u-boot/drivers/usb/gadget/Kconfig

118 lines
3.7 KiB
Text
Raw Normal View History

#
# USB Gadget support on a system involves
# (a) a peripheral controller, and
# (b) the gadget driver using it.
#
# NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !!
#
# - Host systems (like PCs) need CONFIG_USB (with "A" jacks).
# - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks).
# - Some systems have both kinds of controllers.
#
# With help from a special transceiver and a "Mini-AB" jack, systems with
# both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG).
#
menuconfig USB_GADGET
bool "USB Gadget Support"
help
USB is a master/slave protocol, organized with one master
host (such as a PC) controlling up to 127 peripheral devices.
The USB hardware is asymmetric, which makes it easier to set up:
you can't connect a "to-the-host" connector to a peripheral.
U-Boot can run in the host, or in the peripheral. In both cases
you need a low level bus controller driver, and some software
talking to it. Peripheral controllers are often discrete silicon,
or are integrated with the CPU in a microcontroller. The more
familiar host side controllers have names like "EHCI", "OHCI",
or "UHCI", and are usually integrated into southbridges on PC
motherboards.
Enable this configuration option if you want to run U-Boot inside
a USB peripheral device. Configure one hardware driver for your
peripheral/device side bus controller, and a "gadget driver" for
your peripheral protocol.
if USB_GADGET
config USB_GADGET_ATMEL_USBA
bool "Atmel USBA"
select USB_GADGET_DUALSPEED
help
USBA is the integrated high-speed USB Device controller on
the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel.
config USB_GADGET_BCM_UDC_OTG_PHY
bool "Broadcom UDC OTG PHY"
help
Enable the Broadcom UDC OTG physical device interface.
config USB_GADGET_DWC2_OTG
bool "DesignWare USB2.0 HS OTG controller (gadget mode)"
select USB_GADGET_DUALSPEED
help
The Designware USB2.0 high-speed gadget controller
integrated into many SoCs. Select this option if you want the
driver to operate in Peripheral mode. This option requires
USB_GADGET to be enabled.
if USB_GADGET_DWC2_OTG
config USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8
bool "DesignWare USB2.0 HS OTG controller 8-bit PHY bus width"
help
Set the Designware USB2.0 high-speed OTG controller
PHY interface width to 8 bits, rather than the default (16 bits).
endif # USB_GADGET_DWC2_OTG
config CI_UDC
bool "ChipIdea device controller"
select USB_GADGET_DUALSPEED
help
Say Y here to enable device controller functionality of the
ChipIdea driver.
config USB_GADGET_VBUS_DRAW
int "Maximum VBUS Power usage (2-500 mA)"
range 2 500
default 2
help
Some devices need to draw power from USB when they are
configured, perhaps to operate circuitry or to recharge
batteries. This is in addition to any local power supply,
such as an AC adapter or batteries.
Enter the maximum power your device draws through USB, in
milliAmperes. The permitted range of values is 2 - 500 mA;
0 mA would be legal, but can make some hosts misbehave.
This value will be used except for system-specific gadget
drivers that have more specific information.
# Selected by UDC drivers that support high-speed operation.
config USB_GADGET_DUALSPEED
bool
config USB_GADGET_DOWNLOAD
bool "Enable USB download gadget"
help
Composite USB download gadget support (g_dnl) for download functions.
This code works on top of composite gadget.
if USB_GADGET_DOWNLOAD
config G_DNL_MANUFACTURER
string "Vendor name of USB device"
config G_DNL_VENDOR_NUM
hex "Vendor ID of USB device"
config G_DNL_PRODUCT_NUM
hex "Product ID of USB device"
endif # USB_GADGET_DOWNLOAD
endif # USB_GADGET