u-boot/include/configs/P1022DS.h

/*
 * Copyright 2010 Freescale Semiconductor, Inc.
 * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
 *          Timur Tabi <timur@freescale.com>
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the Free
 * Software Foundation; either version 2 of the License, or (at your option)
 * any later version.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include "../board/freescale/common/ics307_clk.h"

/* High Level Configuration Options */
#define CONFIG_BOOKE			/* BOOKE */
#define CONFIG_E500			/* BOOKE e500 family */
#define CONFIG_MPC85xx			/* MPC8540/60/55/41/48 */
#define CONFIG_P1022
#define CONFIG_P1022DS
#define CONFIG_MP			/* support multiple processors */

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE	0xeff80000
#endif

#define CONFIG_FSL_ELBC			/* Has Enhanced localbus controller */
#define CONFIG_PCI			/* Enable PCI/PCIE */
#define CONFIG_PCIE1			/* PCIE controler 1 (slot 1) */
#define CONFIG_PCIE2			/* PCIE controler 2 (slot 2) */
#define CONFIG_PCIE3			/* PCIE controler 3 (ULI bridge) */
#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
#define CONFIG_FSL_PCIE_RESET		/* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
#define CONFIG_SYS_HAS_SERDES		/* has SERDES */

#define CONFIG_PHYS_64BIT
#define CONFIG_ENABLE_36BIT_PHYS
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP		16	/* number of TLB1 entries */

#define CONFIG_FSL_LAW			/* Use common FSL init code */

#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk()
#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk()
#define CONFIG_ICS307_REFCLK_HZ	33333000  /* ICS307 clock chip ref freq */

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_L2_CACHE
#define CONFIG_BTB

#define CONFIG_SYS_MEMTEST_START	0x00000000
#define CONFIG_SYS_MEMTEST_END		0x7fffffff

/*
 * Base addresses -- Note these are effective addresses where the
 * actual resources get mapped (not physical addresses)
 */
#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS		0xfffe00000ull
#define CONFIG_SYS_IMMR			CONFIG_SYS_CCSRBAR

/* DDR Setup */
#define CONFIG_DDR_SPD
#define CONFIG_VERY_BIG_RAM
#define CONFIG_FSL_DDR3

#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
#endif

#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_NUM_DDR_CONTROLLERS	1
#define CONFIG_DIMM_SLOTS_PER_CTLR	1
#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)

/* I2C addresses of SPD EEPROMs */
#define CONFIG_SYS_SPD_BUS_NUM		1
#define SPD_EEPROM_ADDRESS1		0x51	/* CTLR 0 DIMM 0 */

/*
 * Memory map
 *
 * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
 * 0x8000_0000	0xdfff_ffff	PCI Express Mem		1.5G non-cacheable
 * 0xffc0_0000	0xffc2_ffff	PCI IO range		192K non-cacheable
 *
 * Localbus cacheable (TBD)
 * 0xXXXX_XXXX	0xXXXX_XXXX	SRAM			YZ M Cacheable
 *
 * Localbus non-cacheable
 * 0xe000_0000	0xe80f_ffff	Promjet/free		128M non-cacheable
 * 0xe800_0000	0xefff_ffff	FLASH			128M non-cacheable
 * 0xffdf_0000	0xffdf_7fff	PIXIS			32K non-cacheable TLB0
 * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
 * 0xffe0_0000	0xffef_ffff	CCSR			1M non-cacheable
 */

/*
 * Local Bus Definitions
 */
#define CONFIG_SYS_FLASH_BASE		0xe0000000 /* start of FLASH 128M */
#define CONFIG_SYS_FLASH_BASE_PHYS	0xfe0000000ull

#define CONFIG_FLASH_BR_PRELIM  \
	(BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V)
#define CONFIG_FLASH_OR_PRELIM	(OR_AM_128MB | 0xff7)

#define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
#define CONFIG_SYS_OR0_PRELIM	CONFIG_FLASH_OR_PRELIM  /* NOR Options */

#define CONFIG_SYS_BR1_PRELIM	\
	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
#define CONFIG_SYS_OR1_PRELIM	CONFIG_FLASH_OR_PRELIM

#define CONFIG_SYS_FLASH_BANKS_LIST	\
	{CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS	2
#define CONFIG_SYS_MAX_FLASH_SECT	1024

#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE	/* start of monitor */

#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_MISC_INIT_R
#define CONFIG_HWCONFIG

#define CONFIG_FSL_NGPIXIS
#define PIXIS_BASE		0xffdf0000	/* PIXIS registers */
#define PIXIS_BASE_PHYS		0xfffdf0000ull

#define CONFIG_SYS_BR2_PRELIM	(BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
#define CONFIG_SYS_OR2_PRELIM	(OR_AM_32KB | 0x6ff7)

#define PIXIS_LBMAP_SWITCH	7
#define PIXIS_LBMAP_MASK	0xE0
#define PIXIS_LBMAP_ALTBANK	0x20

#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_END		0x00004000 /* End of used area in RAM */

#define CONFIG_SYS_GBL_DATA_SIZE	128	/* num bytes initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET	\
	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
#define CONFIG_SYS_MALLOC_LEN		(6 * 1024 * 1024)

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX		1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE	\
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)

/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "

/* Video */
#undef CONFIG_FSL_DIU_FB

#ifdef CONFIG_FSL_DIU_FB
#define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_CCSRBAR + 0x10000)
#define CONFIG_VIDEO
#define CONFIG_CMD_BMP
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
/*
 * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
 * disable empty flash sector detection, which is I/O-intensive.
 */
#undef CONFIG_SYS_FLASH_EMPTY_INFO
#endif

/*
 * Pass open firmware flat tree
 */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS

/* new uImage format support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE

/* I2C */
#define CONFIG_FSL_I2C
#define CONFIG_HARD_I2C
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED		400000
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
#define CONFIG_SYS_I2C_SLAVE		0x7F
#define CONFIG_SYS_I2C_NOPROBES		{{0, 0x29}}
#define CONFIG_SYS_I2C_OFFSET		0x3000
#define CONFIG_SYS_I2C2_OFFSET		0x3100

/*
 * I2C2 EEPROM
 */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
#define CONFIG_SYS_EEPROM_BUS_NUM	1

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */

/* controller 1, Slot 2, tgtid 1, Base address a000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc40000000ull
#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS	0xfffc20000ull
#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */

/* controller 2, direct to uli, tgtid 2, Base address 9000 */
#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS	0xfffc10000ull
#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */

/* controller 3, Slot 1, tgtid 3, Base address b000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc00000000ull
#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
#define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE3_IO_PHYS	0xfffc00000ull
#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */

#ifdef CONFIG_PCI
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP			/* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
#endif

/* SATA */
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA

#define CONFIG_SYS_SATA_MAX_DEVICE	2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA

#ifdef CONFIG_FSL_SATA
#define CONFIG_LBA48
#define CONFIG_CMD_SATA
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
#endif

#define CONFIG_MMC
#ifdef CONFIG_MMC
#define CONFIG_CMD_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_GENERIC_MMC
#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
#endif

#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif

#define CONFIG_TSEC_ENET
#ifdef CONFIG_TSEC_ENET

#define CONFIG_TSECV2
#define CONFIG_NET_MULTI

#define CONFIG_MII			/* MII PHY management */
#define CONFIG_TSEC1		1
#define CONFIG_TSEC1_NAME	"eTSEC1"
#define CONFIG_TSEC2		1
#define CONFIG_TSEC2_NAME	"eTSEC2"

#define TSEC1_PHY_ADDR		1
#define TSEC2_PHY_ADDR		2

#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)

#define TSEC1_PHYIDX		0
#define TSEC2_PHYIDX		0

#define CONFIG_ETHPRIME		"eTSEC1"

#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
#endif

/*
 * Environment
 */
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE		0x2000
#define CONFIG_ENV_SECT_SIZE	0x20000

#define CONFIG_LOADS_ECHO
#define CONFIG_SYS_LOADS_BAUD_CHANGE

/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_ELF
#define CONFIG_CMD_ERRATA
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_SETEXPR

#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
#define CONFIG_CMD_NET
#endif

/*
 * USB
 */
#define CONFIG_USB_EHCI

#ifdef CONFIG_USB_EHCI
#define CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_STORAGE
#define CONFIG_CMD_FAT
#endif

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS	16
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
#define CONFIG_SYS_HZ		1000

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 16 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/

#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
#endif

/*
 * Environment Configuration
 */

#define CONFIG_HOSTNAME		p1022ds
#define CONFIG_ROOTPATH		/opt/nfsroot
#define CONFIG_BOOTFILE		uImage
#define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */

#define CONFIG_LOADADDR		1000000

#define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */
#define CONFIG_BOOTARGS

#define CONFIG_BAUDRATE	115200

#define	CONFIG_EXTRA_ENV_SETTINGS					\
	"perf_mode=stable\0"						\
	"memctl_intlv_ctl=2\0"						\
	"netdev=eth0\0"							\
	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
	"tftpflash=tftpboot $loadaddr $uboot; "				\
		"protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
		"erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "		\
		"cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; "	\
		"protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "		\
		"cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0"	\
	"consoledev=ttyS0\0"						\
	"ramdiskaddr=2000000\0"						\
	"ramdiskfile=uramdisk\0"  		      	        	\
	"fdtaddr=c00000\0"	  			      		\
	"fdtfile=p1022ds.dtb\0"	  					\
	"bdev=sda3\0"		  			      		\
	"diuregs=md e002c000 1d\0"			 		\
	"dium=mw e002c01c\0" 						\
	"diuerr=md e002c014 1\0" 					\
	"othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 tty0\0" \
	"monitor=0-DVI\0"

#define CONFIG_HDBOOT					\
	"setenv bootargs root=/dev/$bdev rw "		\
	"console=$consoledev,$baudrate $othbootargs;"	\
	"tftp $loadaddr $bootfile;"			\
	"tftp $fdtaddr $fdtfile;"			\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_NFSBOOTCOMMAND						\
	"setenv bootargs root=/dev/nfs rw "				\
	"nfsroot=$serverip:$rootpath "					\
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;"			\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND						\
	"setenv bootargs root=/dev/ram rw "				\
	"console=$consoledev,$baudrate $othbootargs;"			\
	"tftp $ramdiskaddr $ramdiskfile;"				\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND		CONFIG_RAMBOOTCOMMAND

#endif