifdef CONFIG_SPL_BUILD`
Convert CONFIG_SPL_INIT_MINIMAL et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_INIT_MINIMAL CONFIG_SPL_FLUSH_IMAGE CONFIG_SPL_SKIP_RELOCATE Signed-off-by: Tom Rini <trini@konsulko.com> 2022-05-13 16:26:35 +00:00			`ifndef CONFIG_TPL_BUILD`
board/p1010rdb:Add NAND boot support using new SPL format - defines constants - Add spl_minimal.c to initialise DDR - update TLB entries as per NAND boot - remove nand_spl support for P1010RDB Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> 2013-04-16 07:58:12 +00:00			`ifdef CONFIG_SPL_INIT_MINIMAL`
			`MINIMAL=y`
			`endif`
			`endif`
Convert CONFIG_SPL_INIT_MINIMAL et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_INIT_MINIMAL CONFIG_SPL_FLUSH_IMAGE CONFIG_SPL_SKIP_RELOCATE Signed-off-by: Tom Rini <trini@konsulko.com> 2022-05-13 16:26:35 +00:00			`endif`
board/p1010rdb:Add NAND boot support using new SPL format - defines constants - Add spl_minimal.c to initialise DDR - update TLB entries as per NAND boot - remove nand_spl support for P1010RDB Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> 2013-04-16 07:58:12 +00:00
			`ifdef MINIMAL`
freescale: Tweak various Makefiles to remove redundancy, fix aesthetics No intended functional change, just remove redundancies in some Makefiles, and make whitespace aesthetics uniform. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Reviewed-by: York Sun <york.sun@nxp.com> 2016-04-13 21:49:28 +00:00			`obj-y += spl_minimal.o`
board/p1010rdb:Add NAND boot support using new SPL format - defines constants - Add spl_minimal.c to initialise DDR - update TLB entries as per NAND boot - remove nand_spl support for P1010RDB Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> 2013-04-16 07:58:12 +00:00			`else`
powerpc: p1010rdb: Enable p1010rdb to start from NAND/SD/SPI flash with SPL In the previous patches, we introduced the SPL/TPL fraamework. For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The SPL was loaded by the code from the internal on-chip ROM. The SPL initializes the DDR according to the SPD and loads the final uboot image into DDR, then jump to the DDR to begin execution. For NAND booting way, the nand SPL has size limitation on some board(e.g. P1010RDB), it can not be more than 8KB, we can call it "minimal SPL", So the dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD and loads the final uboot image into DDR,then jump to the DDR to begin execution. This patch enabled SPL/TPL for P1010RDB to support starting from NAND/SD/SPI flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL. Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to execute, so the section .resetvec is no longer needed. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com> 2014-01-24 07:50:09 +00:00			`ifdef CONFIG_SPL_BUILD`
freescale: Tweak various Makefiles to remove redundancy, fix aesthetics No intended functional change, just remove redundancies in some Makefiles, and make whitespace aesthetics uniform. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Reviewed-by: York Sun <york.sun@nxp.com> 2016-04-13 21:49:28 +00:00			`obj-y += spl.o`
powerpc: p1010rdb: Enable p1010rdb to start from NAND/SD/SPI flash with SPL In the previous patches, we introduced the SPL/TPL fraamework. For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The SPL was loaded by the code from the internal on-chip ROM. The SPL initializes the DDR according to the SPD and loads the final uboot image into DDR, then jump to the DDR to begin execution. For NAND booting way, the nand SPL has size limitation on some board(e.g. P1010RDB), it can not be more than 8KB, we can call it "minimal SPL", So the dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD and loads the final uboot image into DDR,then jump to the DDR to begin execution. This patch enabled SPL/TPL for P1010RDB to support starting from NAND/SD/SPI flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL. Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to execute, so the section .resetvec is no longer needed. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com> 2014-01-24 07:50:09 +00:00			`endif`
board: powerpc: convert makefiles to Kbuild style Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Stefan Roese <sr@denx.de> 2013-10-21 02:53:38 +00:00			`obj-y += p1010rdb.o`
			`obj-y += ddr.o`
freescale: Tweak various Makefiles to remove redundancy, fix aesthetics No intended functional change, just remove redundancies in some Makefiles, and make whitespace aesthetics uniform. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Reviewed-by: York Sun <york.sun@nxp.com> 2016-04-13 21:49:28 +00:00			`endif`

board: powerpc: convert makefiles to Kbuild style Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Stefan Roese <sr@denx.de> 2013-10-21 02:53:38 +00:00			`obj-y += law.o`
			`obj-y += tlb.o`