mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-10 23:24:38 +00:00
78 lines
1.7 KiB
C
78 lines
1.7 KiB
C
|
/*
|
||
|
|
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
|
||
|
|
*
|
||
|
|
* SPDX-License-Identifier: GPL-2.0+
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <common.h>
|
||
|
|
#include <miiphy.h>
|
||
|
|
#include <asm/io.h>
|
||
|
|
#include <asm/arch/cpu.h>
|
||
|
|
#include <asm/arch/soc.h>
|
||
|
|
#include <linux/mbus.h>
|
||
|
|
|
||
|
|
DECLARE_GLOBAL_DATA_PTR;
|
||
|
|
|
||
|
|
/* Base addresses for the external device chip selects */
|
||
|
|
#define DEV_CS0_BASE 0xe0000000
|
||
|
|
#define DEV_CS1_BASE 0xe1000000
|
||
|
|
#define DEV_CS2_BASE 0xe2000000
|
||
|
|
#define DEV_CS3_BASE 0xe3000000
|
||
|
|
|
||
|
|
/* Needed for dynamic (board-specific) mbus configuration */
|
||
|
|
extern struct mvebu_mbus_state mbus_state;
|
||
|
|
|
||
|
|
int board_early_init_f(void)
|
||
|
|
{
|
||
|
|
/*
|
||
|
|
* Don't configure MPP (pin multiplexing) and GPIO here,
|
||
|
|
* its already done in bin_hdr
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Setup some board specific mbus address windows
|
||
|
|
*/
|
||
|
|
mbus_dt_setup_win(&mbus_state, DEV_CS0_BASE, 16 << 20,
|
||
|
|
CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS0);
|
||
|
|
mbus_dt_setup_win(&mbus_state, DEV_CS1_BASE, 16 << 20,
|
||
|
|
CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS1);
|
||
|
|
mbus_dt_setup_win(&mbus_state, DEV_CS2_BASE, 16 << 20,
|
||
|
|
CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS2);
|
||
|
|
mbus_dt_setup_win(&mbus_state, DEV_CS3_BASE, 16 << 20,
|
||
|
|
CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS3);
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
int board_init(void)
|
||
|
|
{
|
||
|
|
/* adress of boot parameters */
|
||
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
int checkboard(void)
|
||
|
|
{
|
||
|
|
puts("Board: maxBCM\n");
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
#ifdef CONFIG_RESET_PHY_R
|
||
|
|
/* Configure and enable MV88E6185 switch */
|
||
|
|
void reset_phy(void)
|
||
|
|
{
|
||
|
|
u16 devadr = CONFIG_PHY_BASE_ADDR;
|
||
|
|
char *name = "neta0";
|
||
|
|
u16 reg;
|
||
|
|
|
||
|
|
if (miiphy_set_current_dev(name))
|
||
|
|
return;
|
||
|
|
|
||
|
|
/* todo: fill this with the real setup / config code */
|
||
|
|
|
||
|
|
printf("88E6185 Initialized on %s\n", name);
|
||
|
|
}
|
||
|
|
#endif /* CONFIG_RESET_PHY_R */
|