u-boot/drivers/ddr/marvell/a38x/ddr3_training_ip.h

164 lines
3.8 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (C) Marvell International Ltd. and its affiliates
*/
#ifndef _DDR3_TRAINING_IP_H_
#define _DDR3_TRAINING_IP_H_
#include "ddr_topology_def.h"
#define TIP_ENG_LOCK 0x02000000
#define TIP_TX_DLL_RANGE_MAX 64
#define GET_MIN(arg1, arg2) ((arg1) < (arg2)) ? (arg1) : (arg2)
#define GET_MAX(arg1, arg2) ((arg1) < (arg2)) ? (arg2) : (arg1)
#define INIT_CONTROLLER_MASK_BIT 0x00000001
#define STATIC_LEVELING_MASK_BIT 0x00000002
#define SET_LOW_FREQ_MASK_BIT 0x00000004
#define LOAD_PATTERN_MASK_BIT 0x00000008
#define SET_MEDIUM_FREQ_MASK_BIT 0x00000010
#define WRITE_LEVELING_MASK_BIT 0x00000020
#define LOAD_PATTERN_2_MASK_BIT 0x00000040
#define READ_LEVELING_MASK_BIT 0x00000080
#define SW_READ_LEVELING_MASK_BIT 0x00000100
#define WRITE_LEVELING_SUPP_MASK_BIT 0x00000200
#define PBS_RX_MASK_BIT 0x00000400
#define PBS_TX_MASK_BIT 0x00000800
#define SET_TARGET_FREQ_MASK_BIT 0x00001000
#define ADJUST_DQS_MASK_BIT 0x00002000
#define WRITE_LEVELING_TF_MASK_BIT 0x00004000
#define LOAD_PATTERN_HIGH_MASK_BIT 0x00008000
#define READ_LEVELING_TF_MASK_BIT 0x00010000
#define WRITE_LEVELING_SUPP_TF_MASK_BIT 0x00020000
#define DM_PBS_TX_MASK_BIT 0x00040000
#define RL_DQS_BURST_MASK_BIT 0x00080000
#define CENTRALIZATION_RX_MASK_BIT 0x00100000
#define CENTRALIZATION_TX_MASK_BIT 0x00200000
#define TX_EMPHASIS_MASK_BIT 0x00400000
#define PER_BIT_READ_LEVELING_TF_MASK_BIT 0x00800000
#define VREF_CALIBRATION_MASK_BIT 0x01000000
#define WRITE_LEVELING_LF_MASK_BIT 0x02000000
/* DDR4 Specific Training Mask bits */
ddr: marvell: a38x: Add support for DDR4 from Marvell mv-ddr-marvell repository This syncs drivers/ddr/marvell/a38x/ with the master branch of repository https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git up to the commit "mv_ddr: a3700: Use the right size for memset to not overflow" d5acc10c287e40cc2feeb28710b92e45c93c702c This patch was created by following steps: 1. Replace all a38x files in U-Boot tree by files from upstream github Marvell mv-ddr-marvell repository. 2. Run following command to omit portions not relevant for a38x, ddr3, and ddr4: files=drivers/ddr/marvell/a38x/* unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_APN806 \ -UCONFIG_MC_STATIC -UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \ -UCONFIG_PHY_STATIC_PRINT -UCONFIG_CUSTOMER_BOARD_SUPPORT \ -UCONFIG_A3700 -UA3900 -UA80X0 -UA70X0 -DCONFIG_ARMADA_38X -UCONFIG_ARMADA_39X \ -UCONFIG_64BIT $files 3. Manually change license to SPDX-License-Identifier (upstream license in upstream github repository contains long license texts and U-Boot is using just SPDX-License-Identifier. After applying this patch, a38x, ddr3, and ddr4 code in upstream Marvell github repository and in U-Boot would be fully identical. So in future applying above steps could be used to sync code again. The only change in this patch are: 1. Some fixes with include files. 2. Some function return and basic type defines changes in mv_ddr_plat.c (to correct Marvell bug). 3. Remove of dead code in newly copied files (as a result of the filter script stripping out everything other than a38x, dd3, and ddr4). Reference: "ddr: marvell: a38x: Sync code with Marvell mv-ddr-marvell repository" https://source.denx.de/u-boot/u-boot/-/commit/107c3391b95bcc2ba09a876da4fa0c31b6c1e460 Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2023-01-19 03:03:04 +00:00
#if defined (CONFIG_DDR4)
#define RECEIVER_CALIBRATION_MASK_BIT 0x04000000
#define WL_PHASE_CORRECTION_MASK_BIT 0x08000000
#define DQ_VREF_CALIBRATION_MASK_BIT 0x10000000
#define DQ_MAPPING_MASK_BIT 0x20000000
#define DM_TUNING_MASK_BIT 0x40000000
#endif /* CONFIG_DDR4 */
enum hws_result {
TEST_FAILED = 0,
TEST_SUCCESS = 1,
NO_TEST_DONE = 2
};
enum hws_training_result {
RESULT_PER_BIT,
RESULT_PER_BYTE
};
enum auto_tune_stage {
INIT_CONTROLLER,
STATIC_LEVELING,
SET_LOW_FREQ,
LOAD_PATTERN,
SET_MEDIUM_FREQ,
WRITE_LEVELING,
LOAD_PATTERN_2,
READ_LEVELING,
ddr: marvell: a38x: Add support for DDR4 from Marvell mv-ddr-marvell repository This syncs drivers/ddr/marvell/a38x/ with the master branch of repository https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git up to the commit "mv_ddr: a3700: Use the right size for memset to not overflow" d5acc10c287e40cc2feeb28710b92e45c93c702c This patch was created by following steps: 1. Replace all a38x files in U-Boot tree by files from upstream github Marvell mv-ddr-marvell repository. 2. Run following command to omit portions not relevant for a38x, ddr3, and ddr4: files=drivers/ddr/marvell/a38x/* unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_APN806 \ -UCONFIG_MC_STATIC -UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \ -UCONFIG_PHY_STATIC_PRINT -UCONFIG_CUSTOMER_BOARD_SUPPORT \ -UCONFIG_A3700 -UA3900 -UA80X0 -UA70X0 -DCONFIG_ARMADA_38X -UCONFIG_ARMADA_39X \ -UCONFIG_64BIT $files 3. Manually change license to SPDX-License-Identifier (upstream license in upstream github repository contains long license texts and U-Boot is using just SPDX-License-Identifier. After applying this patch, a38x, ddr3, and ddr4 code in upstream Marvell github repository and in U-Boot would be fully identical. So in future applying above steps could be used to sync code again. The only change in this patch are: 1. Some fixes with include files. 2. Some function return and basic type defines changes in mv_ddr_plat.c (to correct Marvell bug). 3. Remove of dead code in newly copied files (as a result of the filter script stripping out everything other than a38x, dd3, and ddr4). Reference: "ddr: marvell: a38x: Sync code with Marvell mv-ddr-marvell repository" https://source.denx.de/u-boot/u-boot/-/commit/107c3391b95bcc2ba09a876da4fa0c31b6c1e460 Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2023-01-19 03:03:04 +00:00
#if defined(CONFIG_DDR4)
SW_READ_LEVELING,
#endif /* CONFIG_DDR4 */
WRITE_LEVELING_SUPP,
PBS_RX,
PBS_TX,
SET_TARGET_FREQ,
ADJUST_DQS,
WRITE_LEVELING_TF,
READ_LEVELING_TF,
WRITE_LEVELING_SUPP_TF,
DM_PBS_TX,
VREF_CALIBRATION,
CENTRALIZATION_RX,
CENTRALIZATION_TX,
TX_EMPHASIS,
LOAD_PATTERN_HIGH,
PER_BIT_READ_LEVELING_TF,
ddr: marvell: a38x: Add support for DDR4 from Marvell mv-ddr-marvell repository This syncs drivers/ddr/marvell/a38x/ with the master branch of repository https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git up to the commit "mv_ddr: a3700: Use the right size for memset to not overflow" d5acc10c287e40cc2feeb28710b92e45c93c702c This patch was created by following steps: 1. Replace all a38x files in U-Boot tree by files from upstream github Marvell mv-ddr-marvell repository. 2. Run following command to omit portions not relevant for a38x, ddr3, and ddr4: files=drivers/ddr/marvell/a38x/* unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_APN806 \ -UCONFIG_MC_STATIC -UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \ -UCONFIG_PHY_STATIC_PRINT -UCONFIG_CUSTOMER_BOARD_SUPPORT \ -UCONFIG_A3700 -UA3900 -UA80X0 -UA70X0 -DCONFIG_ARMADA_38X -UCONFIG_ARMADA_39X \ -UCONFIG_64BIT $files 3. Manually change license to SPDX-License-Identifier (upstream license in upstream github repository contains long license texts and U-Boot is using just SPDX-License-Identifier. After applying this patch, a38x, ddr3, and ddr4 code in upstream Marvell github repository and in U-Boot would be fully identical. So in future applying above steps could be used to sync code again. The only change in this patch are: 1. Some fixes with include files. 2. Some function return and basic type defines changes in mv_ddr_plat.c (to correct Marvell bug). 3. Remove of dead code in newly copied files (as a result of the filter script stripping out everything other than a38x, dd3, and ddr4). Reference: "ddr: marvell: a38x: Sync code with Marvell mv-ddr-marvell repository" https://source.denx.de/u-boot/u-boot/-/commit/107c3391b95bcc2ba09a876da4fa0c31b6c1e460 Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2023-01-19 03:03:04 +00:00
#if defined(CONFIG_DDR4)
RECEIVER_CALIBRATION,
WL_PHASE_CORRECTION,
DQ_VREF_CALIBRATION,
DM_TUNING,
DQ_MAPPING,
#endif /* CONFIG_DDR4 */
WRITE_LEVELING_LF,
MAX_STAGE_LIMIT
};
enum hws_access_type {
ACCESS_TYPE_UNICAST = 0,
ACCESS_TYPE_MULTICAST = 1
};
enum hws_algo_type {
ALGO_TYPE_DYNAMIC,
ALGO_TYPE_STATIC
};
struct init_cntr_param {
int is_ctrl64_bit;
int do_mrs_phy;
int init_phy;
int msys_init;
};
struct pattern_info {
u8 num_of_phases_tx;
u8 tx_burst_size;
u8 delay_between_bursts;
u8 num_of_phases_rx;
u32 start_addr;
u8 pattern_len;
};
struct cs_element {
u8 cs_num;
u8 num_of_cs;
};
struct hws_tip_freq_config_info {
u8 is_supported;
u8 bw_per_freq;
u8 rate_per_freq;
};
struct hws_cs_config_info {
u32 cs_reg_value;
u32 cs_cbe_value;
};
struct dfx_access {
u8 pipe;
u8 client;
};
struct hws_xsb_info {
struct dfx_access *dfx_table;
};
int ddr3_tip_register_dq_table(u32 dev_num, u32 *table);
int hws_ddr3_tip_select_ddr_controller(u32 dev_num, int enable);
int hws_ddr3_tip_init_controller(u32 dev_num,
struct init_cntr_param *init_cntr_prm);
int hws_ddr3_tip_load_topology_map(u32 dev_num,
struct mv_ddr_topology_map *topology);
int hws_ddr3_tip_run_alg(u32 dev_num, enum hws_algo_type algo_type);
int ddr3_tip_is_pup_lock(u32 *pup_buf, enum hws_training_result read_mode);
u8 ddr3_tip_get_buf_min(u8 *buf_ptr);
u8 ddr3_tip_get_buf_max(u8 *buf_ptr);
#endif /* _DDR3_TRAINING_IP_H_ */