ARM: add assembly routine to switch to non-secure state
While actually switching to non-secure state is one thing, another
part of this process is to make sure that we still have full access
to the interrupt controller (GIC).
The GIC is fully aware of secure vs. non-secure state, some
registers are banked, others may be configured to be accessible from
secure state only.
To be as generic as possible, we get the GIC memory mapped address
based on the PERIPHBASE value in the CBAR register. Since this
register is not architecturally defined, we check the MIDR before to
be from an A15 or A7.
For CPUs not having the CBAR or boards with wrong information herein
we allow providing the base address as a configuration variable.
Now that we know the GIC address, we:
a) allow private interrupts to be delivered to the core
(GICD_IGROUPR0 = 0xFFFFFFFF)
b) enable the CPU interface (GICC_CTLR[0] = 1)
c) set the priority filter to allow non-secure interrupts
(GICC_PMR = 0xFF)
Also we allow access to all coprocessor interfaces from non-secure
state by writing the appropriate bits in the NSACR register.
The generic timer base frequency register is only accessible from
secure state, so we have to program it now. Actually this should be
done from primary firmware before, but some boards seems to omit
this, so if needed we do this here with a board specific value.
The Versatile Express board does not need this, so we remove the
frequency from the configuration file here.
After having switched to non-secure state, we also enable the
non-secure GIC CPU interface, since this register is banked.
Since we need to call this routine also directly from the smp_pen
later (where we don't have any stack), we can only use caller saved
registers r0-r3 and r12 to not mess with the compiler.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-09-19 16:06:41 +00:00
|
|
|
#ifndef __GIC_V2_H__
|
|
|
|
|
#define __GIC_V2_H__
|
|
|
|
|
|
|
|
|
|
/* register offsets for the ARM generic interrupt controller (GIC) */
|
|
|
|
|
|
|
|
|
|
#define GIC_DIST_OFFSET 0x1000
|
|
|
|
|
#define GICD_CTLR 0x0000
|
|
|
|
|
#define GICD_TYPER 0x0004
|
|
|
|
|
#define GICD_IGROUPRn 0x0080
|
|
|
|
|
#define GICD_SGIR 0x0F00
|
|
|
|
|
|
|
|
|
|
#define GIC_CPU_OFFSET_A9 0x0100
|
|
|
|
|
#define GIC_CPU_OFFSET_A15 0x2000
|
|
|
|
|
#define GICC_CTLR 0x0000
|
|
|
|
|
#define GICC_PMR 0x0004
|
2013-09-19 16:06:44 +00:00
|
|
|
#define GICC_IAR 0x000C
|
|
|
|
|
#define GICC_EOIR 0x0010
|
ARM: add assembly routine to switch to non-secure state
While actually switching to non-secure state is one thing, another
part of this process is to make sure that we still have full access
to the interrupt controller (GIC).
The GIC is fully aware of secure vs. non-secure state, some
registers are banked, others may be configured to be accessible from
secure state only.
To be as generic as possible, we get the GIC memory mapped address
based on the PERIPHBASE value in the CBAR register. Since this
register is not architecturally defined, we check the MIDR before to
be from an A15 or A7.
For CPUs not having the CBAR or boards with wrong information herein
we allow providing the base address as a configuration variable.
Now that we know the GIC address, we:
a) allow private interrupts to be delivered to the core
(GICD_IGROUPR0 = 0xFFFFFFFF)
b) enable the CPU interface (GICC_CTLR[0] = 1)
c) set the priority filter to allow non-secure interrupts
(GICC_PMR = 0xFF)
Also we allow access to all coprocessor interfaces from non-secure
state by writing the appropriate bits in the NSACR register.
The generic timer base frequency register is only accessible from
secure state, so we have to program it now. Actually this should be
done from primary firmware before, but some boards seems to omit
this, so if needed we do this here with a board specific value.
The Versatile Express board does not need this, so we remove the
frequency from the configuration file here.
After having switched to non-secure state, we also enable the
non-secure GIC CPU interface, since this register is banked.
Since we need to call this routine also directly from the smp_pen
later (where we don't have any stack), we can only use caller saved
registers r0-r3 and r12 to not mess with the compiler.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-09-19 16:06:41 +00:00
|
|
|
|
|
|
|
|
#endif
|