u-boot/drivers/hwmon/adm1021.c

/*
 * (C) Copyright 2003
 * Murray Jensen, CSIRO-MIT, Murray.Jensen@csiro.au
 *
 * based on dtt/lm75.c which is ...
 *
 * (C) Copyright 2001
 * Bill Hunter,  Wave 7 Optics, williamhunter@mediaone.net
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * Analog Devices's ADM1021
 * "Low Cost Microprocessor System Temperature Monitor"
 */

#include <common.h>

#include <i2c.h>
#include <dtt.h>

#define DTT_READ_LOC_VALUE	0x00
#define DTT_READ_REM_VALUE	0x01
#define DTT_READ_STATUS		0x02
#define DTT_READ_CONFIG		0x03
#define DTT_READ_CONVRATE	0x04
#define DTT_READ_LOC_HIGHLIM	0x05
#define DTT_READ_LOC_LOWLIM	0x06
#define DTT_READ_REM_HIGHLIM	0x07
#define DTT_READ_REM_LOWLIM	0x08
#define DTT_READ_DEVID		0xfe

#define DTT_WRITE_CONFIG	0x09
#define DTT_WRITE_CONVRATE	0x0a
#define DTT_WRITE_LOC_HIGHLIM	0x0b
#define DTT_WRITE_LOC_LOWLIM	0x0c
#define DTT_WRITE_REM_HIGHLIM	0x0d
#define DTT_WRITE_REM_LOWLIM	0x0e
#define DTT_WRITE_ONESHOT	0x0f

#define DTT_STATUS_BUSY		0x80	/* 1=ADC Converting */
#define DTT_STATUS_LHIGH	0x40	/* 1=Local High Temp Limit Tripped */
#define DTT_STATUS_LLOW		0x20	/* 1=Local Low Temp Limit Tripped */
#define DTT_STATUS_RHIGH	0x10	/* 1=Remote High Temp Limit Tripped */
#define DTT_STATUS_RLOW		0x08	/* 1=Remote Low Temp Limit Tripped */
#define DTT_STATUS_OPEN		0x04	/* 1=Remote Sensor Open-Circuit */

#define DTT_CONFIG_ALERT_MASKED	0x80	/* 0=ALERT Enabled, 1=ALERT Masked */
#define DTT_CONFIG_STANDBY	0x40	/* 0=Run, 1=Standby */

#define DTT_ADM1021_DEVID	0x41

typedef
	struct {
		uint i2c_addr:7;	/* 7bit i2c chip address */
		uint conv_rate:3;	/* conversion rate */
		uint enable_alert:1;	/* enable alert output pin */
		uint enable_local:1;	/* enable internal temp sensor */
		uint max_local:8;	/* internal temp maximum */
		uint min_local:8;	/* internal temp minimum */
		uint enable_remote:1;	/* enable remote temp sensor */
		uint max_remote:8;	/* remote temp maximum */
		uint min_remote:8;	/* remote temp minimum */
	}
dtt_cfg_t;

dtt_cfg_t dttcfg[] = CONFIG_SYS_DTT_ADM1021;

int
dtt_read (int sensor, int reg)
{
	dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
	uchar data;

	if (i2c_read(dcp->i2c_addr, reg, 1, &data, 1) != 0)
		return -1;

	return (int)data;
} /* dtt_read() */

int
dtt_write (int sensor, int reg, int val)
{
	dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
	uchar data;

	data = (uchar)(val & 0xff);

	if (i2c_write(dcp->i2c_addr, reg, 1, &data, 1) != 0)
		return 1;

	return 0;
} /* dtt_write() */

int
dtt_init_one(int sensor)
{
	dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
	int reg, val;

	if (((sensor & 1) == 0 ? dcp->enable_local : dcp->enable_remote) == 0)
		return 1;	/* sensor is disabled (or rather ignored) */

	/*
	 * Setup High Limit register
	 */
	if ((sensor & 1) == 0) {
		reg = DTT_WRITE_LOC_HIGHLIM;
		val = dcp->max_local;
	}
	else {
		reg = DTT_WRITE_REM_HIGHLIM;
		val = dcp->max_remote;
	}
	if (dtt_write (sensor, reg, val) != 0)
		return 1;

	/*
	 * Setup Low Limit register
	 */
	if ((sensor & 1) == 0) {
		reg = DTT_WRITE_LOC_LOWLIM;
		val = dcp->min_local;
	}
	else {
		reg = DTT_WRITE_REM_LOWLIM;
		val = dcp->min_remote;
	}
	if (dtt_write (sensor, reg, val) != 0)
		return 1;

	/* shouldn't hurt if the rest gets done twice */

	/*
	 * Setup Conversion Rate register
	 */
	if (dtt_write (sensor, DTT_WRITE_CONVRATE, dcp->conv_rate) != 0)
		return 1;

	/*
	 * Setup configuraton register
	 */
	val = 0;				/* running */
	if (dcp->enable_alert == 0)
		val |= DTT_CONFIG_ALERT_MASKED;	/* mask ALERT pin */
	if (dtt_write (sensor, DTT_WRITE_CONFIG, val) != 0)
		return 1;

	return 0;
} /* dtt_init_one() */

int
dtt_get_temp (int sensor)
{
	signed char val;

	if ((sensor & 1) == 0)
		val = dtt_read(sensor, DTT_READ_LOC_VALUE);
	else
		val = dtt_read(sensor, DTT_READ_REM_VALUE);

	return (int) val;
} /* dtt_get_temp() */