u-boot/arch/microblaze/cpu/start.S

329 lines
7.7 KiB
ArmAsm
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2007 Michal Simek
* (C) Copyright 2004 Atmark Techno, Inc.
*
* Michal SIMEK <monstr@monstr.eu>
* Yasushi SHOJI <yashi@atmark-techno.com>
*/
#include <asm-offsets.h>
#include <config.h>
.text
.global _start
_start:
mts rmsr, r0 /* disable cache */
addi r8, r0, __end
mts rslr, r8
#if defined(CONFIG_SPL_BUILD)
addi r1, r0, CONFIG_SPL_STACK_ADDR
#else
addi r1, r0, CONFIG_SYS_INIT_SP_OFFSET
#endif
addi r1, r1, -4 /* Decrement SP to top of memory */
/* Call board_init_f_alloc_reserve with the current stack pointer as
* parameter. */
add r5, r0, r1
bralid r15, board_init_f_alloc_reserve
nop
/* board_init_f_alloc_reserve returns a pointer to the allocated area
* in r3. Set the new stack pointer below this area. */
add r1, r0, r3
mts rshr, r1
addi r1, r1, -4
/* Call board_init_f_init_reserve with the address returned by
* board_init_f_alloc_reserve as parameter. */
add r5, r0, r3
bralid r15, board_init_f_init_reserve
nop
#if !defined(CONFIG_SPL_BUILD)
/* Setup vectors with pre-relocation symbols */
or r5, r0, r0
bralid r15, __setup_exceptions
nop
#endif
/* Flush cache before enable cache */
addik r5, r0, 0
addik r6, r0, XILINX_DCACHE_BYTE_SIZE
bralid r15, flush_cache
nop
/* enable instruction and data cache */
mfs r12, rmsr
ori r12, r12, 0x1a0
mts rmsr, r12
clear_bss:
/* clear BSS segments */
addi r5, r0, __bss_start
addi r4, r0, __bss_end
cmp r6, r5, r4
beqi r6, 3f
2:
swi r0, r5, 0 /* write zero to loc */
addi r5, r5, 4 /* increment to next loc */
cmp r6, r5, r4 /* check if we have reach the end */
bnei r6, 2b
3: /* jumping to board_init */
#ifdef CONFIG_DEBUG_UART
bralid r15, debug_uart_init
nop
#endif
#ifndef CONFIG_SPL_BUILD
or r5, r0, r0 /* flags - empty */
brai board_init_f
#else
brai board_init_r
#endif
1: bri 1b
#ifndef CONFIG_SPL_BUILD
.text
.ent __setup_exceptions
.align 2
/*
* Set up reset, interrupt, user exception and hardware exception vectors.
*
* Parameters:
* r5 - relocation offset (zero when setting up vectors before
* relocation, and gd->reloc_off when setting up vectors after
* relocation)
* - the relocation offset is added to the _exception_handler,
* _interrupt_handler and _hw_exception_handler symbols to reflect the
* post-relocation memory addresses
*
* Reserve registers:
* r10: Stores little/big endian offset for vectors
* r2: Stores imm opcode
* r3: Stores brai opcode
*/
__setup_exceptions:
addik r1, r1, -28
swi r2, r1, 4
swi r3, r1, 8
swi r6, r1, 12
swi r7, r1, 16
swi r8, r1, 20
swi r10, r1, 24
/* Find-out if u-boot is running on BIG/LITTLE endian platform
* There are some steps which is necessary to keep in mind:
* 1. Setup offset value to r6
* 2. Store word offset value to address 0x0
* 3. Load just byte from address 0x0
* 4a) LITTLE endian - r10 contains 0x2 because it is the smallest
* value that's why is on address 0x0
* 4b) BIG endian - r10 contains 0x0 because 0x2 offset is on addr 0x3
*/
addik r6, r0, 0x2 /* BIG/LITTLE endian offset */
lwi r7, r0, 0x28
swi r6, r0, 0x28 /* used first unused MB vector */
lbui r10, r0, 0x28 /* used first unused MB vector */
swi r7, r0, 0x28
/* add opcode instruction for 32bit jump - 2 instruction imm & brai */
addi r2, r0, 0xb0000000 /* hex b000 opcode imm */
addi r3, r0, 0xb8080000 /* hew b808 opcode brai */
#ifdef CONFIG_SYS_RESET_ADDRESS
/* reset address */
swi r2, r0, 0x0 /* reset address - imm opcode */
swi r3, r0, 0x4 /* reset address - brai opcode */
addik r6, r0, CONFIG_SYS_RESET_ADDRESS
sw r6, r1, r0
lhu r7, r1, r10
rsubi r8, r10, 0x2
sh r7, r0, r8
rsubi r8, r10, 0x6
sh r6, r0, r8
#endif
#ifdef CONFIG_SYS_USR_EXCEP
/* user_vector_exception */
swi r2, r0, 0x8 /* user vector exception - imm opcode */
swi r3, r0, 0xC /* user vector exception - brai opcode */
addik r6, r5, _exception_handler
sw r6, r1, r0
/*
* BIG ENDIAN memory map for user exception
* 0x8: 0xB000XXXX
* 0xC: 0xB808XXXX
*
* then it is necessary to count address for storing the most significant
* 16bits from _exception_handler address and copy it to
* 0xa address. Big endian use offset in r10=0 that's why is it just
* 0xa address. The same is done for the least significant 16 bits
* for 0xe address.
*
* LITTLE ENDIAN memory map for user exception
* 0x8: 0xXXXX00B0
* 0xC: 0xXXXX08B8
*
* Offset is for little endian setup to 0x2. rsubi instruction decrease
* address value to ensure that points to proper place which is
* 0x8 for the most significant 16 bits and
* 0xC for the least significant 16 bits
*/
lhu r7, r1, r10
rsubi r8, r10, 0xa
sh r7, r0, r8
rsubi r8, r10, 0xe
sh r6, r0, r8
#endif
/* interrupt_handler */
swi r2, r0, 0x10 /* interrupt - imm opcode */
swi r3, r0, 0x14 /* interrupt - brai opcode */
addik r6, r5, _interrupt_handler
sw r6, r1, r0
lhu r7, r1, r10
rsubi r8, r10, 0x12
sh r7, r0, r8
rsubi r8, r10, 0x16
sh r6, r0, r8
/* hardware exception */
swi r2, r0, 0x20 /* hardware exception - imm opcode */
swi r3, r0, 0x24 /* hardware exception - brai opcode */
addik r6, r5, _hw_exception_handler
sw r6, r1, r0
lhu r7, r1, r10
rsubi r8, r10, 0x22
sh r7, r0, r8
rsubi r8, r10, 0x26
sh r6, r0, r8
lwi r10, r1, 24
lwi r8, r1, 20
lwi r7, r1, 16
lwi r6, r1, 12
lwi r3, r1, 8
lwi r2, r1, 4
addik r1, r1, 28
2007-04-21 19:02:40 +00:00
rtsd r15, 8
or r0, r0, r0
.end __setup_exceptions
2007-04-21 19:02:40 +00:00
/*
* Read 16bit little endian
*/
.text
.global in16
.ent in16
.align 2
in16: lhu r3, r0, r5
bslli r4, r3, 8
bsrli r3, r3, 8
andi r4, r4, 0xffff
or r3, r3, r4
rtsd r15, 8
sext16 r3, r3
.end in16
/*
* Write 16bit little endian
* first parameter(r5) - address, second(r6) - short value
*/
.text
.global out16
.ent out16
.align 2
out16: bslli r3, r6, 8
bsrli r6, r6, 8
andi r3, r3, 0xffff
or r3, r3, r6
sh r3, r0, r5
rtsd r15, 8
or r0, r0, r0
.end out16
/*
* Relocate u-boot
*/
.text
.global relocate_code
.ent relocate_code
.align 2
relocate_code:
/*
* r5 - start_addr_sp
* r6 - new_gd
* r7 - reloc_addr
*/
addi r1, r5, 0 /* Start to use new SP */
addi r31, r6, 0 /* Start to use new GD */
add r23, r0, r7 /* Move reloc addr to r23 */
/* Relocate text and data - r12 temp value */
addi r21, r0, _start
addi r22, r0, __end - 4 /* Include BSS too */
rsub r6, r21, r22
or r5, r0, r0
1: lw r12, r21, r5 /* Load u-boot data */
sw r12, r23, r5 /* Write zero to loc */
cmp r12, r5, r6 /* Check if we have reach the end */
bneid r12, 1b
addi r5, r5, 4 /* Increment to next loc - relocate code */
/* R23 points to the base address. */
add r23, r0, r7 /* Move reloc addr to r23 */
addi r24, r0, CONFIG_SYS_TEXT_BASE /* Get reloc offset */
rsub r23, r24, r23 /* keep - this is already here gd->reloc_off */
/* Setup vectors with post-relocation symbols */
add r5, r0, r23 /* load gd->reloc_off to r5 */
bralid r15, __setup_exceptions
nop
/* Check if GOT exist */
addik r21, r23, _got_start
addik r22, r23, _got_end
cmpu r12, r21, r22
beqi r12, 2f /* No GOT table - jump over */
/* Skip last 3 entries plus 1 because of loop boundary below */
addik r22, r22, -0x10
/* Relocate the GOT. */
3: lw r12, r21, r0 /* Load entry */
addk r12, r12, r23 /* Add reloc offset */
sw r12, r21, r0 /* Save entry back */
cmpu r12, r21, r22 /* Check if this cross boundary */
bneid r12, 3b
addik r21. r21, 4
/* Update pointer to GOT */
mfs r20, rpc
addik r20, r20, _GLOBAL_OFFSET_TABLE_ + 8
addk r20, r20, r23
/* Flush caches to ensure consistency */
addik r5, r0, 0
addik r6, r0, XILINX_DCACHE_BYTE_SIZE
bralid r15, flush_cache
nop
2: addi r5, r31, 0 /* gd is initialized in board_r.c */
addi r6, r0, CONFIG_SYS_TEXT_BASE
addi r12, r23, board_init_r
bra r12 /* Jump to relocated code */
.end relocate_code
#endif