u-boot/board/cloudengines/pogo_e02/pogo_e02.c

119 lines
2.9 KiB
C
Raw Normal View History

/*
* Copyright (C) 2012
* David Purdy <david.c.purdy@gmail.com>
*
* Based on Kirkwood support:
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; If not, see <http://www.gnu.org/licenses/>.
*/
#include <common.h>
#include <miiphy.h>
#include <asm/arch/cpu.h>
#include <asm/arch/kirkwood.h>
#include <asm/arch/mpp.h>
#include "pogo_e02.h"
DECLARE_GLOBAL_DATA_PTR;
int board_early_init_f(void)
{
/*
* default gpio configuration
* There are maximum 64 gpios controlled through 2 sets of registers
* the below configuration configures mainly initial LED status
*/
kw_config_gpio(POGO_E02_OE_VAL_LOW,
POGO_E02_OE_VAL_HIGH,
POGO_E02_OE_LOW, POGO_E02_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
MPP3_NF_IO5,
MPP4_NF_IO6,
MPP5_NF_IO7,
MPP6_SYSRST_OUTn,
MPP7_GPO,
MPP8_UART0_RTS,
MPP9_UART0_CTS,
MPP10_UART0_TXD,
MPP11_UART0_RXD,
MPP12_SD_CLK,
MPP13_SD_CMD,
MPP14_SD_D0,
MPP15_SD_D1,
MPP16_SD_D2,
MPP17_SD_D3,
MPP18_NF_IO0,
MPP19_NF_IO1,
MPP29_TSMP9, /* USB Power Enable */
MPP48_GPIO, /* LED green */
MPP49_GPIO, /* LED orange */
0
};
kirkwood_mpp_conf(kwmpp_config);
return 0;
}
int board_init(void)
{
/* Boot parameters address */
gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
return 0;
}
#ifdef CONFIG_RESET_PHY_R
/* Configure and initialize PHY */
void reset_phy(void)
{
u16 reg;
u16 devadr;
char *name = "egiga0";
if (miiphy_set_current_dev(name))
return;
/* command to read PHY dev address */
if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
printf("Err..(%s) could not read PHY dev address\n", __func__);
return;
}
/*
* Enable RGMII delay on Tx and Rx for CPU port
* Ref: sec 4.7.2 of chip datasheet
*/
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
/* reset the phy */
miiphy_reset(name, devadr);
debug("88E1116 Initialized on %s\n", name);
}
#endif /* CONFIG_RESET_PHY_R */