u-boot/include/configs/omap5_uevm.h

127 lines
3.2 KiB
C
Raw Normal View History

/*
* (C) Copyright 2013
* Texas Instruments Incorporated.
* Sricharan R <r.sricharan@ti.com>
*
* Configuration settings for the TI EVM5430 board.
* See ti_omap5_common.h for omap5 common settings.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_OMAP5_EVM_H
#define __CONFIG_OMAP5_EVM_H
#ifndef CONFIG_SPL_BUILD
/* Define the default GPT table for eMMC */
#define PARTS_DEFAULT \
"uuid_disk=${uuid_gpt_disk};" \
"name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}"
#endif
#define DFU_ALT_INFO_MMC \
"dfu_alt_info_mmc=" \
"boot part 0 1;" \
"rootfs part 0 2;" \
"MLO fat 0 1;" \
"MLO.raw raw 0x100 0x100;" \
"u-boot.img.raw raw 0x300 0x400;" \
"spl-os-args.raw raw 0x80 0x80;" \
"spl-os-image.raw raw 0x900 0x2000;" \
"spl-os-args fat 0 1;" \
"spl-os-image fat 0 1;" \
"u-boot.img fat 0 1;" \
"uEnv.txt fat 0 1\0"
#define DFU_ALT_INFO_EMMC \
"dfu_alt_info_emmc=" \
"rawemmc raw 0 3751936;" \
"boot part 1 1;" \
"rootfs part 1 2;" \
"MLO fat 1 1;" \
"MLO.raw raw 0x100 0x100;" \
"u-boot.img.raw raw 0x300 0x400;" \
"spl-os-args.raw raw 0x80 0x80;" \
"spl-os-image.raw raw 0x900 0x2000;" \
"spl-os-args fat 1 1;" \
"spl-os-image fat 1 1;" \
"u-boot.img fat 1 1;" \
"uEnv.txt fat 1 1\0"
#define DFU_ALT_INFO_RAM \
"dfu_alt_info_ram=" \
"kernel ram 0x80200000 0x4000000;" \
"fdt ram 0x80f80000 0x80000;" \
"ramdisk ram 0x81000000 0x4000000\0"
#define DFUARGS \
"dfu_bufsiz=0x10000\0" \
DFU_ALT_INFO_MMC \
DFU_ALT_INFO_EMMC \
DFU_ALT_INFO_RAM
#include <configs/ti_omap5_common.h>
#define CONFIG_CONS_INDEX 3
#define CONFIG_SYS_NS16550_COM3 UART3_BASE
#define CONFIG_BAUDRATE 115200
#define CONFIG_MISC_INIT_R
/* MMC ENV related defines */
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */
#define CONFIG_ENV_SIZE (128 << 10)
#define CONFIG_ENV_OFFSET 0xE0000
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
/* Enhance our eMMC support / experience. */
#define CONFIG_CMD_GPT
#define CONFIG_EFI_PARTITION
#define CONFIG_HSMMC2_8BIT
#define CONFIG_SUPPORT_EMMC_BOOT
/* Required support for the TCA642X GPIO we have on the uEVM */
#define CONFIG_TCA642X
#define CONFIG_CMD_TCA642X
#define CONFIG_SYS_I2C_TCA642X_BUS_NUM 4
#define CONFIG_SYS_I2C_TCA642X_ADDR 0x22
/* USB UHH support options */
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_USB_STORAGE
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 80
#define CONFIG_OMAP_EHCI_PHY3_RESET_GPIO 79
/* USB Device Firmware Update support */
#define CONFIG_USB_FUNCTION_DFU
#define CONFIG_DFU_RAM
#define CONFIG_DFU_MMC
/* Enabled commands */
/* USB Networking options */
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_SMSC95XX
#define CONSOLEDEV "ttyO2"
/* Max time to hold reset on this board, see doc/README.omap-reset-time */
ARM: OMAP5: Fix warm reset with USB cable connected Warm reset on OMAP5 freezes when USB cable is connected. Fix requires PRM_RSTTIME.RSTTIME1 to be programmed with the time for which reset should be held low for the voltages and the oscillator to reach stable state. There are 3 parameters to be considered for calculating the time, which are mostly board and PMIC dependent. -1- Time taken by the Oscillator to shut + restart -2- PMIC OTP times -3- Voltage rail ramp times, which inturn depends on the PMIC slew rate and value of the voltage ramp needed. In order to keep the code in u-boot simple, have a way for boards to specify a pre computed time directly using the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC' option. If boards fail to specify the time, use a default as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead. Using the default value translates into some ~22ms and should work in all cases. However in order to avoid this large delay hiding other bugs, its recommended that all boards look at their respective data sheets and specify a pre computed and optimal value using 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC' In order to help future board additions to compute this config option value, add a README at doc/README.omap-reset-time which explains how to compute the value. Also update the toplevel README with the additional option and pointers to doc/README.omap-reset-time. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> [rnayak@ti.com: Updated changelog and added the README] Signed-off-by: Rajendra Nayak <rnayak@ti.com>
2013-04-17 20:49:40 +00:00
#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296
#define CONFIG_SCSI
#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
#endif /* __CONFIG_OMAP5_EVM_H */